No video :(

How to Replace Front Driver Side CV Axle 2004-2006 Scion xB

Подписаться 491 тыс.

Просмотров 12 тыс.

50% 1

Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AACV00347
This video shows you how to install a new front driver side CV axle in your 2004-2006 Scion xB. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This process should be similar on the following vehicles:
2004 Scion xB
2005 Scion xB
2006 Scion xB
Tools you will need:
• Pocket Screwdriver
• Pry Bar 1aau.to/obz/1AXAA00020
• 19mm Wrench 1aau.to/obF/1AXAA00010
• 14mm Socket 1aau.to/ogu/1AXAA00015
• 19mm Socket 1aau.to/ocI/1AXAA00043
• 21mm Socket 1aau.to/ocI/1AXAA00043
• 30mm 12-Point Socket 1aau.to/od/1AAST00002
• Dead Blow Hammer 1aau.to/obm/1AXAA00091
• Pliers
• 1/2 Inch Air Impact Gun 1aau.to/o5/1AXAA00252
• Torque Wrench 1aau.to/odY/1AXAA00044
• Bungee Cord
• Cloth Rags 1aau.to/oay/1AXSS00035
• Copper Anti-Seize
• Gloves 1aau.to/oak/1AXSS00048
• Liquid Thread Locker
• Rust Penetrant
• Transmission Fluid
• Center Punch 1aau.to/oN/1AXAA00055
• Drain Pan 1aau.to/oas/1AXAA00320
• Hammer 1aau.to/obm/1AXAA00091
• Jack Stands 1aau.to/obK/1AXAA00065
• Pick 1aau.to/oa6/1AXAA00037
• Rubber Mallet 1aau.to/oE/1AXAA00413
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Scion xB 2004-2006 1st Generation: • Scion xB 2004-2006 1st...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

30 авг 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@TRQ Год назад

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@carlosrios8121 Год назад

Thanks buddy. By looking at your video I was able to fix my 2008 scion xB. it took me 1.5 hours. 👍🏻

@TRQ Год назад

+Carlos Rios Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@jamesculp3622 7 месяцев назад

Real Nice Video! No BS talk or video about stuff that has no value! You could give classes in how to video.

@TheWilferch 11 месяцев назад

One more question.....it seems a lot of us have trouble inserting the unit into the trans. One hint is to grease-up the clip-groove.....this will help keep the clip "centered" instead if it falling down and protruding more on one-side vs the other. Comments?....the other thing is that a lot of mechanics say orient the clip with open side "up"...whereas the Toyota/Scion manual for my xA says keep the open side of the clip "down"...at the 6 o'clock position. If this is true....would 12 and 6 o'clock give the same affect....meaning...stay away fro 3 and 9 o'clock as these positions cause more trouble ??????

@TheWilferch 11 месяцев назад

Excellent tutorial with close-up shots.....small point.....couldn't really see what you did to remove the inner joint from the trans....seems you hand got in the way in this ONE place where I wish I could have seen it better. Did you use the crow-bar as a pickle-fork....meaning.....did you hit it with a hammer to use the "wedge-effect" of the tapered tip to get the joint off?....or... do you use the crow-bar tip as a "pry-bar" and leveraged against something ????

@johnathonwhyte2826 Год назад

Someone who knows how to work on a rusty car! Tapping the impact gun, not just laying on it. You've snapped enough rusty bolts in your day!

@thorsal2758 Год назад

Are the slotted rotors on right to each side?

@davidfigueroajr9462 11 месяцев назад

You guys don’t have a video of how to replaced starter of the xb.?

@TRQ 11 месяцев назад

+David Figueroa Jr We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-TRQ

@shellythrivelife Год назад

I have a question I just bought a 2009 Scion XB. When I put it in reverse or forward from being parked or sitting still. I hear a single ting noise. Single metal noise. This is what I’ve determined what I think it is. What noise do you most likely hear to determine this may need replaced. I used all my savings $5,300 - pretty much to buy this vehicle that supposedly had nothing wrong with it.

@intelin123 Год назад

If it humms at 50 or more yrs its a bad cv axle

@carlosrios8121 Год назад

At a stop making a turn if you hear a clunky noise most likely it is a cv axle

@dynoesaur 11 месяцев назад

I watch this video 7 months ago i changed both sides everything was going smooth until today i hear a clunking sound i don't know if they're defective or what