How To Test 3 Pin Primary Ignition Coil DIY

Подписаться 10 тыс.

Просмотров 50 тыс.

50% 1

First set your multi meter to the ohms position and connect one terminal lead to the negative terminal and other terminal to the positive terminal of the coil. If the reading is endlessness, then there is no continuity and the coil is faulty. If the reading is zero, then there is continuity and the coil is good.

Опубликовано:

16 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@ERICAUTOCENTER Год назад

*Thanks for watching and share to reach many people

@gyanato4458 Год назад

Powerful video content keep them coming sir 💯 pure informative

@ERICAUTOCENTER Год назад

Appreciated

@lawsonlavia278 7 месяцев назад

How much a good ignition coil should read

@ERICAUTOCENTER 7 месяцев назад

It depends the type of coil base on the engine capacity whether 3 cylinder, 4 cylinder, or v6 & v8 type but the ignition coil reads from 0.94, 0.01, 0.02 or more and finally some also read from 1.02 or more and all this means there is a continuity which means the ignition coil is good

@nhubui1602 11 месяцев назад

Thanks for the video . ❤

@ERICAUTOCENTER 11 месяцев назад

Welcome

@neostarfromearth107 Год назад

Thank you Eric, nice lesson !

@ERICAUTOCENTER Год назад

Glad you liked it!

@figgiefigueroa7372 4 месяца назад

The multi meter number to be set ????

@lindolphmurray9480 Год назад

Thanks for the video but u need to raise your voice a little so we can hear u more clearly

@machinemods Год назад

Where do I connect the Tachometer wire?😊

@travelservices740 Год назад

sir whould you please reply in vedio that if reading is more then 26.9 means 35.09 or 45.09 then the coil ok or not correct rating of 3 pin ignation coil is what

@ERICAUTOCENTER Год назад

Check in the comments section I have replied many on this same question thank you

@insane_eddie_7257 Год назад

What is the proper reading on a 2006 Chrysler 300c with a 5.7 motor can you help me please

@ERICAUTOCENTER Год назад

Please come out again with your question and let me help with the answer I can’t get you clear. Explain further

@insane_eddie_7257 Год назад

@@ERICAUTOCENTER im trying to test my coils but I don't know the exact readings

@ERICAUTOCENTER Год назад

Oh ok a proper reading must start with 01.0ohms I have done a full video for premier today at 2pm local time stay updated.@@insane_eddie_7257

@aliautomotive 9 месяцев назад

Just checked with brand new coil ,totally wrong readings.showin 1300 to 1800ohms on one pin only.

@ERICAUTOCENTER 9 месяцев назад

Then you can check it well it shouldn't be like that. there should be continuity it is the way you're using your multimeter. Dont delay too much time on the multimeter it will trigger everything and can burn your new coils

@yohaneswoldemichael5117 Год назад

much powa to you

@ericdarko5479 Год назад

Thank you

@ERICAUTOCENTER Год назад

Welcome

@adegokeo.johnson3163 Год назад

Checked mine and is showing 51.6

@ERICAUTOCENTER Год назад

51.6 means there is no continuity the ignition coil is bad. If the resistance show 0.01 on the multi meter this means there is continuity then the ignition coil is good. so have to buy a brand new set of coils