How to Replace Oil Pressure Sensor 1994-2004 Chevy S-10

Подписаться 469 тыс.

Просмотров 78 тыс.

50% 1

Buy Now!
New Oil Pressure Sender from 1AAuto.com 1aau.to/ic/1AOSU00021
Oil pressure is the lifeblood of any engine. The last thing you want to do is run your vehicle while oil pressure is low. Even if the oil is at the appropriate level, low pressure situations can still occur! This video shows you how to install a new oil pressure sensor on your 1994-2004 Chevy S-10.
• Check here for more videos on the 1994-2004 Chevy S-10 • Chevy S-10 2nd Generat...
This process should be similar on the following vehicles:
1994 Chevrolet S10
1995 Chevrolet S10
1996 Chevrolet S10
1997 Chevrolet S10
1998 Chevrolet S10
1999 Chevrolet S10
2000 Chevrolet S10
2001 Chevrolet S10
2002 Chevrolet S10
2003 Chevrolet S10
2004 Chevrolet S10
Tools you will need:
• Pocket Screwdriver
• 16mm Socket 1aau.to/oa/1AXAA00015
• Oil Pressure Switch Socket
• Vacuum
• Needle nose pliers 1aau.to/oa/1AXAA00051
• Needle nose pliers 1aau.to/oa/1AXAA00052
• T20 Driver 1aau.to/oa/1AXAA00008
• Ratchet 1aau.to/oa/1AXAA00016
• Socket Driver
• Socket Extensions 1aau.to/oa/1AXAA00015
• Marker / Writing Utensil
• Painter's Tape
• Paper Towels 1aau.to/oa/1AXSS00035
• Pick 1aau.to/oa/1AXAA00037
Subscribe: / @trq
Check out our playlist:
Chevy S-10 2nd Generation 1994-2004: • Chevy S-10 2nd Generat...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

28 мар 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 35

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@dragonflyfab9703 Год назад

The socket for the oil sensor is 26mm 12pt deep and wide!

@dragonflyfab9703 Год назад

This is by far the best instructional I have seen

@clandestine5959 3 года назад

Thanks a lot. The shop in my area wanted over $300.00 to do the job without the part. You saved me a bunch of money.

@anthonyguilianoii8836 2 года назад

My mechanic in Tampa FL is $175 plus the part. I did see another video where they left the distributor in and worked around it, after removing the cap.

@user-qf8lv6so5s Месяц назад

the only thing that could have made this video better is if he would have told you what the specialty socket was, other than that its an awesome instructional video.

@benjohnson8972 Год назад

If possible, can you edit the title to state it's for the V-6? Would save us 4-cyl guys some search time.

@jameshuban6515 Год назад

You answered my basic question about this issue. While the V8's switch is mounted vertically. My 4.3's switch is mounted horizontally. Under the distributor. Making it necessary to remove the distributor. So much for the easy fix. Thanks

@austinarkins8459 3 года назад

Great content! Just replaced this on 4/4/2021. Thank you for this.

@AstroVanTribe Год назад

I have an Astro van and for the first time, after watching the crap you have to go through with this vehicle, I'm happy to have the Astro - I have to remove the doghouse to get to the engine all the time, the OPS is right there - wow

@crazy-horsecrazyhorse8543 2 года назад

2002 Chevrolet S-10 4.3 V6, I’m having the zero oil pressure when warmed up at idle. WhenI first start up engine oil pressure reads 40,. 1st. I will replace the oil pressure sensor, and I will report my result after complete it this. Note: Prior to this I was having ticking sound of a possible collapsed lifter, I did the Oil change and shorted the oil by 1 quart and added 1 quart of ATV fluid, yes automatic transmission fluid, the collapsed lifter ticking sound is gone, but hopefully I will correct the oils pressure problem after replacement of the oil pressure sensor, again I will report back my results after replacing oil pressure sensor. P.S. Thanks for your video, it is appreciated. Peace Crazyhorse.

@jandefamily1670 2 года назад

did it work?

@deathleprosy27 Год назад

I’m having the ticking sound as well, did it get rid if the sound????!!

@dizzyassklown4424 Год назад

Best instrctional videos out there...👍

@TRQ Год назад

+Dizzy Assklown Thanks for the feedback! 1aau.to/m/Shop-TRQ

@lalo2641 3 года назад

Thanks

@samahdy Месяц назад

Does the distributor shaft gear ratio on this 4.3 make less than one revolution per cam shaft revolution or is it one to one? I'm asking because wouldn't it be simpler to remove the cap and mark the contact arm wherever it is and not go through all the business of cranking the engine manually?

@victorram6568 3 года назад

where do u mark the first crayon ? on wat part of the engine do u mark it?

@kaydenmorst4962 11 месяцев назад

My dashboard says check gauges, my oil psi is at 0 psi even after i warm up and sometimes it goes back to normal, but just yesterday my 01 zr2 turned off while i was driving, it didnt even make a mile. i have 329K. Would it be the sensor making the pump not work properly, or is it both?

@christopherlongstreet7904 4 месяца назад

A regular wrench will work fine if you can get it down there and its not crazy tight

@johnnyboy859 Год назад

Can we use Teflon tape on the threads?

@nicknorton3258 16 часов назад

I hope y'all not listening to this dude about taking the distributor out. Making a 20 min job 3+ hr job. Get you a short ratchet with a oil pressure sensor socket on it. Put the socket on the sensor first then the rachet next. Then back the sensor out, then put the new one back the same way.

@dragonclaw865 3 месяца назад

2.2L? No videos anywhere on them. Any pointers?

@ponch19821 2 года назад

What about the s10 with the 2.2 4cylinder?

@TRQ 2 года назад

+WJPonchAZ This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ