How To: Samsung Door Boot Seal DC64-00802B 

Now the world just needs this man to make how to videos on everything. Best how to video ever.

Very well explained. Thank you. I was able to (as a woman😂) by myself with help from this video, take apart my washer to remove the seal. I put it back on and put my washer back together and my washer works wonderfully. Thank you!

It still might take me 6 hours but I will never fail with these instructions.

Older Model Owners here are some notes. I followed the directions in the video (excellent) for my 15 years old Samsung washing machine. I did have to add some extra steps, importantly I had to remove the bottom rust color stone piece (using 1/2 inch ratchet) to get the gasket in place over the lip at the bottom (7 min mark of video) as there is not enough of a gap to install without removing the stone. Also with the top panel I removed the 4 easy attachments and kept the ones on the long black cable connected, leaving the top panel on top of the machine. I also had to disconnect the detergent draw screw to allow the top panel to be removed since the lip was in the way. I also re-attached the door switch harness, to the front panel with the panel on the bottom tabs before screwing in the front panel. You can tell if you have the same model I worked by seeing the rust stone on the bottom, in the video they are on the side. It took me 3 hours, including prep, cleaning during the project, and putting everything back in place.🙂

All manufacturers should look to this as an example of how to make a repair instructional video. Fantastic... Ol Sarge...

Great informative video! How do you keep this rubber door seal clean? Ours constantly get black spots and dirty like mildewy stuff. It’s gross and I tried many things. About to order a new one which is how I found this video

Your video was by far the best one out there because of the clear and detailed commentary on every step you did. That's the key to these how to's that many videos miss. Now I am confident to attempt this job. Thank you and much appreciated.

I just completed mine, took me 3 hrs with a few interruptions. 2 things to note; when removing the front panel of my machine I discouvered that there were 2 screws on the very bottom edge, they went through the metal "tabs", there are 3 tabs along the bottom but only 2 had screws...tough to reach as they face down, had to tilt/block the machine back at a steep angle. You cant get the front panel off without removing them. The other item is that the "control panel", has plastic "tabs" I broke one off so be careful leaning that part back while you unhook the wire harnesses. this vid was great, I wouldnt have attempted this without it!!

You have explained each step easily to understand and practice. Thank you so much

Saved me a couple hundred dollars by purchasing the part and fixing myself!! Thank you for your super easy to follow instructions!

I also used this to take out an old moldy seal and install a new one successfully. So much gratitude for making and sharing this video!

Great video! Clear and concise instructions, with a thorough follow through from start to finish. Thank you so very much for making this. You are going to save us DIY'ers so much money.

Awesome walk through! I have now been able to replace the seal and I also followed another of your videos to replace the heating element on my dryer. Couldn't have done it with a minimum of frustration if not for your easy to follow instructions . Thanks!

This is a great video but watch it a couple times and make sure to keep it handy when working on your machine. I actually had 7 connections in my control panel. I ended up just laying it on the top of the machine. I also had to remove the weights from the drum to unscrew the nut on the ring around the gasket. It all worked but took me about 2.5 hours.

YOU ARE MY HERO ❤ TYSM for this wonderful video. I mean I feel like I just went through a training course and I feel like a professional now 😅 Def a new subscriber here 🥰🥰🥰

I was able to fix my washer in just over an hour. Thanks for the step by step, saved me hundreds.

he model wasjer I have is slightly different, there are two screws undeneath to remove ! The video really did help me work through all this, started at 9:30 and was done by noon. Thumbs Up. KJ

This is the perfect example of how a DIY or repair video should be done. Kudos!

Thank you for the video. Repaired my washer in about an hour and saved me about $200. Legends.

What a great video, step by step explanation and everything! I just finished the job on a Samsung washer Model WF331ANW/XAA. Even though on my model, I had four screws (not 2) on the bottom of front panel in the filter well, and forward spring clamp was located on the side, no on the bottom, as well as the inner clamp was on the 9:00 o'clock position, the institutions helped me a lot. The only challenge was loosening/tightening the inner clamp bolt (the mounting blocks of the tub were on my way, so I ended up using a 90 degree screw driver and a crescent wrench (since I could not fit a socket there). Thank you so much!

Thanks! Helped to replace door on BubbleWash 7.5. Didn't remove the door completely but left it hanging down resting with the open door on the ground. Also removed the two white plastic lugs mid way on the front as couldn't get the door back on. Had the most difficulty getting the seal over the plastic lip on the inner drum - another video said to use dish washing detergent to ease it in, which helped. Once you've got the hang of pushing the seal over the lip it slides in nicely to a tight fit. Strangely satisfying to close the door onto the brand new seal :)

Excellent ! Not a handyman, but very well explained after 3 hours , all fixed and no leaks! Love the tips along the way! Thank you

Great video -- exactly what I needed. Saved me at least $150 in labour and another $50 in mark up on the part.

This is fantastic thank you for the great video and detailed steps. I was able to replace my boot that was leaking.

Extremely well done DIY! This really helps walk through all the steps to get this job done. Thank you!

Awesome! I probably saved $200 watching your video. Easy to follow step by step guidance. Those clamps tried to make it hard. Took me about 35 mins to complete. Thanks!

So far so good. I ran into a problem taking the front frame off...mine was held together at the bottom of washing machine by 2 screws. Overall, very well done & detailed. I had watched a couple of other videos on this by different people & yours was by far the best! Thank you so much for your help 😅

my speediest appliance repair yet. thanks! the newer models have a different electronics panel. i has to revive the soap dish receiver

I agree, well explained. I also appreciated the added clarifications around some techniques to use.

Excellent video as usual. I always go to Applicance Parts Pros for help on repairing household appliances. Your videos are alwasy accurate, complete and concise!

Outstanding instructional clarity. Bravo!

This video is perfect for fixing an issue yourself. Much appreciated

Thanks for the video we just bought a new home and the gasket in the washer was disgusting. I took it off using these instructions and washed it. Was a bit harder for me since my model had some sort of insulation that made really hard to get to the inner clips screw! But I managed to get it done.

That's doc! Very wel done! Fixed my washer with no issues ... currently running a cleaning cycle!

What a great video. It does not get better than this. THANK YOU. You have a new customer

Great video! Saved me a lot of money and finished in under an hour. Thank you for posting.

this is great clip. THANK YOU guys for putting such a fantastic simple to follow step by step repair video!

Wow, loud and clear, sir! Should be teaching craftmanship at trades uni. Posts of kudos.

I watched other videos on the same issues, yours was by far the best. Thank you!

Thanks Matt. Thoroughly and meticulously explained.

Helped alot.. minor issues in the way because of different model but same concept and got her done! Thanks you

With the new style Samsung Front Loaders, there are two small screws in the bottom of the front cover; preventing you from just lifting up and pulling the front cover off the machine. The screws are installed in the very bottom on the underside of the front cover that makes it impossible to access. Why Samsung did this is beyond me.... I really do appreciate your video!

Holy crap that’s a lot of work. This is the best video demonstration though! Great work! I’m not replacing mine, I can live with the mold marks 😢

Thank you! This will be very helpful when I have my door seal replaced. I was actually thinking I would need a new washer. But thanks to research and your video, problem solved and costs

Thank you very much for posting this video it was thorough and precise I probably would’ve been completely lost if I hadn’t watched it thank you

Great video. My seal is too dirty to clean with it installed, going to take it off and scrub it or order a new one if they aren’t too expensive (haven’t checked yet).

If this old house did this video, they would just say “ take the door off, change the seal and you’re done😂😂

Tremendous Help THANK YOU Its running so far no leaks....

Awesome video. Changed out my stinky moldy seal for a new clean one. Was very easy.

I just replaced the door gasket on my daughter-in-laws Samsung washer. The video was close enough and informative, thank you. I ran into a snag pulling the front door cover off as there were screws in the bottom flanges. I had to tip the washer up 45 degrees in order to remove them. The screws were missing in the bottom left filter cover?

Thank you! This video was tremendously helpful. 😃

Saved me $500. Thanks very much

Thanks so much for a very well produced video. Just ordered the part from you.

Excellent video! I have a newer model washer that had 7 wire harness connectors and 2 extra screws on the bottom of the front panel but no big deal. Worked great.

Once you watch this video, you should be able to replace the door boot seal on your washer. I need to order mine so I can install it once I watch this video one more time. Thanks!

This guy should be a teacher! Very specific instructions.

Thanks for the video. Wouldn’t have been able to do this without it. Took me much longer than I thought. My biggest issue was getting the control panel off. It got stuck in the soap dispenser side. I would suggest that if you get stuck getting it off, try disconnecting the dispenser for the inside. Mine only had one screw and made getting the panel back in was a snap.

THANK YOU for providing this excellent instructional video. I likely could not have made this repair without it.

What a great video, thanks for taking the time to put this together and post it.

Mate, your video just helped me do this on my Samsung. Really great video, thank you so much!!!! Much respect 👍🏼

I tell you the truth about Duck tape. It works for everything! Lol. I could not afford the actual replacement yet and am amazed that $5 tape is holding. But yes your last video easily got me through.

12:19 this finally worked! Thank you

Awesome video although not sure if it's just because it's a new factory seal boot but after first run it smells like rubber burning not too bad but obvious was thinking it was just cuz it's new

Great video! Thank you for sharing, being simple and detailed.

Thank you so mate! Very helpful. My washer varies a little from your video nonetheless same concept. Got her done! Thanks again.

Great video and walkthrough. Replacing the clamp took a few tries, but ultimately worked. Saved a bunch of time and money.

Great video, changed my gasket and the drum hits the gasket...any suggestions?

The seal got caught in the clothes causing the outer clamp to come off, I hope I can reposition it, appreciate the video.

Excellent video with detailed instructions no issues

Excellent how to video, Great Job!

Thank you. This was very very helpful, clear and informative. Thank you

You saved my life lol man I was struggling

What else should I typically check while I'm in there, ie: springs or balancing parts. Is there anpother video for a deep clean of the drum or the rim around the drum

Absolutely the best video ever!

Recently replaced our door boot seal as water was visibly dripping from the outside bottom of the door. Installed step by step and now I’m getting a leak during fill up, underneath the drum, directly under the boot seal. Checked all hoses, drain pump hoses cleaned, no visible leaks from the top inlet valves. I’m going to retrace my steps before I call a technician, but would the boot allow water to drip out of the drum? Just trying to think if it’s the boot or possibly the outer tub seal. (Which I’m hoping it isn’t). Great tutorial!

thanks for the part and the video help, it's plugged back in and working....

Thank you so much! Great video! God bless you

Your video was extreamly helpful.. great content.

with the right tool i can do this for a living

Excellent video and well explained. Thank you.

Great video! Taught me to never buy one of these pieces of garbage ever again!

Does the seal need to be out of box for awhile. It took my repairman 2 hours. Ugh! And I think it still isn’t right. It’s not tight to the plastic rim. Thanks awesome video!

Great video. What part # or model is that? I have to replace mine and it looks just like that one

Thank you, for this "Easy to Follow, Very Helpful Video!😎"

This video is so well done that it gave me the confidence to get the tools to do it myself. Silly questions from an absolute 1st timer: 1) how do I know if I need to replace it 2)are all the screws the same all around or do I need to worry about keeping each one separate? 3)Same question about the big wire clamps: is the spring on the front one that you pointed out also there on the back one?

Thank you. This was extremely insightful.

This video is amazing - incredibly thorough - saved me 100s of $$$ - thank you!

Fantastic instructional video

Exceptionally well described, thanks for posting!

Does this tutorial work for most Samsung washers?

Fantastic step by step video

Fantastic video, thank you!

Solid walkthrough!

Great video, thank you.

Hi Matt, thanks for the awesome videos and your explanations are very helpful. 👍 You rock!

Great video, so now my detergent container assembly is filling up with water. How do I remedy this?

About to do this. Thanks soo much for the video

You guys are awesome. Thanks for the great work

What if I have a stacked washer/dryer and don't have access to taking the top off? My door boot seal is quite moldy and dirty and Id like to replace it

Anyone know the model number of the washer itself?