How to Replace Pitman Arm 1988-02 GMC Sierra 1500

Подписаться 533 тыс.

Просмотров 179 тыс.

50% 1

Buy Now!
New Pitman Arm from 1AAuto.com 1aau.to/id/1ASP...
A bad pitman arm can cause poor steering response, wandering, pulling and uneven tire wear. It can also be dangerous. This video shows you how to install a new pitman arm on your 1988-2002 GMC K1500.
• Check here for more videos on the 1988 to 2002 GMC K1500 Sierra: • GMC K1500 Sierra 1988-...
This process should be similar on the following vehicles:
1988 GMC K1500
1989 GMC K1500
1990 GMC K1500
1991 GMC K1500
1992 GMC K1500
1993 GMC K1500
1994 GMC K1500
1995 GMC K1500
1996 GMC K1500
1997 GMC K1500
1998 GMC K1500
1999 GMC K1500
Tools you will need:
• 15mm Socket 1aau.to/oSW/1AX...
• 21mm Socket 1aau.to/ouC/1AX...
• 22mm Socket 1aau.to/odr/1AX...
• 34mm Socket 1aau.to/ov/1AAS...
• Crowfoot Wrench
• Pickle Fork
• Pitman Arm Puller
• Straight Cutters
• 1/2 Inch Air Impact Gun 1aau.to/oen/1AX...
• Ratchet 1aau.to/oW4/1AX...
• Socket Driver
• Socket Extensions 1aau.to/oSW/1AX...
• Torque Wrench 1aau.to/oBF/1AX...
• Bungee Cord
• Liquid Thread Locker
• Rust Penetrant
• Drain Pan 1aau.to/ogD/1AX...
• Floor Jack 1aau.to/opT/1AX...
• Hammer 1aau.to/ooF/1AX...
• Jack Stands 1aau.to/oou/1AX...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
GMC K1500 Sierra 1988-2002 4th Gen: • GMC K1500 Sierra 1988-...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 96

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@photomasterstudios9495 3 года назад

Really happy that these GMC Sierra 1500 repair tutorials are here, especially since I'm doing a full front suspension rebuild on my 1997 Chevy K1500, everything seems to be the same except the lower ball joints.

@JoseDiaz-nl3ww 2 года назад

Agreeed bless the you tube gurus

@lht5dy31 Год назад

I did the same thing on my 89’ had no idea what to do Really easy

@petepower4217 Год назад

Thank you TRQ! I need to add that the young gentleman doing the work and narration does an excellent job at teaching those of us who want/need to know. I certainly appreciate his attention to detail, his light manner of delivery, and his obvious body of knowledge. I'm refurbishing practically all the bushings, the ball joints, the CV axles, the wheel hub bearings, idler bracket/idler arm, and pitman arm and TRQ's videos (along w/ "Suburban Ranch" videos, I must say) are an excellent resource. I'm old enough to remember life before the internet, going to the library to do research! I can't stand what social media has done to our society but find the web as somewhat of a Godsend for those of us that seek to us it as a learning tool.

@BrokeRecorder 3 года назад

I don't even own a chevy let alone a truck but you have gained a new subscriber today, short and to the point, I love it!!! No BS music in the background, explains everything he does, this is perfect, please don't ever stop!

@brockdyncatron3775 3 года назад

I just did mine. You dont need to pull the gear box. Jack the front end up. Loosen the driver side sway bar bushing on the frame. Remove the nuts off the pitman arm. Pull the ball joing end up and then with a pry bar pull the sway bar out of the way and fish out the pitman arm.

@archlab007 3 месяца назад

Excellent Video. I really like your method of pulling the steering box a lot better than getting underneath and trying to work with an old rusty, stubborn pitman arm...which likely you have to cut off anyway. Also, in doing it your way, you get to inspect a lot more and likely with the mileages on these trucks you're going to end up pulling the steering box anyway.

@peralez2383 2 года назад

never seen or heard of anyone taking off the whole gearbox to do this job, just did one...took off exactly 2 nuts and the pitman arm comes off

@PC-yz1jp 2 года назад

Right? I've done them on big C 7500 trucks and everything else for 40 years without pulling a steering box. Am I missing something?

@mcfriedchicken1972 2 года назад

I was thinking the same. And then remembered Eric the car guy also didn't remove the gear box when rebuilding his suspension

@mikep780 2 года назад

crossmember is in the way on these trucks look at 7:05.

@shadowghost456 Год назад

Thank you for this comment looking at it i didn't i would have to remove everything

@honkhonkler7732 Год назад

Ever done a 4x4? Cross member is in the way on my Suburban.

@AnthonyAlfaro22 2 года назад

Excellent videos Absolutely loved watching the entire video. My wife doesn’t get it, but it’s like an art form. Please continue the great content!!!!!!!

@SovereignLivingMan Год назад

That was a really good tutorial, glad I watched this first.

@trentpagani962 4 года назад

Great video! And that grunt when the power steering line broke loose made me laugh haha. Too relatable

@cesargranados8295 2 года назад

I’ve had the whole steering assembly on my Chevy c1500 and trust me they are strong and safe.. had them for 1yr now..

@daddydoc1115 6 месяцев назад

Great video! I have sloppy steering on a 1994 C1500, going to be replacing the gearbox and Pittman arm as we think thats where the problem is

@TRQ 6 месяцев назад

+@daddydoc1115 Thanks for watching our video! 1aau.to/m/Shop-TRQ

@kevinmanning4880 2 года назад

Great video, thank you so much for your great step by step!

@ronfriedly2681 Год назад

Great video. Just did a 94 Suburban and had to drop the gear box.

@lorenzoayala3352 2 года назад

Yeah paying a mechanic great video saved me some stress

@tomharless7257 4 года назад

Thank you . I’m doing this on my 95 k1500 in the next few weeks . Great video .

@pantherplatform 4 года назад

Ain't no way in hell I'm going to even attempt to remove the power steering gearbox.

@TRQ 4 года назад

+Panther Platform Thanks for the feedback! 1aau.to/m/Shop-TRQ

@pantherplatform 3 года назад

I live in the rust belt of northern Wisconsin. Everything up here built before 2010 is rusted to F. A simple pitman arm replacement could turn into an all day affair and an inflated repair bill really fast if one of those rusted lines breaks off at the flare nut.

@mariovo5 2 года назад

I'm gonna remove the steering gear box from my Kenworth the good thing about this is "I don't have to lift the truck.❤️

@LookInDJProduction 3 года назад

Appractiate the Torque of tightening. ;) great videos

@MrJdez09 2 года назад

Having a hard time believing you clicked it that easy at 180ftlbs on the ground.

@zenbowhunter 2 года назад

Thanks for a helpful video. Question: What type of threadlocker are you using on the various bolts?

@armaletalia3254 2 года назад

Don't use red. That is overkill. Permatex Orange is suitable.

@davidrod1969 Год назад

Thanks for the video. In order to separate the pitman/idler arm from the center link, do you have to disconnect the tie-rod ends from the steering knuckle?

@alfredocontreras37 2 года назад

Really good information, could you send information about vaccum hoses connection gmc 1500 photo

@miguelplascencia6093 3 года назад

What pitman arm puller is that the ones at autozone are tiny

@user-uq6vh3ps7m 5 месяцев назад

im having a hard time torquing that bolt on howd you do it so easily

@franklilley6613 4 месяца назад

Great video 👍

@pcdubya Год назад

Nicely done, question, at 6:08, what are those greasy shrouded 2 lines there? the transmission cooler lines? I have the same on a 94' Yukon but look like a major ordeal to replace those

@GwinnettLawns 2 года назад

I love your videos but where are you guys at? The rust on all the cars you video is absolutely horrible. We just don't have that in Atlanta.

@MoloneLabe Год назад

After doing my pitman arm. Everything went back on the same way it came off. My steering wheel is turned to the left pretty bad. All I did was take off the old pitman arm. Unbolt the 3 bolts holding on the steering box and then throw the new outman arm in the same position as where the old on came off and now it’s all out of wack.

@franciscohernandez-li8qe 3 года назад

The numbers u said to tighten them are they the same for 91 chevy c1500

@rmmm6725 2 года назад

Yes

@josealvarez6091 3 года назад

Great video very well detailed thanks for it

@TRQ 3 года назад

+Jose Alvarez Thanks for the feedback! 1aau.to/m/Shop-TRQ

@darken3150 2 года назад

When you tightened that second power steering pump line you didn't say "click" that means its not within torque spec :)

@tmangra Год назад

Dam, I don’t know what was harder, that or delivering my child

@rickoddo9811 2 года назад

i need to change my gearbox, how do i know if it is dead center before installing it?

@johnfig9579 6 месяцев назад

"We're going to torque this down to manufacturer's specification. The torque specification is...YES" (PROCEEDS TO UGGADUGGA)

@ericmoore7790 3 года назад

The complete kit from TRQ is great except for the lower ball joints. They do not fit

@stevethomas5209 2 года назад

Why would you need to change only a pitman arm? It's usually the whole steering box that needs changing. Can faulty pitman arm alone cause steering issues? In my case my steering is very sloppy. Thank you.

@sierraridgereaper 2 года назад

No need to change gear box. If the pitman arm is sloppy the steering will be loose and wander. Same with worn tie rod ends, idler arm and ball joints.

@okatexoffroad1813 3 года назад

Bought the kit , got it all on except the pitman arm. I’m trying like hell to not remove the power steering pump. I’ll leave method if I can get it

@drewshafer9379 3 года назад

Any updates?

@andyj2403 3 года назад

Physically impossible to do that

@arnoldromppai5395 3 года назад

cant see why you would even want to remove the power steering pump.. not needed

@vger13 3 года назад

i would say dont attempt without the airhammer picklefork , i beat on mine for 2 days before i borrowed one, then it still took a hour to work it out and had to cut it off the steering box

@LarsonFamilyFarm-LLC Год назад

Please explain WHY did you remove the steering gearbox?....the Pitman arm's two nuts are easily accessible....i can take those two nuts off under the car and I have room to separate the two joints...and i'm done...ready for new Pitman arm install. What am i missing.

@DashcamFootage22 Год назад

is your's 2 wheel or 4 wheel drive? I was reading that the cross member is in the way on the 4x4's. I have a 4x4 and I'm hoping I can do it without removing the gearbox. I'm not sure if I can. I just bought the truck yesterday

@a5v5805 4 года назад

Thank you for your video.

@TRQ 4 года назад

+Vincent N Thanks for watching our video! 1aau.to/m/Shop-TRQ

@MonsterNinjaz 2 года назад

Woah wait a min, what the heck did he use on that pickle fork.. i always have to hammer the damn thing

@ericksmelendez3821 3 года назад

Thank you awesome video now i could do mine

@TRQ 3 года назад

+Ericks Melendez Thanks for checking us out!

@lht5dy31 Год назад

When you did yours Did your pitman arm go completely down when u replaced it? Mine is not going completely down.

@MrRoy-rb1je 3 года назад

Outstanding!

@ericksmelendez3821 3 года назад

Thank you awesome video

@TRQ 3 года назад

+Ericks Melendez Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@davesmilingcoyote 2 года назад

What size pitman arm puller? Rock Auto has a few different sizes..

@taylorhoffman4859 2 года назад

Harbor freight Maddox has a tool set that is 89$ everything you will ever need for front end work on GM

@VtecdippinBB6siR 2 года назад

So, do I need to seat the arm completely down onto the shaft when installed? Or is it proper to have about 1/2" of spacing on the shaft?

@VtecdippinBB6siR 2 года назад

One part of the video when you're installing the arm, it looks like you left about half an inch to a quarter inch of spacing, from completely seating the arm. In the next clip on your video, the shaft appears to be fully seated with no spacing in between. Which one is correct? I do have trouble fully seating my steering arm onto the boxes shaft. And this is the 2nd moog branded arm that I've had to replace in the last 5 years. And 3rd moog branded pitman arm ive had to replace too.. Just making sure I'm not overlooking anything that's causing premature wear.. if you could get back to me, I'd appreciate it. Btw thanks for your video.

@VtecdippinBB6siR 2 года назад

I guess I've never forced the Arm completely onto the shaft. got a small fear of possibly stripping the nut or shaft threads. I've never tried to hit it with my Milwaukee and make it fully seat. Today I'm working on my pick up in the same exact area, and I could use a little guidance in this spot.

@whitewolf4016 3 года назад

Good job 👍

@josemedero7278 2 года назад

What can I do if my torque wrench goes only up to 150 ft lb. And the pitman arm needs to tighten to 185 ft lb ?????

@rmmm6725 2 года назад

Put your big boy pants on with a straight bar and tighten it down buddy. lol what else can you do

@sstheo01 2 года назад

Urgadurga !! 💪💪💪

@JonathanHarkey 8 месяцев назад

I did exactly what you did and now my power steering won’t work

@jesserousseau2481 3 года назад

I am debating on doing mine I have a 98 and my pitman arm has a wobble at the spline on the stearing box. The pitman arm looks knewer to me. I'm told that it's common that the knew arm can be messed up and not seat right. Idk about thos but how long dose this job take and what causes this to happen if the arm is knewer

@TRQ 3 года назад

+Jesse Rousseau Thanks for watching our video! 1aau.to/m/Shop-TRQ

@SF-fm7ov Год назад

I suspect the spline on your gearbox is no longer in good condition. Likely have to replace the gearbox and the pitman arm. There are both 3 and 4 key splines available. Perhaps your pitman arm did not match the gear box spline. If they didn't, they would never go together properly.

@diyspeed 4 года назад

I bought a TRQ set for my truck, I'm trying to get the damn pitman are off with the pickle fork but it's not separating. Any tips or trick to get the old pitman arm off?

@alb2571 3 года назад

Heat it up and wack it of

@thesenewythandlessuck Год назад

Are we still talking about a Pitman arm?

@HeresMinx 5 месяцев назад

Vehricle?

@harrassmentpanda6736 9 дней назад

Why is he pulling the steering box if the title is idler arm replacement 😭😂

@crankedkeymafia5179 3 года назад

Veericle

@evsnova74 Год назад

Underrated comment

@mygaminghands9875 2 года назад

Rip headphone users lol

@alexanderrogers8471 3 года назад

Is this possible to do this without any power tools?

@drewshafer9379 3 года назад

I currently doing the work right now on a 2001 gmc. I found that you remove the 34mm while its still on the truck using the mm socket and a breaker arm. The only thing is that you do have to remove all the armor from just below the radiator and just behind the pitman/ idler arm.

@screwstonstoner2196 3 года назад

I'm doing this on a 1999 C1500 everything is off so far, no power tools as well. Only issue is I can't get the pitman arm to go on as far as the original Got a axle nut kit from AutoZone for the 34mm and a pitman arm puller with a breaket, both are loaner tools

@Pursnikity_20022 4 года назад

Looks like a pain in the ass

@miguelplascencia6093 3 года назад

Not really you can remove it in about 15 minutes and put it back in 45min

@MakinEndsMeet69 Год назад

Pretty good video trq usually doesn't do a good job with their videos oh, one thing I did not like was the fact that we didn't bother cleaning up the power steering lines around the nuts! One thing for sure cleanliness is Next to Godliness