never thought about the bearing needing grease but I have had mine for 2 maybe 3 years and it works great I have cleaned the nozzle. Dont forget to get the extension piece save your back!
I just used this to clean the aggregate around my pool that hasn’t been cleaned in 20 years! It looks new! I couldn’t be more impressed with the ryobi cleaner. I used it with a 3000 psi 2.4 gal Honda washer.
This was a good video and covered all the things that need to be inspected and lubricated. Greasing it is the most important thing that causes them to stop spinning.
Thanks! Glad you liked the video. The problem with these sleeve bearing units is that you have to frequently lubricate, so you have to stay on top ot it.
I had a lot of trouble getting that little brass filter out. It looks like the screw broke off and I basically had no way of unscrewing the rest of the filter. Looks like I’ll need a new inlet plug and filter replacement. Thank you for the video. The rest went great.
I had the same issue. Unscrewing the filter CCW with a flat bladed screwdriver extracted a very short screw, but the filter itself was still inside, and I could not find a way to get it out. The tiny screw went back in readily, so I don't think it was broken. Any ideas how to get the filter body out after the tiny screw is out?
@@roncain9102I don’t man. I just ended up buying a new head for $80 and kept the other one for possible spare parts. Let me know id you find a way. I’m sure I will run into this again in the future. Thanks
Thank you…. I have a Yamaha, very similar and it quit. I followed your directions, greased the bearing and I am back in action. Thumbs up to your channel and advice!
Thanks for the very informational video. I've beem looking everywhere, and your the only one to address the bearing sitiation. I came across a good deal on one of these, but needed to verify it wasnt a sealed bearing. Appreciate it sir.
A hidden gem of a channel! Loved this thorough review. Your knowledge is very valuable to the community, so keep making these videos. A lot of young kids today, make reviews and know nothing! I love your garage organization!!! Subscribed. Thank you for not selling out and becoming a corporate infomercial instead of an honest review. This matters to us. Thank you also for not putting any obnoxious music overlay and keeping it simple and natural. This is professional. I would suggest you get a shirt microphone for good audio. Also make sure your indoor lighting is clear for good visuals. These small changes will make your videos more attractive and not look dated and old fashioned. Look at Humble Road van build videos. The guy, George Mauro was a photographer in his previous career. His superb audio and visual quality come down to simple things - a good microphone attached to your shirt, not on camera, and soft lighting indoors that highlight his project. Mic is costly, but lights are cheap.
Well thanks for the input and the advice. I often worry that I supply too much information because viewers get impatient and exit my video. It's nice to know that some people appreciate it. I recently upgraded my camera, and believe it or not I am researching lapel mics right now. I bought a new shotgun mic and it sounds worse than the cheap one that came with my old camera. I will check out the Humble Road folks. Thank you for subcribing and taking the time to share your insight with me.
I have a Simpson 15” rotary attachment. I got about an hour of use out of it before it was leaving swirls. Switched back to the wand and 25 degree tip. Will try your maintenance fixes and see if it works again. Of course I lost the cleaning wire.
This was a PROPER review. I'm glad you showed how to service it. I was skeptical as I didnt see a zerk fitting to grease it. Maybe next show a turbo nozzle? Lol. But thank you for the review! I bought the Walmart brand to go with my 3200 Ryobi gas PW, and that Cleaner broke in the first use, the plastic failed. So tomorrow I will try this one out. Just bought it!
@Deer Park Home & Shop thank you. The ryobi was much smoother and better. Greased it up and put it away for the next use!. Thank you. Keep up the awesome work!
Thank you Mike! You covered everything I needed to know!! I just returned a Simpson 15" metal surface cleaner but my pressure washer didnt have enough psi & gpm to spin the wand fast enough. I have a Simpson 2700 gas pressure washer, but that 2700 psi is with a jet nozzle. I was looking for a straight forward review of this Ryobi and i found yours. I have subscribed to your channel and liked the vid!! Thanks again!!
I clicked liked because that was a good video but I clicked subscribe because of your organized tools and you were filming at 8am in the morning. AH ha ha
want to save your back when using that surface cleaner get a wand extension I have a 36 inch extension between my wand and the surface cleaner. This allows me to stand up straight while using it especially helpful when doing a long job. Hope you try it makes all the difference in using this without back pain.
Think I solved my question on wheels versus no wheels. If surface perfectly flat wheels may be faster, but if you have cracks, wheels will get caught up reducing speed and possibly damaging wheels.
Hello, I truly thank you for this wonderful video. I do have a question that I hope you can help me with. I just recently purchased the following surface cleaner from e-bay-15" Pressure Washer Surface Cleaner Pressure Washer Extension Scrubber 3200PSI US $36.99. The reason I purchased it was because I own a 2800 PSI gas pressure washer. I always have the hardest time getting it to start so I decided to purchase an electric one. I bought a Craftsman 2100 PSI from Ace Hardware-Craftsman CMEPW2100 2,100 MAX PSI* Electric Cold Water Pressure Washer. I had an old surface cleaner for my gas machine but it will not sin due to the lower PSI of the new electric machine. So I purchased the above surface cleaner that works up to a max of 2200 PSI. So it should work. I used it and the wand did not spin as it should It left circular marks as your video shows. I e-mailed the seller and he recommended I clean out the nozzles. I did as your video showed but have not tried it yet. But after cleaning I sprayed the hose through one of the jets BUT no water came out of the OTHER jet as your video shows. I don't think this has a screen in the middle part? The reason I purchased this surface cleaner is because it is supposed to spin well with this lower PSI machine. My old surface cleaner would not spin with the electric machine because after the fact I realized that the box of that Briggs and Stratton surface cleaner would only work with a MINIMUM of 2400 PSI. So there you have it-- what do you recommend and can you tell me what else I can do to make this e-bay purchased surface cleaner spin properly. It is brand new and only used once for a short while and did not seem to spin well so I stopped using it. Thank you
Try either forcing water through the quick connect on top of the unit and see if you get water out of both nozzles, or remove the quick connect and try the same thing. You have to remove the quick connect to get to the filter if it has one. If you are still only getting water out of one jet, it most have an obstruction or defect somewhere between the quick connect and the jet. If you are getting swirl marks with just one jet, it has to be passing high pressure water through, so it must be working with your pressure washer.
@@deerparkhomeshop2471 How do I remove the quick connect. I cannot see any place from the bottom of the cleaner. And the top looks like a nut or something but it seems really tight? The pellet said to take off both end nozzles and try shooting water thru it. But those nits or nozzles are quite tight as well? what do you suggest?
@@montemag I am reluctant to tell you to muscle these fittings off, because I'm not familiar with your surface cleaner. I was able to remove mine with a wrench and some effort. but I don't want to feel responsible if you damage your cleaner.
@@deerparkhomeshop2471 I understand and truly appreciate you. But do you think with your knowledge that my 2100 PSI machine is OK for what I am using it for and this surface cleaner SHOULD be OK and do the job as well as long as I get it to work properly? The reason I ask is that suddenly when I shop online I find these much more powerful machines that have 3000 PSI for such low prices as $160? Like the PowRyte Electric Pressure Washer, Foam Cannon, 4 Different Pressure Tips, Power Washer, 3900 PSI 2.4 GPM-- that is ONLY $119.99???????(If you would look this up on the site and let me know your thoughts on this machine- seems really powerful?) Mine is 2100 PSI and this is 3900 PSI with a greater Gallons per minute as well and is $80 less expensive? I have 90 days to return my Craftsman to Ace Hardware?? My thoughts are that I can use the Briggs and Stratton surface cleaner that only works with more powerful machine and thus I would not have to go thru the trouble of trying to fix this other surface cleaner. Am I being overly particular about my needs? I really respect your advice, sir. Thank you and let me know what your thoughts on this would be.
Hi. I really liked your video on maintaing the pressure washer disc cleaner. Do you have any suggestions on why my 3000psi Ryobi pressure washer engine pulses while running? It's doesn't appear to be a choke issue or an air filter problem. I'm guessing the gas filter is the culprit but I don't know where it is. Can you help? TIA. Dan
Now, I'm not an accomplished small engine expert, but I do know that there are several reasons this can happen. The unloader valve, pump problems, water supply problems, etc. Here is a link you can check out that will explain it better than I can. www.gardentoolexpert.com/why-does-my-pressure-washer-keep-pulsing-helpful-tips/
I've never tried it. If you do it, I would start with a rug that's not to important to you, because with the pressures involved it could really damage it. Pressure washing is really designed for hard surfaces. If you do it, let me know what happens!
My 12" Ryobi Surface Cleaner worked well during my first use, but on the next use it stopped spinning. I could raise it uo about a foot and it would start spinning again. Now it will spin for a few seconds and stop. I spend musing it.ore time getting it spinning again than using it.
It it dosen't spin properly the filter may need to be cleaned or the jets may be partially blocked. If that's not the problem I'd take it back to the seller. You may have a lemon.
It looks just as clean to me. However, if you try to cover too much area too quickly, it leaves swirling patterns. These cones are best for dirt. If you have other types of stains, you may have to use your wand.
I found a bearing on e bay, but I can't post the link. Do you think it will fit my Ryobi? It is titled " Repair Kit for Pressure Washer Rotary Flat Surface Cleaner Concrete Decks Swivel" by myauto-1
I'm sorry. I really couldn't say. Is there a return policy on ebay? I bought an unloader valve for my pressure washer on Amazon. They listed my model no. but it wouldn't fit. Fortunately they took it back for full credit.
My ryobi seems to be losing pressure from between the bearing and the brass wand holder that spins. It seems to be loose and wobbly. Does that mean that the brass part or the stainless steel bearing is worn out.
Could be. Mine has a little play in the assembly but not a lot, and I'm not having the pressure loss problem. Make sure your tips are clean. If the are partially clogged, it might put extra pressure on the bearing assy.
Very good. I took out the high pressure filter and cleaned it a couple times. This time the little screw came out but not the filter. How do I get it out?
So the screw head came out but the filter and threaded bottom part did not? If so, the remainder of the filter can be removed from the bottom. Here is what I tried today and it worked. The filter housing can be removed from the brass swivel with a wrench. I inserted an awl in the bottom of it and it will slip through the hole in the threaded part of the filter. I applied pressure to have it firmly seat against the filter assembly and backed it out. If you over tightened the filter, you may have to tap the awl with a hammer to make it seat tightly. When you reattach the housing to the swivel be sure to use pipe dope or teflon tape or it will leak. Hope this works for you.
Thanks for the video really helpful. My surface cleaner is having a problem, and I wonder if you can prescribe a solution. Water is coming out of the space between the bearing and the nozzle attachment; this is stopping the mechanism from spinning. Tried taking everything apart and cleaning it but no luck. Haven't tried greasing the bearings yet but don't think that's the problem. Do you have any ideas?
If it is a sleeve bearing like mine, I would suspect that the upper seal on the shaft may be worn out or there may be abnorrnal wear if you've had it a long time. If you grease it the water pressure will just wash the grease out of the bearing.
I'm sorry, I somehow missed you comment when it was first posted. To answer you question, while the brush is still wet after use, I spray it with household cleaner, let it sit a couple of minutes, and hose it off. I use an old toothbrush on problem areas. I really haven't had much of a problem with it getting really dirty though, but I'm not using mine in a commercial situation.
@@deerparkhomeshop2471 thanks for the response. I may have made the mistake of not rinsing the concrete before brushing. I just went straight with the surface cleaner and picked up a lot of animal hair and stringy plant debris around my house.
Hey man! I’m starting a pressure washing business at 13! Would this be a good one to start with or should I get a bigger one? And I’m looking at a 3300psi 2.5gpm ryobi washer. Will that be enough for driveways and sidewalks?
13 years old! My hat's off to you I started working at 12 mowing lawns and was one of the few kids I knew that had a nice bank account. To answer your question, I think the 3300 psi unit has a Honda engine, and is similar to my 3100 psi unit and I really like it. Remember that this is a consumer model and may not hold up to day in and day out use. However even entry level commercial washers cost a lot more, but if you're planning on using it a few hours a week it should be fine. If your business is a big success, you can buy a higher capacity unit and keep the ryobi for a back up.
@@deerparkhomeshop2471 hey! I got it for Christmas! I have an issue already though. the pressure relief valve flew out and wont pop back in. If I can't figure it out ill call Ryobi customer service. Thank you and happy new year!!!
I don't remember a check yalve being on mine. I'll have to check tomorrow in daylight to see what you are referring to. You don't mean the filter cartridge do you?@@SmozzZy
Primero, asumo que su lavadora a presión está funcionando a máxima presión y que ya limpió las puntas. ¿Tienes la marca Ryobi? Las puntas y el brazo giratorio están fijos en los míos. Las pequeñas puntas se pueden ajustar ligeramente, pero si después quedan un poco flojas, eventualmente se caerán. Asegúrese de que la ranura en una de las puntas esté paralela al brazo. Si ambos están de lado, ese puede ser tu problema.
The "gun" is usually the trigger activated spray wand, not the surface washer cone that I profiled in the video. Is this what you're asking about. Mine came with the pressure washer. The supply hose has a threaded female coupler that screws on the male threaded end of the gun. I'm thinking what you have must be a little more complicated. Perhaps trying to go quick connect to threaded, or something like that. If that's the case you can buy adapters to make it fit. Search "adapters for pressure washers" on Amazon and they have several pages of different adapters. Be sure to get back with me and let me know how it turns out.
Usually, the 12" surface cleaners are designed for lower psi press. washers. There is an Amazon link in the my video's description for a Ryobi model that should work for you. You can check that out, and, if nothing else, use it as a starting point for your search. There are a number of these 12" cleaners on the market. Good hunting!
I've never had this problem. So you have tried to back it out with a screwdriver like we did in the video? If it's stuck try some penetrating oil like Liquid Wrench or WD40 and let it soak 10 or 14 minutes and see if it will loosen then. Mike is brass, so there should be no problem with rust.
It should be OK. If you have been using your washer wand on that deck with a 15 deg. or 25 deg. nozzle, it should be about the same. However, I would test in small corner area first, just to be safe.
I put a link in the video description for a 12" cleaner that would be for your press. washer. Not familiar with a Simonizer, but if it has a universal quick connect it should fit.
For the black seals on the bearing itself, I think your best bet may be your local lawnmower repair center, unless you have better luck searching on-line than I did. Most of the o-rings are probably available at your local hardware store. The shipping costs will kill you online.
I have the same surface cleaner and I used it about 3 or 4times last year. The 4th time I noticed it took some time for it to start spinning, after a few minutes I had no problem. I started it up today and I'm getting no spin on nozzle press. It might spin for 1/4th of a second on Initial press but then stops. It looks like the water is coming out fine so I'm not sure. I tried cleaning out the filter but still no luck. Any idea what it could be
Well, first I would disconnect it and reconnect the spray nozzle to the press. washer and make sure you are getting enough water pressure to the cleaner. The sleeve bearing may need lubrication or, since you have already cleaned the filter, the nozzle tips could be clogged up. All it takes is a grain or two of sand, or what not, to clog them up. Try removing the spinner and flush it out with your water hose. When you're doing this notice if the water is spraying freely out of the jets.
Well, I'm not an engineer so I don't have an educated answer for you. I suspect that the spray nozzle ports may have to be a bit smaller for electric models. It might work for you, but may also be an expensive mistake.
I would have to say no. The 15" size is designed for gas press. washers in the 2400psi and over range. It might work, but it makes more sense to purchase one of the 12" models that are designed for an 1800 psi machine and then you will get good results. I put a link in the video description for one, but there are numerous models on the market Hope this helps!
