If any one ask about do u have a wrench? Pathetic I have of plenty of tools more than you have trust me was not home and I had time to post this help people out and edit I have other videos with plenty of tools I don’t make money off RU-vid or nothing stop asking that stupid questions if u got something negative don’t comment
At first I didn’t believe the solution was this simple because I have been trying to figure this out for months, but this was actually my problem. Pulled the connector out alittle bit and put some bulb grease in there and everything was working as normal. Thank you so much
You also need to slightly pry out the tab that is on the interior side of the socket. I pulled the bottom tabs only but the problem kept coming back after a few days until I realized there was another connection on the SIDE of the socket. Thank you for this video. It has saved me $$$ in garage repairs.
Thank you so much! I faced this problem yesterday, thought I needed to take the car to a mechanic. Came across your video and I fixed it myself, following the steps closely. Very informative and useful, thanks!
Thanks for the video. My daughter came home today telling me her 2016 Hyundai Elantra turn signal was blinking fast. I was going to go to the store and buy some bulbs but then I found your video. Took off the housing. Gently pry up the connectors with a tiny screwdriver. Put the bulb back in and it works fine.
Thank you for the video! I have a 2013 Hyundai Elantra & your solution was 100% accurate & solved our problem. We took the car numerous times to a mechanic because the same bulb kept acting up, & their solution was replacing the bulb which only worked for a couple of months at best. I am not the handiest guy & desperation drove me to your video which allowed me to permanently fix the problem in less than 10 minutes. Thank you very much!
I just replaced both bulbs and was scratching my head as to why they were still hyper flashing. Two tugs on each spring and bam! Good to go, thanks man!
Thank you for sharing. I replaced my turn signal bulb without removing the entire light housing. It is easy to get to, you just unscrew it and it pops right out. I cleaned it and replaced the bulb, all is working perfectly as it should.
You saved my life. I followed your instruction, and its working like a champ now. I was planning to buy a new bulb for this. You saved me time and money. It took me approximately 15 mins... Thank you very much
Thanks so much!! This solved our problem too. I was stumped cause we replaced the bulbs with new bulbs and had good voltage at the wiring harness,and still couldn’t get it working. I found your video and did what you said and now have working turn signal lights. Needed it fixed for vehicle inspection. Thanks for your help!! I also subscribed 👍
This just worked like magic! I was thinking about how much it would cost me if I took my car to a repair workshop. I did the exact thing as shown on the video and my turn signal started working normal. Thanks for you video!
The front 2 screws are 10mm, and the rear one is 12mm. In order not to hit that little piece, remove the clip. You may not have to remove the headlight if you have an angled small pair of pliers. Great video help!
MAN, THIS 100% WORK, I CHANGED THE LIGHT BULB AND IT WAS STILL HYPERFLASHING, I WAS JUST ABOUT TO SEND THE CAR TO A MECHANIC WHEN I CAME ACROSS THIS VIDEO. I DID EXACTLY WHAT YOU DID AND IT WORKED!......YOU SHOULD CHANGE THE TITLE, PUT SOMETHING LIKE "HYPERFLASHING AND LIGHT IN GOOD CONDITIONS". ANYWAYS, THANKS A LOT MAN!
Just came upon your video. My daughters car is having the same issue on her 2012 Elentra. I had replaced the bulb, then I week later started flashing quickly. It was driven me crazy. I will get back to you once I do it. Luckily it’s on the passenger side. Much easier to reach. By the way if you take fuse box cover off, you can reach turn signal.
Been struggling with this for weeks since I changed my bulb. Just got in from screwing around with it and found your video. It’s dark out and I’m going to try this in the morning. Thank you!!!
Thanks for the video. My sister's 2013 Elantra had the same problem. I told her to take it to a mechanic because he'd have to remove the bumper cover to get the headlight off. Then I watched your video and got it fixed (without having to remove the bumper cover!) Oh, and don't worry about the "no wrench" jokes from your viewers. They (and I) know where to come for answers.
Hey, thanks buddy! I didn't think it was going to work because the contacts shouldn't loosen up that much, and they looked good when I popped out the bulb. I used a tiny screwdriver to bend them up a bit. Now, good to go!
Everett, thanks a lot for the video. It worked like a charm! I was able to remove and replace the bulb holder without removing the headlight assembly as well but removing the headlight assembly wasn't too complicated or labor intensive either. Thanks again and keep up the good work! By the way Everett is a cool name!
Did this in 10 min rn if you have common sense you can do it just gotta pop out those two metal pieces out little more then it will go out the erratic light great videos about from Hawaii🤙🏻
2014 elantra GT ... don't need to remove the assembly - can access the bulb fairly easily just find the correct 'cap' ... cleaned /sprung the contacts and all good. thanks
On mine i switched the left to right left was messing up and right good it work for one day and then it kept blinking rapidly ..but I gonna give it a try to this new truck you’re showing ..might save $hundreds
Wow Yes thank you so much!! It was exactly my problem and it took 3 seconds to fix! Ps: dont need to take out the entire headlight to take out the bulb ;)
Funny, it worked, then it went back to the quick blinking, then I hit the headlight with my hand, and it worked again, and has been working ever since.
My 2013 was at the dealer for a month because of this issue and window washer fluid not coming out. I was told it's the BCM so luckily it was covered under warranty and that still didn't fix the issue. So they said the wires had corrosion on them and cleaned them and then magical it worked well so I thought .Picked the car up yesterday and the turn signal on driver side worked hot home and it's acting crazy and will eventually stop working again ..
Awesome, thanks for this video. It doesn't show the specific problem I was having but I can try to see if this fixes it when I get some tools to take the headlight out. Unfortunately I have a feeling the problem might be a bigger issue however as this morning when I got into my car to leave work the headlight was working normally, but when I went out later in the evening to go get my check from one of my jobs and to doordash the issue came back. Funny enough though halfway through the time I went doordashing the issue resolved itself again.
Yes when u pull those two springs towards you than put the bulb back in that should solve it and u won’t have that issue anymore same thing was happening with me try it good luck thank u
It should solve the problem if it does not u might want buy the whole clip and change it out but for me it has fixed issues just make sure u do it right make sure it hold firmly good luck 👍
Any suggestions/ help i have a 2015 hyuandai sonata replaced signal ights they both work without the headlight being on but when turning them on both signal come on but with not flash
Hi I have Hyundai Elentra 2008 1.6 my car problem blinking light D,2,3 L and epc some time hand break what is problem please tell me I’m waiting for your reply
U know the medal inside of socket that hold the bulb or give power to the bulb those medals pull them towards u so they can hold the bulb firmly it’s a mess with those lights got rid of the car
I have 2012 Hyundai Elantra. The rear turn signal on the left side works but there is no flashing light at the left front outside the car. The left green flash light flashing very fast on the dashboard inside the car. This happens right after replacing Steering Coupler. Is it possible the replacement mess up the left flashing light?
Wow..man ! You are the man,but on witch model you did this? Basicly you don't have to remove the headlight completly:))) And what about if the bulb just burned out ?
hyundai sonata yf 2010. My driver's side turn signal is flashing rapidly. All bulbs are bright. I changed the light bulb but it still blinks fast. Can you help me where the fuse and turn signal relay are located? thank you very much.
I have the same problem but on both sides. Also one of them stays solid when I turn on the parking/headlights, I tried tugging on the springs and it didn't work for me. The light that was stuck on I put on the opposite side and the problem followed. I think it may be the socket itself. I ordered two from the dealer to see what happens since they are not that expensive. Hopefully, this will do it. Did you unhook your battery? and if so did that work?
Hi i dont know if you respond butt i have a hyundai elantra 2013, everytime i turn on the headlight the turn signal is on the dashboard and frozen. Like it would just be on and im not signaling to turn, its not flashing but the light is frozen 🤷🏽♂️
No but weird thing is i switched the bulb from the driver side to the passenger side and havent had an issue yet but i did replace the socket at first when that didnt work i got the factory bulbs thats didnt work so i switched them around and it worked .also there arnt to many how to videos for are cars on line so the 2014 and the 2016 are near exact when fixing issues keep posting fix videos on line cuz i will definitly watch them buddy i currently when i drive fast around corners and hit a bump my rear end will jurk hard almost lost control on the freeway going 65 around a bin wasnt driving irrate just doing the speed limit but the back dont have sway bar links
@@everetthobbies2062 at first i used a light stick and i tested my connection to male sure power was going to it and there was so i found it odd that id get hyper flash with headlights off but with them on it wouldnt work tho i did do as you said with both sockets to make sure i have good connection to the bulb but when that didnt work i switched them around and they work good now so thanks for posting
I cant believe you cant just unscrew and screw the bulb in I've never owned a car you had to take the thing apart to change the bulb. What a ridiculous design
It’s tight to get your hands in there to loosen the bulb, luckily my young son was with me and I pointed out where the bulb was and his smaller hands he was able to get the bulb out for me. The driver side is harder to get to than the passenger side. You might be able to reach it with long needle nose pliers to loosen it 1st.
I had this problem we bent the tabs up a bit on the outside and inside of the socket piece and it worked for the trip to the store and back then to my friends house the next day. On the way to my car i noticed the drivers side front flasher stopped working again (perfect timing being midnight on a holiday weekend with 1000 cops out). I took all the back streets home to avoid any unwanted attention and then half way home it started working again. Still not sure whats causing it but dont have the money to get it in to the shop right this minute anyone have any idea ill check fuses when i get up.
