No video :(

How To Use NE555 For Inverter 12V To 220V 400W

Подписаться 1,7 тыс.

Просмотров 59 тыс.

50% 1

IC NE555 is a very common and popular type of IC, present in many applications such as LEDs, pulse generators, logic clocks... The NE555 IC itself only generates single pulses, in this video I will combine it with an NPN transistor. To make a 12V to 220V inverter in a push pull configuration. This inverter circuit works stably with output pulse voltage to drive mosfet above 5V.
----------------------------------------------------------
Schematic please download at here
drive.google.c...

Опубликовано:

9 сен 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 49

@oilbay54 Год назад

Duty cyle is around 0.49. That means Q1 and Q2 conduct unevenly. This heats up the core. Secondly the transistors don't have any protection diode. Therefore the inductive kickback when it is cut off will destroy it. In the comments you read those complaints about "pap up". Thirdly, never use this inverter for a delicate instrument. Do not check the secondary voltage with an oscilloscope. You'll have a burnt scope.

@VEERsciencePROJECT Год назад

Very good making keep it up brother

@VEERsciencePROJECT Год назад

Ham bhie bana rahe same isi type ka charging k saath

@taikong7952 2 года назад

Thank you, the clip is clear, the diagram is complete

@UpinkProduction 2 года назад

I love it good Keep uploading videos like this

@DIY_Electron 2 года назад

Thank you for watching

@ahmarrana9732 2 года назад

Nice job

@kamalhusein6688 2 года назад

Can run fan or tv plz plz plz quick reply

@NoypiCraft20 2 года назад

Nice work

@danielchatrie6614 2 года назад

I try this circuit only one mosfet fully on the ic can't power the other side my mosfet burn out because of that

@sahulhameed4437 2 года назад

Super👌👌👌👌👌👌👌👌👌

@franciscogomes8446 5 месяцев назад

Repostas

@nux_asr Год назад

if I use another mosfet is there anything that needs to be changed

@qxd666 Год назад

if i want to use 13007 transistor instead of mosfet, what is the circuits?

@carpenterl45hamza 2 года назад

👍👍👍👍👍👍👍

@lakshminarayanasomayajula3295 2 года назад

It is distorted square wave and you would have added another 200W bulb and shown the battery voltage 12V and output voltage 230V with load.

@DIY_Electron 2 года назад

It is not yet complete to run inductive load device. The battery 12V does not have much voltage drop. Only the 220V output suffers a lot of voltage drop, because the transformer has a small secondary winding. I need to upgrade the transformer to ensure capacity. Hope you continue to give your comments, so that I can do better in the next videos.

@lakshminarayanasomayajula3295 2 года назад

The voltage depends on number of turns only. You have to reduce the the SWG of the wire with the same no. of turns which increases the size of the core. The square wave increases the loses in the core. High quality iron core is to be used. The Ah of battery is to be increased to handle higher power like 400W or more. This inverter cannot be used for costly TV’s.

@DIY_Electron 2 года назад

Thanh you

@lakshminarayanasomayajula3295 2 года назад

You would have connected another 200W lamp and shown the battery voltage (12V) and output voltage (230V) It is a distorted square wave output.

@hsb.variedades 2 года назад

Manda esquema pa mim

@SK-is8kl 2 года назад

👍👍👍👍👍

@vittalkoppal Год назад

Can we use D718 with it 🤔

@sayeedbaig7618 2 года назад

Can v use P80nf55 MOSFET by this same components in this same way.

@minhnhat-qz3hy 2 года назад

I want to change the frequency of 36Khz to run a pulse transformer, what components should I change in the circuit to get that frequency, my friend?

@DIY_Electron 2 года назад

Because it is also related to the duty cycle, you have to change the value of R1 with a 100 ohm resistor (R1 connects between pin 7 and pin 4, 8). R2 is replaced by a 20K resistor, you can use R10K in series with a rheostat to adjust the frequency accordingly. Next replace the 100nF capacitor with 1nF. Good luck

@minhnhat-qz3hy 2 года назад

Tôi muốn thay đổi tần số 36Khz để chạy biến áp xung thì thay đổi linh kiện nào trong mạch điện để đc mức tần số đó vậy anh bạn

@ungdungkhoahoc 2 года назад

Bạn chỉ cần thay tụ 104 xuống tụ 222 là được , chào bạn

@kaunghtetzaw341 2 года назад

irf44 use?

@DIY_Electron 2 года назад

Ok you. Usable N channel mosfet

@ChavMusic 2 года назад

Good job!

@mastertech9235 Год назад

Hey foool.... Transformer is main parts bt uu did not share that details

@atikuaticulated5757 2 года назад

what components can i add to the circuit to give power output of 1000w?

@radargenta Год назад

the MOSFETs and Transformer must be compatible with power

@danielchatrie6614 2 года назад

I don't get why the gate voltage is 51volt what happening here

@danieledeboni8934 2 года назад

It's its frequency

@full954 Год назад

Нет даттайма полёвки такого не любят.

@magaiver5640 2 года назад

ta doido da mais trabalho do q mexer com SG 3535

@evgeniylazurenko 2 года назад

Please scheme?!

@DIY_Electron 2 года назад

Diagram in the video description. Thank You

@evgeniylazurenko 2 года назад

@@DIY_Electron Thank you very much!

@k4728X6 2 года назад

Transformer rating/model

@k4728X6 2 года назад

Please mention it

@polatmexmetoglu3175 2 года назад

Xelo

@Dc_tech386 Год назад

No no this design don’t work trust not everything you the c1815 npn transistor won’t work because if the npn can’t spike the current the two mosfet will turn on as ones the right way to do it is use s8550 pnp and remove the 2k resistor to base and ground connect emitter to positive and collect to the mosfets gate each high signal turn off the low side and each off time of high side the negative signal turn on the low side mosfets that’s the the way it’s done