How To Sharpen A Drill Bit Easily | HSS Drill Bit Sharpening 

😂😂 30 seconds on a grinding wheel does it, you don't have to build bloody Noahs Ark.

Safety was not present in any part of that demo it was notvdone properly and Noone should follow his lead.

You left, "easily," behind after the fourth step.

Wow! The idea is so great, congratulations

How to take off a finger. Do not ever hold a piece of metal with your fingers while drilling. Use a vice grip or any other tool. Ask me how I know.

Most of this was painful to watch. Not that hard to freehand once you learn the geometry of a drill. I find it very relaxing to sit down with good light preferably sun light and a pair of magnifiers on and sharpen 50 in one sitting. If im getting technical I'll use a gauge.

Sharpening a drill bit properly really isn't that hard. But that's not it. Look at the small chips. The bit is going to overheat in no time at all. Once you learn the basics you don't need any jigs or angle finders. Freehand. Been doing it since high school, when they taught you real world information

As boiler maker I can ensure you this is stupid I only need a bench grinder and if on site a grinder

Только не нужно забывать периодически сверло охлаждать, тогда будет вообще ХОРОШО. Привет из Гомеля, Беларусь 🇧🇾

Too much bull crap involved. Go buy a drill doctor and get it done quickly. Or simply throw out that dull bit and buy a new one.

Might of never been told this but... you're one sharp guy.

Never have I seen a more complicated way 😢

Still waiting for the easy part

I've been a machinist twenty years,I know how to grind a drill by hand on a grinding wheel,it's a art in itself especially big drills,not many people know how to do it.

It seems that the art of sharpening drill bits on a bench grinderhas been lost.

My friend, you are an amateur. You simply don't know how to sharpen a drill bit, under what angle depending on the metal you want to drill. Only amateurs will sharpen a drill bit on the side of the grinder stone. In this case the drill bit will be sharpen innequally coz a bigger amount of metal will be polished from the right side of the drill bit compared with a smaller amount of metal polished on the left side. More than that, you haven't polished that drill bit on its back, that drill bit will cut 3 or 4 holes and then it will get burned. You better learn more and only then try to post here.

I hold it free hand and sharpen

The chips instead of a drill a spiral piece demonstrates a drill bit sharpened off center. Not east, not good results

Would be much easier to buy a new one. That was a huge time expense.

So I need wood, bench saw, metal, angle grinder or buy a new drill ???

Give me a grinding wheel and I can sharpen in about 30 seconds. A lot of wasted time. Good try

Its amazing man 😮

Think easier and faster, I will go buy a new one!!

How to sqharpen a wood flat bit?

If you know how to, jig is pointless. And with this instruction loads of people will make scribes from drill bits 😅

Yes sir!! Nice in a pinch but needs to be split point especially in steel.

I do the samething at work. But I don't need a block of wood and all that jazz. I just hold it up to a grinder. Use 2 nuts for a guide. Give it back relief....voila! Done!

He didn't grind any relief on the back side of each facet. That drill will make 2 holes, and then burn, losing the temper. If you don't understand what I have said, don't bother with this nonsense, just buy a new drill!

What ever happened to the Drill Doctor for sharpening?

I'd g-clamp that piece down mate or it'll catch you out one day!

I give it a bit more angle and definitely a back relief. Some ofy best drill bits. Kinda gives it a step up

I just use an ANGLE grider, Put the drill bit an a clamp angle myself and sharpen, my bit works really great after and that's it really......

Why not just use and angle grinder with a grinding disc and sharpen at different angles?!

We have dramatically different definitions of "easily". They make drill bit sharpeners. Cheaply would have been a descriptor.

I am confused. Is hands not sufficient to sharpen it with sharpner, why use that wood tighten tool? Is it necessary??

Why was the demo with a different drill bit ?????

If ya wanna lose a few fingers, follow his lead....

Or get a new bit,whichever is easyer

Lmao, did I miss the “easy” part? Just go buy a new bit, if you’re using this week long project method of sharpening a drill bit…

So for a 4 dollar drill I'm out an hour.... Really good video, but not the play for me homie!

I would just use a grinding wheel if need be. If I'm in the shop i just use the thirty dollar drill doctor though lol time is money

How is this easy lol

What a lot of fuss and work. It would have been quicker and cheaper to buy a new drill.

that looks really easy 😂

You didn't explain in what position the drill bit has to be clamped. I refer in terms of rotation.

Stop ..Just put it on your bench top grinder, you'll be finished in under a minute..

You have to be kidding me… All that work just hold the drillbit up to a grinder?

❤❤❤❤

Agreed with first comment, however injeneral good idear. One point however don't ever put metal any were near a sanding disk it will catch the wood dust alight on the bottom side, perfect tinder 😮

who has all this equipment and time to do all this to sharpen a drill bit

No thanks. I will just buy a sharpening machine

Don't follow this ! This is not the way and will be off-center

Your joking right. We just freehand sharpen drills on a bench grinder. You can use a scale to get flutes the same or you can buy drill sharpener guage. You can also relieve the backside. Get some experience and you'll be able to sharpen drills without making all that up.

How about the bit that is used for the "sharpened" test is NOT the one he supposedly sharpened 😂😂😂 It's a larger size and WAYYYYY shorter than the one he supposedly sharpened. Just saying!

Thank you for sharing these useful tips. I applied them and saw immediate results!

Cool but not very easy

My my what a total waste of time.....

Tool box lakdi ka kitne ka hai

Please sharpen your saw blade.

You have a talent my friend please continue to show simple ways to achieve mundane tasks. 👍🏻👍🏻

Love your enginuity and DIY skills! If you're looking for a new idea or challenge... I would love to see if you could design a "pruning shears" attachement for a cordless drill(!?) Happy Holidays / Merry Christmas!

All that for a £1 buy 😂😂😂😂

He is desplaying a lot of scrap instead of getting straight to the point

😂….ok good luck with that.

Bullst

Wait, he needed a sharp drill bit in order to sharpen a drill bit?! 🤣 I'm sorry but I would just go out and buy a cheap little bit sharpening kit and call it a day.

I can sharpen by hand better lol drill was chipping swarf worst example of sharp drill I’ve ever seen!!!

Nice vidio sharing

Which country are you from

This is easy? Ok, if you say so.

Animo...👍.

Good work

I can do it better free hand. This is the hard way.

it's really great. i had a problem drilling steel. maybe you have some answers? there's a 5mm thick general-purpose steel that I had trouble drilling. With a new drill bit, after just 2 drillings, the bit loses its shape. Even when I change the drill bit, nothing happens. I can't drill any more.

Buena idea

Cheaper to go buy one with all that effort

NOTHING ABOUT THIS SAYS EASY TO ME

Your saw needs a new blade