How to save money and change injectors yourself on an on AUDI Q7 3.0 TDI

Подписаться 558

Просмотров 21 тыс.

50% 1

I saved 5K EUR !
The injectors at the official dealer cost 1300 EUR per unit (CCMA engine). Their installation and programming costs about 300EUR. But if you buy injectors directly from BOSCH supplier (without AUDI label), and change injectors yourself, you can save about 5K EUR.
If you're looking for a step-by-step guide on how to replace the fuel injectors on your Audi Q7 3.0 TDI, then this is the video for you! In this video, we'll walk you through the entire procedure, from beginning to end. So if you're looking to fix your Audi Q7's fuel injection problems, then this is the video for you!
At the end of the video we showed how to adapt the ECU for new injectors.
#diy #audi #autorepair #Ауди #авторемонт #vcds

Опубликовано:

18 сен 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@marcoaurelio6941 3 месяца назад

You are one of those guys. real one! cheers

@blackforestrc1402 7 месяцев назад

perfect Video...great man...thanks

@dusanmaslarevic561 7 месяцев назад

Great video, straight to the point. 1 of those videos where any question would be simply redundant. Still, Ive got 1, what kind of spray is that 1 u used for the o-rings. I'm assuming some silicon spray etc? Cheers, thanks

@D-Stealth 7 месяцев назад

Yeah, it was silicone spray. It was needed here to keep the rubber o-rings from biting. To be honest, I used a thicker silicone grease on the last injectors to lubricate the rings. Otherwise the nozzles would not fit properly.

@peters7141 4 месяца назад

Nice vid but may i add recommendations 1.use original or bosh seal sets 2.if ussing old brackets that hold down the injectors torque the nuts to 10nm if ussing new torque to 9 nm. Overtorque may lead to damaging the copper seals.

@D-Stealth 4 месяца назад

Hi! Thanks for your comment! Of course the seals must be new. In this case, the injectors were already supplied with copper sealing rings.

@R_e_l_a_x_z_o_n_e 7 месяцев назад

Hi, you removed copper washers do you need to put them back? Also for VCDS what interface you are using?

@D-Stealth 7 месяцев назад

Hi! It is absolutely necessary to use NEW washers! In my case, the new injectors had copper washers. What do you mean by interface? Port, cord, CAN?

@loubakker5049 5 месяцев назад

Thought the same.

@D-Stealth 5 месяцев назад

@@loubakker5049 thought about putting the old washers back on?

@thevinylwrapper 7 дней назад

hey mate, whats the fuel consumption like after replacing them? Did you code them as they were new? I assume you wrote down the codes of the previous ones and the codes and position of the new ones to code later on? Thanks for the video! Going to dive into mine soon. My consumption is also too high :(

@D-Stealth 7 дней назад

Hi. I photographed the injector codes before installing, and then coded in VCDS. The codes are normally visible after installation. My fuel consumption went down, but not much. I think the previous owner did a bad chip tuning. I will re-flash to the original firmware. Maybe I will make a video.

@thevinylwrapper 7 дней назад

@@D-Stealth nice. My 4L does 10/100 highway and 16/100 city driving. all the people I know driving 4Ls do 7/100 highway and 11/100 city driving. my previous 4L used to do 8.5/100 average. this one now is too heavy on fuel for my taste (especially as I deleted dpf and egr and remapped) lets see what it looks like when I replace the injectors. thnks for the video mate! cheers.

@user-dx9fr8gw2b 7 месяцев назад

If you take it same injector from the car just to take it out to change the sleals and put back you need still reprogramming ?

@D-Stealth 7 месяцев назад

If the injector has not been disassembled, and it is placed in the same cylinder, there is no need to program. The engine block will apply the corrections it has previously learned. It is required to program new, remanufactured, or from another machine.

@Hasohaso9 5 месяцев назад

Vi imate fabricku manu na povrat goriva iz rail sine na taj motor potrebno je da se prepravi da bi taj motor radio kako treba

@D-Stealth 5 месяцев назад

HI! I have a CCMA motor, I haven't heard of a fuel return line problem on it. Anyway thanks, I'll check it out.

@cristianchile5316 4 месяца назад

Y como se sangra el circuito?????? Yo saque esos inyectores y los desarme , botaron todo el diesel y ahora no he podido encender el motor , como saco el aire del inyector?

@D-Stealth 4 месяца назад

HI! If you change the injectors, there's not much air. You can turn the ignition on a few times and then crank the starter for about 5 seconds and it will start. What made you take the injectors apart?

@cristianchile5316 4 месяца назад

@@D-Stealth ya ok muchas gracias , Se probaron en banco de prueba y todos inyectores están buenos, se limpio toda la admisión, se cambió actuador del turbo, se cambió cuerpo de aceleración, se cambió flujómetro, se elimino dpf físicamente y en la computadora, el problema sigue , humo gris en ralentí y a bajas velocidad, con alta velocidad el problema desaparece .. 🤦🤷

@cristianchile5316 4 месяца назад

@@D-Stealth ru-vid.com__PDDJzMlPo?si=5_3smU2GeAzYpOdd

@D-Stealth 4 месяца назад

@@cristianchile5316 Hi! What does gray smoke smell like? If you put a piece of paper in the smoke, what kind of traces does it leave? 1. Is the crankcase ventilation system intact, not clogged? 2. Is the EGR valve OK?

@600barron 2 месяца назад

Who wants me to fly them to San Diego for Spring Break to do this for me on my Audi?

@D-Stealth 2 месяца назад

Easy, but the tickets are on you :)

@600barron 2 месяца назад

@@D-Stealth no problem. Where do you want to fly in from?

@D-Stealth 2 месяца назад

@@600barron I'm from Latvia.) Come on, I'm just kidding :)

@marcoaurelio6941 3 месяца назад

why did you changed those by the way

@D-Stealth 3 месяца назад

Consumption in the city 28l/100km. And the injectors are ringing.

@marcoaurelio6941 3 месяца назад

@@D-Stealth 28l/100km mentioned on the dash? or the dash said lower values even though you were aware that it was consuming more?

@D-Stealth 3 месяца назад

@@marcoaurelio6941 The dashboard indicated from 25l/100km to 30l/100km. On the highway it showed 10-12l/100km. Bench test of injectors showed that all of them were leaking. The injectors are not repairable. We had to buy new ones.

@marcoaurelio6941 3 месяца назад

@@D-Stealth Thank you for that information. how much were the Injectors directly from Bosch? and by the way which engine is this? CAPA 1st gen or 2nd gen? from which year is the car?

@D-Stealth 3 месяца назад

@@marcoaurelio6941 310 Eur per injector. I have a CCMA engine. 2010 model year.

@pr1sm55 3 дня назад

Missing: You did not show viewers that it's important to use some injector grease for the copper washer to keep it from falling. Also, big mistake you made in your video: DO NOT TIGHTEN THE NUTS FOR THE PRESSURE PLATE IN ONE GO! That's crazy. You need to tighten each nut maybe 45 degrees, even better 25 degrees for right then 25 degrees for left and so on. If you tighten the nuts one side all the way, it can damage the shaft and wedge the injector in not perfectly straight.

@D-Stealth 2 дня назад

Hi! the new copper washers on the new injectors are tight. There is no need to use grease. Actually, if the washers fall off, it means that the end of the injector is burned out and needs to be replaced. That's what I was told at a special service for diesel injector repair. Anyway, I was showing how I install the NEW injectors. Regarding installing the spring clip. I checked the service manual and found no tightening instructions other than nut torque. And it is 9 newtons per meter. The clamp cannot bend the nozzle because the nozzle is in place and the clamp just holds it in place. In any case, if you can tell me in which service manual you saw this field for CCMA engine, I will learn it with interest.