How to Setup FS-iA6B with iBUS - Wizard X220 - Flysky FS-i6X (SPracing F3 Flight Controller)

Подписаться 42 тыс.

Просмотров 90 тыс.

50% 1

You can now support RCwithAdam (and gain special perks!) HERE: ko-fi.com/rcwithadam 🤗
Visit my website here: rcwithadam.com/ 💻
Want to connect your Flysky iA6B receiver (Rx) to your Wizard X220 using iBUS protocol! Well here ya go! (iBUS provides a faster communication between your receiver and your flight controller than PPM (though you won't notice it if your brand new to FPV), which is why you may have had people tell you to switch to iBUS).
STEPS:
1. Plug "servo" connector cable into Rx "ibus" servo port
2. Plug other end of cable into flight controller port
3. Set transmitter "Rx setup" to "ibus"
4. In betaflight; set UART3 to serial RX, save
5. CONFIGURATION: serial based receiver, ibus, save.
6.REMOVE PROPELLERS, connect battery, test function in RECEIVER tab.
Ta da!
▶️ Here's the FULL Eachine Wizard X220 setup video I mentioned: • *NEW* Wizard X220 Setu...
COMMENT BELOW if this was helpful and let me know if you have more questions!
#wizardx220 #betaflight
Support RCwithAdam by purchasing through these links!
Amazon amzn.to/2FHjkwI
Banggood www.banggood.com/custlink/Kvm...
I have a website rcwithadam.com/
-------
RC with Adam GEAR
RADIO: amzn.to/2osIur0 www.banggood.com/custlink/3Kv...
QUAD RECEIVER: amzn.to/2CsvX0C www.banggood.com/custlink/v3v...
AIRPLANE RECEIVER: amzn.to/2OBIqnj www.banggood.com/custlink/GG3...
QUAD PROPS (my fav) amzn.to/2DywVXA www.banggood.com/custlink/GGK...
RC with Adam FILMING GEAR
Main camera amzn.to/2pGZA4L
Action Camera amzn.to/3dVW6DE
Mic amzn.to/2OKoCOB
Camera stand amzn.to/2C4I3uX
--------
Mandatory Disclaimer:
I participate in the Amazon Affiliates program, which means that if you click on one of the above Amazon links and purchase a product on Amazon, I will receive a teeny tiny commission (at no additional cost to you). Also, various other links listed here may be affiliate links, to which this disclaimer also applies.
*REMEMBER, always use caution and your best judgement when building and flying RC aircraft, be a good neighbor, and HAVE FUN!*
-----------
About RC with Adam: Adam makes FUN and HELPFUL videos about Radio Controlled aircraft, tech, and DIY projects! #RCwithAdam

Наука

Опубликовано:

21 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 73

@RCwithAdam1 4 года назад

Do you use the iA6B in your quadcopter?

@Floli15 4 года назад

I'm planning to use a FS-iA6B for an iflight green hornet. Do you think that will work? I am totally new in FPV and very thankful for your Videos! Keep on filming :)

@muhammadyahya8392 3 года назад

I do, and i cant get rssi please help, i am using ibus

@SteadfastRC 4 года назад

Adam I literally cannot thank you enough for doing FlySky videos like this oh, it really helps a lot of us out in the community, you are the only one I have found that does these detailed FlySky receiver and transmitter setups it really helps out a lot so once again thank you!

@RCwithAdam1 4 года назад

You are very welcome!! Thanks for the feedback! It really helps to know this is useful to people! 😃

@yatzeegamingop 3 года назад

i like how you explain everything so clearly. Punctuation on important stuff is so good.

@brody48123 4 года назад

THANK YOU SO MUCH I THOUGHT MY DRONE HOBBY WAS DONE YOU HAVE SAVED ME THANK YOU SO MUCHHHHHHHHHHH

@RCwithAdam1 4 года назад

Glad hear it! 😉👌

@NotiAn1 2 года назад

thank you so much ! i've been trying to configure mine for the longest time and you saved me

@RCwithAdam1 2 года назад

Glad I could help!

@JoanMendoza Год назад

Thanks for the guide!

@CarminesRCTipsandTricks 2 года назад

It CAN'T really be THAT easy, can it? This was very helpful, THANK YOU!! 👊🙏👍👍

@estebanjurko2184 2 года назад

Hey man how are you? Wanted to ask about a little issue, i did all the steps and am using the SPRACING F3 and your same Flysky controller, the only difference is that i am using cleanflight but used the same configuration as you and the software shows that the reciver and transmitter work but the motors wont move.. i only make them move by sliding the bars on the motors tab. Also i saw that on the video your motors didnt move at the end.. so what step i am missing? Thanks!

@panzertracks 2 года назад

I assume that it's the same steps to connect an FS--IA10B RX? And do all the channels go through one cable?

@AlvaroGomes 2 года назад

I noticed that at the end of the video when you are using the controls the motors are not working right?

@jacobfurman1629 2 года назад

I DO NOT SEE AN OUTPUT MODE ON MY I6. I cannot find any information either. Is anyone having the same problem?

@Sunnyfpv1617 Год назад

At 4:50 I am motivated now I am just gona keet trying

@eagle7015 3 года назад

Same for the ia10b?

@matty2808 Месяц назад

Hey, how did you get rssi working on fly sky in this video?

@AlvaroGomes 2 года назад

The VTX and camera must be connected to the board for the drone to work

@florinnegoita8846 3 года назад

it's the same with me ... but in betaflight it doesn't recognize the remote control im tyro 129 ...

@a-vinil 3 года назад

Hi Adam, Please help me wire my FS-iA10b receiver to Emax Magnum Mini F4 stack?

@andreiluciantecu9771 3 года назад

why UART3 must have the receiver ON, and not UART1 or UART2?

@cr0vv575 3 года назад

how do i do this on the x220s tho?

@AlvaroGomes 2 года назад

I have this quadX even following all the settings and in betaflight the i6X is recognized nothing happens. Emax Buzz + f4 (firmware omnibusf4) F4 Magnum + FS-i6X + FS-IA6B

@ArgonautasDrone 6 месяцев назад

Obrigado pelo vídeo, ajudou muito 🪽👍

@lyricseditoryt156 2 года назад

Where to find a connector like that?

@CaptainJohn 4 года назад

Cool! Still in the plane gang lol

@gatitomono47f77 4 месяца назад

Hi how could It be done with an f405?

@rami587 Год назад

hello im having a problem with my fs-i6s remote no serial protocol signal i tried many times to do it but not working some guys said that i need to downgrade and then upgrade to the fs-i6x fireware so that it will work i home someone can help me because im really stuck here

@jamesneville441 2 года назад

Can you still use the empty channels on the receiver when connecting this way? I want to add 2 forward thrust propeller's to a quadcopter so basically the quadcopter props are just to make it hover. It will pull forward like a plane with the forward facing props

@RCwithAdam1 2 года назад

Sounds cool! I'm not sure, but my guess is YES.

@jamesneville441 2 года назад

@@RCwithAdam1 trying to make sense of it all, a lot to learn at once lol

@ADVENTUREBORNEO Год назад

Saya punya remote flysky dan receiver, saya mau membuat drone seperti anda, tolong rekomendasi alat apa aja yang dibutuhkan untuk membuat drone

@jimmyfam8832 2 года назад

The spracing v3 firmwear is no longer on beta flight config anymore hellp!!

@Yogman444 3 года назад

is it possible to solder these pins? i dont have that cable and i’m working on a DIY Tyro 119

@RCwithAdam1 3 года назад

Yes, definitely. It might be a bit tricky to get all the solder off later though.

@xxdrvash04ytxx5 3 года назад

do you have to leave that thing in and connected to the drone at all times?

@RCwithAdam1 3 года назад

Hi! Yes, the receiver must always be connected to the flight controller during flight.

@bevinmore Год назад

I had a rxloss error and realized a uart port was disabled by me accidentally. This saved me

@iannicholas6698 11 месяцев назад

Hello I need help.....I can't get the motors to spin after connecting the transmitter with the flight controller.....all the connections are done but can't seem to be working at all

@ZapTeam 6 месяцев назад

Did you figure it out

@smp_rc_2002 Год назад

Is there a way to connect another receiver to the main receiver in a way to extend the number of channels available. for example connecting ia6b to another ia6b to get 12 channels?

@RCwithAdam1 Год назад

That's a good question! I'm not sure, but that would be neat. I would think that might be possible with the ibus port.

@smp_rc_2002 Год назад

@@RCwithAdam1 it would be nice if you could make a video on how to do that if you figured it out.

@davidevanoncini3433 3 года назад

hii, so i did everything like you said on the video and it does actually works when the green thingy is plugged in the drone but when I unplug it from USB and the thingy and try to use the controller motors still don't spin, and for sureee i am missing some steps but I have not clue which one so if you could tell me (if you know ofc) what I am missing I would be so thankful :D

@RCwithAdam1 3 года назад

Hi! When you say "green thingy", do you mean the receiver?

@davidevanoncini3433 3 года назад

@@RCwithAdam1 (wow you are so quick at responding) and yeah, like is the thing you hooked up on the FC so yeah, It should be the receiver (sorry if I am not precise but I am super new at all of this) ow and btw I was searching around and I think I am missing the "rx" like a card that stay on the stack, for receiving the signal, unless it's the "green thingy"

@RCwithAdam1 3 года назад

Yes, the green thingy is the reciever. It needs to stay plugged in and connected to the flight controller at all times.

@RCwithAdam1 3 года назад

Yes, the green thingy is the reciever. It needs to stay plugged in and connected to the flight controller at all times.

@davidevanoncini3433 3 года назад

@@RCwithAdam1 ok I won't unplug it but how can I make the motors spin then?

@thediscoman2001 4 года назад

iv done everythin in this tutorial exept the rx setup on the remote as the options are not there on my remote i am using flysky fs-i6 not the fsi6x any help would be good as im stuck now non of the controlls work

@RCwithAdam1 4 года назад

Hi! Let's try to get you unstuck! Which version of firmware are you using (you can find that in the system settings menu)?

@thediscoman2001 4 года назад

@@RCwithAdam1 2.0 1-feb-2018

@bktechnologies88 2 года назад

Please how can i bind a flight controller that has a built-in fly sky reciever to a transmitter

@RCwithAdam1 2 года назад

Which flight controller?

@bktechnologies88 2 года назад

@@RCwithAdam1 any flights controller that has a built-in reciever and please where can get a cheap transmitter please 👍👍♥️

@sanjeevsebastianmurmu5631 3 года назад

can we use this FC with all in one esc

@RCwithAdam1 3 года назад

I think so, but I haven't done it.

@roshanhettige 4 года назад

how to use naza m lite x1 & x2

@RCwithAdam1 4 года назад

Hi! I'm not sure. I haven't used those boards before.

@nicoolaciregui6076 Год назад

Does de x220 V3 accepts this Rx?

@RCwithAdam1 Год назад

I'm not super familiar with the X220 v3 flight controller of the top of my head, but yes, it should.

@Prop-Fpv 2 года назад

what can i do when my drone doesn´t react to the transmitter

@RCwithAdam1 2 года назад

Tell me more details about your setup and issue you're having.

@Prop-Fpv 2 года назад

@@RCwithAdam1 i updated my flysky fsi6x to a costum firmware for rssi, but it didn't work, so i downgraded it to the original firmware which i had first, but i bound it many times, but the drone doesn't react to any aux channels(switches, sticks), in the simulator its working, when i bind it, the receiver shows, that its bound, but the drone doesn't react, i set all aux switches correctly up