How to service a Landcruiser 100/ 105 1HD-FTE, 1HZ, 1HD-T

Подписаться 3,5 тыс.

Просмотров 141 тыс.

50% 1

How to service a Landcruiser 100/ 105 1HD-FTE, 1HZ, 1HD-T
Same process can be followed on the 80/ 70/ 73/ 75/ 78/ 79
Part numbers:
Oil filter will fit all cars with these engine. Fuel and air filter are specific to the 100/105.
Click this link here to check what Ryco filter suits your car:
www.rycofilters...
Ryco:
Oil: Z334
Fuel: Z252X
Air: A1407
Toyota (Genuine):
Oil: 90915-30002
Fuel: 23390-64480
Air: 17801-17020
Oil type: 15w-40
I recommend Caltex Delo 400
Oil Capacity: When replacing oil, always check the dipstick when filling up so you don’t over fill your engine!
1HZ
Drain and refill: 9.3L
1HD-FTE
Drain and refill: 11.4L
1HD-T
Drain and refill: 11.4L
Oil Filter removal tool for genuine filter: 09228-10002
Tools required:
14mm socket
Ratchet and extension bar
Oil Removal tool
Multi Grip pliers
Funnel
Bucket or pan to catch oil
Air gun/ compressor if reusing air filter.
Facebook: / danvscar
Patreon: / danvscar
Instagram: / danvscar
Like, share, comment!
Let me know what you think or want from this channel

Опубликовано:

6 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 149

@jaisingh2271 7 лет назад

I have been a mechanic for 13 years and dnt recommend using tools to tighten filters as they can cause issues for the next person that services the vehicle also puts a lot of stress on the seals of filters not recommended otherwise great diy video for those wanting to tackle the job by then selves also don't forget to use engine oil flush for those wanting the best out of their engines

@DanvsCar 7 лет назад

Thanks mate, only use the tool to give the filter a slight tighten. I also dont recommend going crazy on it. If you only do them up hand tight and 4wd on corrugated road, its possible for it to come undone. Id rather take the extra step to make sure its firm. (in the Toyota service Manuel there is actually a torque setting for it) Ive worked on cars which I had to shove screwdrivers through as it was done up to tight. (back then I was using a belt tool to undo filters, so they always got crushed, now I mostly use the sockets type). The oil flush is a double edge sward, its good that it cleans your engine, but bad if your engine is not well maintained. It can loosen large lumps of carbon buildup/ sludge and block the oil pickup/ oil passages. If I do a flush on a car i know is not well maintained, I do a few oil swaps after the flush, helps remove any big items. Sometime its better to leave it alone! or you cause more issues/ cost for the clients.

@yandel7092 3 года назад

Instead of putting engine oil on the O-ring, put some silicone grease and tighten the filter 1/8 hard after contact

@i-am-that-what-i-am 3 года назад

No tools tighten... What a TOTAL load of rubbish

@AquaMarine1000 Месяц назад

@yandel7092 I used this once and at the next oil change the filter was almost impossible to remove. It was stuck hard.

@AquaMarine1000 Месяц назад

@@i-am-that-what-i-amI argee, tools make the job easier. A filter has a recommended torque angle after the gasket touches. I always following the recommended specifications by marking the starting point with a ink pen. This might sound pedantic but this verifies the correct torque angle. Cheers

@surfer4hire 11 месяцев назад

Just received a Japanese import LC100. My maintenance experience has only been with the 1HZ 76 series. This is exactly what I've been looking for. Thanks!

@jonss1948 4 года назад

Just a tip. When you're filling from a large drum, put the outlet at the top of the drum to reduce glugging. Filling lawnmowers benefits from this as well.

@mountainconstructions 6 лет назад

How did I miss this video? Fantastic Dan, can't thank you enough for your informative videos. So many 1HD-FTE's out there, and your channel seems the only one addressing them.

@DanvsCar 6 лет назад

Thanks mate. Lots of people are scared to work on them. But with some guidance im hoping to fix that :)

@mountainconstructions 6 лет назад

Dan vs Car Wih the fuel filter I placed an old rag below, then slipped a plastic shopping bag around the filter. Spun filter off, all diesel and filter caught in bag Not a single drop of fuel on me or the vehicle

@DanvsCar 6 лет назад

Good idea! Ill give it a go next time. You can also use the water drain tap on the bottom and connect a little hose to it. Just make sure to you remove the fuel hose from the tank!.

@gerrittkaufman 3 месяца назад

Cheers from Colorado, USA. Thanks for the great video! Will be diving into my '98 HDJ-100 service soon!

@DanielTejnicky 4 года назад

Graphic: "Sir, how EPIC do you want me to make the intro for you?" - YOU: "YES"

@DanvsCar 4 года назад

🤣🤣🤣

@aussiebevo103 7 лет назад

With the fuel filter you can fill it up with diesel before installing it back on the car so you don't have to prime it, because that can take a long time sometimes especially if you have a low fuel level in the tank too

@DanvsCar 7 лет назад

+Aussie Dude85 I have done that before when the primer couldn't suck up any fuel. But it's messy.

@TheBlazen001 6 лет назад

and also he don't need bleed it.will start.

@benjohnston8665 4 года назад

Thats bad practice bro just bleed em go hard or go home

@i-am-that-what-i-am 3 года назад

Yeh, and fill the filter with possible contamination from unfiltered fuel... fekken ameteur. Fix the damn primer pump. If you did that crap at a CAT dealer you'd be sent to the gulag for re-education.

@aussiebevo103 3 года назад

@@i-am-that-what-i-am 😂😂😂😂😂

@jioje7 4 года назад

Really appreciate this mate. Giving it a go on mine in the morning.

@GurjinderSingh-kf4yh 6 лет назад

Well, I dont even have a 100 but i’ve watched all your vids.

@DanvsCar 6 лет назад

Hahaha. Thanks mate, worth the watch I hope?

@tonybreeze8516 4 года назад

And a final shot of you filling in the service manual with everything you've done!

@jameshayward1223 Год назад

Blowing that dust straight into your tappet cover,good idea!

@graemeakerman9120 4 года назад

Fill the new fuel filter with clean fuel before installation will make it quicker to pump up pressure

@i-am-that-what-i-am 3 года назад

yeh, and fill the filter with possible contamination from unfiltered fuel... fekken ameteur.

@carloecleo7635 5 лет назад

Great video. I just bought a 70 series with 1hz engine. I can now DIY. Thanks!

@DanvsCar 5 лет назад

Awesome!! Thanks mate, the engine is a tank, but a little slow. It will never let you down.

@gzahnd 5 лет назад

Super helpful video for a newb like me. Thanks.

@urbanturbine 4 года назад

Surprisingly small oil filter for a turbocharged 4.2 engine.... Yall Aussies are so lucky to get these diesels down under.... We never get Toyota diesels in the USA. Only if they are over 25 years old.... and then you are on your own to understand and take care of it.

@Lee-astrololee Год назад

Love this video, very imformative useful, well demonstrated information, enought to enable the viewer to have a go at doing this themselves!

@slow_diver 6 лет назад

I like your vids. Nothing new, but I can just watch.

@DanvsCar 6 лет назад

Thanks mate, its hard to reinvent something which just works. Trying to help out the average DIYer so I try and keep it simple and show most steps :)

@asad4310 4 года назад

I have a 1HD-FTE when I fill it up 8 litres with the oil filter and check the dipstick it shows full then when I drain 8 litres and Add 10 litres on the next oil change also change the oil filter it shows near empty on the dipstick so I had to add 0.7 litres more totalling in 10.7 now and it shows more than full in the morning as you said it need 11.4 litres so when I start the engine and it warms up the oil then again go to a point on full. How can it be full if its 10.7 litres filled and the full capacity is 11.4 and what was the situation before when it showed full on 8 litres can anyone guide me it would be a great help Thank you buddy for making this guide

@SamoanKiwi 7 лет назад

Good job mate, good tips for my FZJ105. looking fwd to other DIYM Cruiser vids

@105wielki 7 лет назад

Samoan Kiwi Thanks for the comment, i will have to do a video on a FZJ105 and the UZJ100. just trying to find time to get more vids done.

@DanvsCar 7 лет назад

+Dan J whoops commented with the wrong account.

@tealy124 4 года назад

I know this is an older video now, but still obviously relevant to the engines it relates to. I really appreciate the videos, as it gives me plenty more confidence to work on my rig. I have a low kms '05 Sahara FTE that I regularly service. I've been trying to work out why my air filter sensor light comes on the dash when i'm giving it some berries. The old air filter I replaced (was pretty bad but not horrendous) gave instant extra power and you can tell it was breathing better and using less fuel. It feels great, smooth, and faster but the air filter dash light still comes on under medium to hard acceleration. Any ideas? I'm stumped. Only thing I can think of is checking if line to turbo or line into engine has blockages, or junk? Any ideas? It has me buggered

@DanvsCar 4 года назад

Hello! Must be a blockage in the intake. Do you have a snorkel? Some animals like to make nests inside the intake, so have a good look around.

@madvk308 6 лет назад

Appreciate your videos mate, keep up the good work. Look forward to learning more so i can tackle stuff on my HDJ100 Mick

@DanvsCar 6 лет назад

Thanks Mick!

@lookinglassdca9174 4 года назад

Great vid mate well done.

@PaulMotu 7 лет назад

Hi Dan. Good vids mate and want to encourage you to keep doing them. Content and coverage is good so far so keep it up and don't change what you're doing (unless it's for the better - but hard to beat what you're already doing!) How long do you reckon before you'll get onto doing a service on a 200 series so I can start learning how to service the bloody thing. Useless user manual limits me to topping up the oil, checking coolant level and detecting oddities and then bam ... get in touch with the dealer!! Grrrr. But your articles and depth of coverage are good mate so keep it up. Where are you based?

@DanvsCar 7 лет назад

G'Day PaulnSans, thanks for your encouragement! Keeps me wanting to make more vids when I get comments! I have a few friends who have 200s, Ill have a chat with them and see if I can make a video on one. There is a 200s what ill be doing a walk around on sometime this year as well (neat and well kitted out). Yes the provided user manual is only good for basic checkups and how to use functions, would be nice if they had some decent information though! I try and include as much information as possible, it takes a long time to make these videos, edit and type up the informations. Not easy doing it all on your own! (this is why it takes me a long time to upload content) Im based on the Gold Coast (australia)

@PaulMotu 7 лет назад

I'll keep an eye on the channel mate and when you get a 200 then all well and done. However, you've got your beast to keep working on and there are many who would like to see you do more on that. I'm just being selfish hahaha. Don't stress about the time it takes mate. I understand that, but you explain your stuff well all the way through very nicely. QUALITY rather than QUANTITY is what you've done so far and so should be your ongoing performance standard and that's how you'll make a quality channel for yourself. Good luck with getting more Patreon supporters mate! Try and see if you can build some of the work around highlighting certain tool brands perhaps and therefore try and build partnerships with those companies eg Snap On and also suppliers of parts eg Super Cheap and approach them with a view to seeing if they'd be happy to become commercial Patreon supporters in return for your using their products and services. Just a few thoughts mate but good luck and keep it up!

@DanvsCar 7 лет назад

Yes lots to do on this car! Have some rust to fix so will be showing how to repair and respray as well. Nothing wrong with being selfish haha, give me ideas on the kind of videos to create (have so many planned not sure where to start) Lots and lots of custom wiring needs to be done for the rear draw wiring as well (Might come in handy for you). Once I get a few more subscribers ill be hitting up all the big parts suppliers around here, I have made some friends in the industry so hopefully they can help me out (business don't like to help unless they get something out of it as well) But thanks again, good to have a chat with a fellow enthusiast.

@muhammadalwyf4092 5 лет назад

reallt nice video, thank you for helping me 👍

@GB-cm6yy 7 лет назад

Fantastic video Dan...very informative and great detail. Keep them coming please.

@DanvsCar 7 лет назад

+George B G'day! Thanks for the comment, I have a EGR block/ delete, intake clean and catch can install video on the way! Have been editing it for the past few days. Keep an eye out for It!

@goatmcgregor8951 7 лет назад

Man I wish I had your job, I’d love to work on these beasts all day. I suppose it would get old like any job though

@DanvsCar 7 лет назад

Worst part about working on 4wds is the mud.... no one every cleans their car before bring it to the workshop! Another thing is, yes they are big car, but they dont always give you room to work on things! Just as bad to work on as a friken yaris. But i much rather work on one of these then any other car.

@PLxFTW 4 года назад

I've read that some people change their filter and oil at different intervals? I assume that you can just remove the oil filter no problem since it's on the top of the 1HZ? I have to reseat my filter because the dealer messed it up and it's leaking a little from the filter.

@willmoji6779 2 года назад

Great post mate. the 1HD-FTE engines are rated for CF4 in the factory manual. Does it matter if I use the newer ones like API CI4, CJ4 or CK4 oil specs?

@chalovanton 4 года назад

thank you!

@jamiemula4174 4 года назад

Thanks Dan, awesome mate

@BorgCreations 2 года назад

Hi Dan thanks for your videos 🙏🏻 where can I get a maintenance schedule? I can't find it anywhere? Looked on forums, toyota site and manuals but no luck. Want to keep on top of things and make sure i I don't forget something.

@azaelrodriguez2677 Год назад

Gracias, desde Panamá 👍🏾👍🏾👍🏾

@BriggsMower 7 лет назад

with the ryco z252x they recomend on crd to use a z699 cause they filter better also that aircleaner is clean compaired to some we see at work and why didnt u wash it its a washable air cleaner

@DanvsCar 7 лет назад

Had washed that filter twice before, time for a new one. (that car has never seen a dirt road!) Would rather replace it then falling apart and busting up the turbo. Will give the Z699 a go on my 1hz, I will check out the micron rating as well, not good having it to fine as the pump could struggle supplying enough fuel. But im willing to test it out. Cheers!

@BriggsMower 7 лет назад

no probs yea twice is probs a bit for the air filter

@bubbachuck9186 5 лет назад

I didn’t even know I had to service my 98’100 series,it’s bulletproof and I’ve never had problem 1 yet...just kidding😃

@DanvsCar 5 лет назад

😂

@markwhiting8259 2 года назад

Do you rate the ryco filters? I see you mentioned them in the comments. Have you ever cut them open to compare against the genuine filters?

@moetezskouri2785 5 лет назад

i liked everything but the jeep t-shirt

@DanvsCar 4 года назад

Im working on that!

@carloecleo7635 5 лет назад

Hi Dan, which engine is better for daily drive? 1hz or V8 diesel? Average 30 to 40 kilometers per day mostly city driving. Reliability is also considered. Thank you.

@DanvsCar 4 года назад

V8 for sure! Its a solid engine with lots of power.

@i-am-that-what-i-am 3 года назад

V8's cost a lot more to run, not just in fuel costs, but maintenance costs are astronomical in comparison.

@mgneville 3 года назад

Are the maintenance procedures the same for hzj77? I assume so, you include 70 series and 1hz but I'd just like to confirm.

@deant6627 2 года назад

Hi Dan, on the FTE do you need to use an engine flush additive at every oil change and if not how often would you recommend or is it even necessary at all?

@michaelsukoi3007 8 месяцев назад

How to. Install camshaft on a 1HZ engine

@chrisblake5924 6 лет назад

Hi, is there any benefit to filling the oil filter with clean oil before installing it?? I have always done it and noticed you didnt, am i just making a mess for no reason?

@DanvsCar 6 лет назад

Hello Chris, On the 1hz/ 1HD-FTE engines, there is no need to fill them up. Just makes a massive mess and that about it. If you service the car when its hot/ warm and start it straight after you replace all the bits then its even better! Less wear and tear when its warm. There will be residual oil in the pump and oil in all the components. I only fill filters if they are not mounted to the block or mounted facing down. If you are worried about it, you can flick the key a few times (without starting the engine) and this will also prime the filter. With a 1hz you can pull the glow plug fuse and spin the engine a few times. 1HD-FTE there are also ways of shutting the injector pump off. But not worth all the effort. Hope this helps!

@EdgeMasterPro 4 года назад

Dan vs Car 1HZ in a Toyota Coaster here. Not pulled the glow plug fuse but have pulled the relay it just fires up or do you do a few quick flicks of the ignition.

@DanvsCar 4 года назад

You can do a few quick flicks, but the oil pump needs rpm to build up pressure to move the oil. If you dropped the oil quickly then started the car within 2hrs of your oil/ filter change. There shouldn't be any excess wear as all parts are still lubricated.

@thegadabout 3 года назад

Top job mate, shame about the shirt 😂

@Nutzietheclown 7 лет назад

Would you be able to go a guide on replacing wheel bearings?

@DanvsCar 7 лет назад

Hello! Front or rear?

@Nutzietheclown 7 лет назад

Preferably front

@DanvsCar 7 лет назад

I replaced my front wheel bearings and rotors last year, ill try and find someone who needs it done.

@Nutzietheclown 7 лет назад

That would be great thanks heaps! You should do more guides on landcruiser repairs!

@DanvsCar 7 лет назад

No problem, im trying! Just got a lot on my plate at the moment. Unfortunately it take many hrs to make these videos. If I could get more patrons that would mean I could take a few days off a week and make more vids. (Thats the dream anyway!) I need to do the rear bearings on my car fairly soon. Its a similar process the the front.

@serviceinjectordieselcommo3025 4 года назад

Nice

@emersoncesar9066 2 года назад

How many liters does it take ?

@zzyzxyyxp4542 5 лет назад

why you installed the oil filter empty, why don-t fulling it oil before installing?

@DanvsCar 5 лет назад

As you will make a mess. The engine grabs oil pressure quickly so its not something which needs to done. If the filter was fitted in a vertical position then I would fill it.

@TheFirearmEnthusiast 4 года назад

Have a metallic pinging noise consistently every half second? Anyone else have this issue 1hdfte.

@luqmanrahimhf 4 года назад

Hello sir, I heard 100 series is more electric and hence is not easy to repair and have high maintenance cost in comparison to 80 series that is simply and easy to repair. Is that true ?

@DanvsCar 4 года назад

The injector pump costs slightly more to service yes, other then that, very similar price.

@luqmanrahimhf 4 года назад

Thank you friend, for your response. I am planning to buy one for next 10 years. I hope 100 series will work well 😊

@kaitlinhoskins2908 3 года назад

Hi, I have recently bought a 2000 1hz 105 series cruiser with 380,000k.. I’m wanting to do a service tomorrow but not sure on what oil. I have bought Penrite HPR diesel 15 - semi synthetic, 15W-50 (extra 10) would that be fine to use? Cheers

@kaitlinhoskins2908 3 года назад

Thanks for the great video by the way 👍

@DanvsCar 3 года назад

Thats what i used last service on my 1HZ 👌

@kaitlinhoskins2908 3 года назад

@@DanvsCar ok, thanks heaps! Roughly how many litres?

@DanvsCar 3 года назад

Roughly 9.3L, park it on level ground. Check dipstick until reading correctly. Turn car on and recheck.

@kaitlinhoskins2908 3 года назад

@@DanvsCar thanks heaps mate, you’ve been very helpful 👍👍

@GMVlogs16 4 года назад

Hey. I have 1hz engine diesel and I have poured in 9.3 litres and still my dipstick has barely touched the oil in the bottom. So it safe to pour in more oil in the engine ? To make the oil level correct as accordingly to the dipstick. I have checked all the leakage points there are 0 leaks so yeah but still I am stressed out about the engine oil capacity and I did change the oil filter to so please do help me. Thanks

@trevorsmusamba4501 Месяц назад

Keep pouring up somewhere 12.5 then check your stick

@abdulgheyasmajeedi676 6 лет назад

it is esey to open the cap of the filtter

@DanvsCar 6 лет назад

Filler cap for what part? The oil filler?

@abdulgheyasmajeedi676 6 лет назад

but how can you well grees the propeller shaft there is no right place for to lubricate the car

@DanvsCar 6 лет назад

There are 3 geese nipples per shaft. 1 on each uni joint and 1 on the slip joint. If it has aftermarket unis, some of them have no greese points.

@gavinsmith28 3 года назад

Thanks, I’m looking at buying one - would a 2004 100 series with 1HD-FTE and FSH but with 435000 km be likely to last much longer?

@cammitchell5049 3 года назад

As long as its looked after ul get many more years

@alexvandeveerdonk3142 3 месяца назад

Yeah probably another 10 years.

@freeman166 5 лет назад

Love your all your videos but Don't like your t shirt🤪

@DanvsCar 4 года назад

😂 Yes, after this video I Burnt the shirt!

@1khanniazi 6 лет назад

Hi Dan How R u? love to see ur videos. Can U help me about my 80 series LC 1992 D Manual? guide me about its engine. which engine would be perfect for my lc from thes 1HD-FTE, 1HZ, 1HD-T??? and which engine will be perfect with auto tranmission plz guide.

@DanvsCar 6 лет назад

+khan niazi Hello mate, going Well!! Busy busy!! So best engine for reliability is the 1HZ. Best power/ reliability would be the 1HD-T. Then 1HD-FTE is a monster with power, but it is electronically controlled so it's more prone to have electrical bugs out bush. To be honest 1HD-T is the best of both worlds and is plug and play in your 80s. (Also much cheaper then the 1HD-FTE.

@1khanniazi 6 лет назад

Dan vs Car thanks alot for ur help. I really appreciate your work. keep on doing it. can i convert Manual into Auto transmission? will it run perfect with 1HD-T and tell me about the auto tranmission model or anything regarding. plz guide.

@DanvsCar 6 лет назад

Got a few vids in the editing stage!! Yes you can convert from manual to auto. You will need a few parts to do the conversion, transmission mount, shifter/ surround, peddle , wiring, transmission, torque converter, flex plate and a auto radiator. Now you have 2 gearboxes to chose from, the 4 speed and 5 speed. 4 speed is going for towing and 4wding. But gets hot so I recommend putting a cooler on it. 5 speed is also good for towing but better for hwy driving. I would recommend the 5 speed auto. While your there also install a cooler to help with performance. A lock up switch would come in handy as well. If you join a forum called "Lcool" (is a forum for all Landcruiser owners) it has a lot of information about the conversions.

@rufaelsolomon8395 5 лет назад

nice video###

@divyasri8696 5 лет назад

Hi sir for LC 100 i have replace all 4shock new but hight conrol is not how refix it frist hight was working pls tex me sir

@DanvsCar 5 лет назад

Hello, just confirming. You have replaced all shocks on the car which has 'high adjustable' suspension. But it does not work anymore now? You need to check and see if you have any error codes with an OBD reader. It could be sensor, cable or a few others things.

@1987yuksel 7 лет назад

Dan vs Car Hi how often we need to change automatic transmission fluid and fuel filter ?

@DanvsCar 7 лет назад

1313AslanBey hello. if it's the auto box on the 1hd-fte it is a sealed unit. I'm currently camping and will check the service intervals. can you confirm your engine please? With the fuel filter it depends on the fuel quality in your area. Usually every 10,000km is what I recommend.

@1987yuksel 7 лет назад

Dan vs Car hi thanks for reply. I have a 2007 4.2 TD 1hd-fte engine

@DanvsCar 7 лет назад

Here is a good reference document for service intervals. 40,000km is recommended. www.lcool.org/technical/100_series/service-specs-100series.pdf

@1987yuksel 7 лет назад

Thanks mate

@catco01 4 года назад

Those models don’t ever need the auto trans fluid changed. I’ve had mine for 16 years never touched it and still bright red and no issues. It even says on the dipstick not to change the fluid.

@freedomfighter8945 7 лет назад

Hi Dan great video thanks for sharing. Just have a question if you can help with I have a 2006 landcruise 100 series deisel 1HD-FTE and its automatic transmission. I have a problem shifting the high range lever it is stuck in high. I have tried lifting up rear of the car to release tension on gears and tried to move lever no luck. Can you give any ideas on what to do. The truck is not a full time 4wd. The lever is high range neutral and low range. It has a short shaft that goes on top of the gear box and has four bolts holding it. Any help would be appreciated.

@DanvsCar 7 лет назад

Hello! Sorry I didnt get a notification about your comment! Ok this is a common problem with the toyota transfer cases. If the Hi/Low range stick is not used for a long time they do become "tight". As you mentioned it has 4 bolts holding it down, we remove those, remove the stick and WD40 the inside. This usually helps, put the stick back in and cycle through high, neutral and low. I cycle throw mine at least once a month to prevent this from happening. If this does not help let me know and ill give you a few other things to try. Cheers (Y)

@freedomfighter8945 6 лет назад

Thanks Dan it's been fixed I had to pull the lever off completely and pull apart and move leaver while in vise using wd40. Then used some small amount of grease. It works perfect now. It was rusty before. After having got it to move I cleaned all rust and greased it up and now it's perfect. Thanks again for your reply.

@DanvsCar 6 лет назад

Great to hear! Every week move the stick a few times and this will stop it from happening again :)

@melnikov86 Год назад

Там где находится вал-пустая полость, я забил эту полость смазкой для подшипников, теперь вал не будет ржаветь никогда. 👍

@krissie7076 6 лет назад

Can you help me to check the diameter of 09228-10002?

@DanvsCar 6 лет назад

I will check for you when I go to the workshop next.

@krissie7076 6 лет назад

Thanks a million

@DanvsCar 6 лет назад

Finally got it! Its 99mm with a vernier caliper

@krissie7076 6 лет назад

Thanks Dan, I couldn't get hold of the Toyota version but found the made in Japan KTC AVSA-099

@MrBmw323turbo 7 лет назад

dan the man....can you maybe help me my 1 hd fte has no power and scan tool shows no errors...new diesel filter new timing control valve everything seems to be fine but no power

@DanvsCar 7 лет назад

The one and only! Are you getting a engine light? manuel or auto? does the RPM go over 2500? Need some more info please! How many km has the car done, is it well maintained, have the injectors been done, hand any turbo work, did you pick up any dirty fuel. Cheers! Dan

@MrBmw323turbo 7 лет назад

no engine light engine revs up fine vehicle has 260000km on the injectors have supposedly been done before i bought it 3 months ago and new edu fitted and its a auto and became like this after a car wash turbo is stock and boosting 0.8bar

@DanvsCar 7 лет назад

Does it feel like its engine or gearbox? Could also be the bands in the box slipping. Have you checked your air filter? or checked if anything is blocking the intake? blocked the EGR system? (could be stuck open) Checked to see if any of the brake rotors are stuck? after a drive are the hubs hot?

@MrBmw323turbo 7 лет назад

redone the diesel pump and guess what it is still the same after diesel pump recon....drove well for about 100km no has no power again...wonder if the crank sensor isnt faulty

@DanvsCar 7 лет назад

+James Sinclair could be a number of things. Have you inspected the fuel tank?