I Made The World's STRONGEST LEGO L-Motor!! 

Brick experiments has lifted 200 pounds with a single motor. The main issue you ran into was no additional gearing/tackle, and of course just the lego axels having limited strength. It's a good start and I'd love to see your motor power things once you have a better output system

The motor can lift 20 lbs, and I cannot curl a 20lb dumbbell with my left arm. I'd say this machine has *superhuman* strength.

As an engineer I can tell you: with one of these you can't move a car But if you build 2 of these motors they could actually move you in a small rideable thing like a go cart. Lego built a full size driveable Bugatti Chiron, they used 1.500 L-Motors which produces a torque of 50-74 Newtonmetres.

Who’s gonna tell him that no matter how strong a motor is, you can always outperform it using gear ratios, leverage and pulleys?

I'm amazed at your creative

Should I make 3 more motors and build something rideable??!

LEGO Technic team actually did make a car, a Bugatti Chiron once with LEGO and even with a powerful LEGO motor engine, the same principle as here. This is really mind-blowing. #LEGOtechnic

Yes, build three more! In a sense, you've basically combined all the torque from each motor. I think it's safe to bet that it's even stronger than the metal motors you find in RC toys

5:17 "its a bit sturdier its quite a bit larger" got me laughing in the central square

6:10 this sounds like a high powered drone

I wonder if there's a point where the friction caused by extra gears counteracts the torque created by extra motors? Like if there's an upper limit on how much you can get out of Lego motors

I learned a new word today restertified :P

YES! make a CAR using four of those on each wheel! I think it would work!!

As an engineer, I can give a couple of tips: 1. Use gears connected in parallel on the same axis. This will increase the strength several times. 2.Under high load, the axles also bend. You can use the holes in the gear to connect it to the load. 3.Reduce the load on the intermediate gears. Add gears and gearboxes separately for each engine. Exclude all gears connecting the motors together except the central one. 4. Reduce the speed in favor of power - increase the gear ratio with a multi-level gearbox, similar to the one at the end of the video. I'm sorry if I made a mistake in words - I'm an engineer, not a linguist.

A thoughtful commentary on the wonders, but also the dangers, of technological progress. When he said "it's L-motoring time," I cried. The apocalyptic ending was fearsome. Truly one of the films of all time.

I have a feeling that this will be Riley's only creation that serves as an powerful alternative to other motors. SOOOO EXITED!

Brick Experiment Channel does a lot of Lego gear ratios. He's got metal axles that he uses sometimes because they don't bend and twist as easily. You could check those out

I can’t wait for this to start too!

I like that you pixeled the motor in the Intro, but showed it already in the thumbnail

‘’ THE ENGINEER ‘’

Can’t wait for this to start 😁

Request: Build a Martian Tripod out of LEGO.

No matter how strong you make the motor the weak point is the output shaft. There is a limit in the torque it can handle...

Build more MEGA MOTORS and make a Lego car. That would literally be crazy awsome.

You should rebuild this using all metal Lego axels and gears

You can definitely make a viable vehicle motor from these, the issue is the output shaft is so small and flimsy it would just break or twist before it could move anything. If you can find a way to make a thicker sturdier shaft, it will hold up to more torque.

You could literally do the same thing with 1 Lego motor. You would just need a high torque compounded gear ratio, similar to what you have done at 8:03 but the opposite way around. But what you did is not completely useless because just making a very high torque gear ratio would make the last gear spin very slowly, you made the last gear spinning quickly while still having a lot of torque.

Won't be as powerful as the Bugatti, Lego made. It had 200~ motors in it

i love when you look at your camera screen

Please make a life sized rideable Lego car

8:28 assuming each motor is running at 300 rpm, the output is 8100 rpm 300 x 1/5 x 40/24 = 100 (rpm of the “mega” motor) 100 x 3/1 x 3/1 x 3/1 x 3/1 = 8,100 (final speed)

The main problem with this motor is just what it is mostly made of, use iron or heck, even steel and its strength will increase by a lot more

Nice video, I did the math and it looks to be a 1:81 gear reduction and 22,036 rpm (if the motors are running at their full speed of 272 rpm) The super motor has a gearing ratio of 3:1 with 91 rpm.

Smoke and flames coming out of your head was a nice touch!

now you have to make that rideable car

What did that poor globe ever do to you? I thought the globe had already established it's insane dominion.

Tip, you can drastically decrease chances of stripping your gears, just by adding more contact area between any connected set of gears. How can you do this? By using multiple of the same sized gears on the same axle. The more gears you add, the more torque they can handle. Basically just take however many gears you want and pair them up in the same way you would connect 1 gear pair. Im high right now but i have a masters in engineering, i just hope u understand what i mean😂

Besides being really powerful, that motor looks pretty cool as well! Can't wait to see if you make a rideable thing with it.

It is amazing to see that this video make lot of views! Congratulations! I make lego stop motion . You can see it .

My hypothesis: it won’t be fast, but it the torque will be multiplied by the amount of motors

More gears on a single axle! That will help your axle twisting issue as the forces will be more evenly distributed on said axle, since it has more contact points.

Put 2 opposite of eachother, connected to a diff. Your power will double, and make up for whichever assembly has the first failing motor. Then, feed it into the greatest reduction train that you can fit between the two enclosures. Have an output at a 90 degree angle. Build 3 more, and have them all feed into the same reduction gear. That would be a start. I'll buy Lego stocks in the meantime 😆

I wish I had the parts to build that motor because i'm always building things and my motor is not strong enough!

Next we just need eight of these! (I Would actually like to see that)

2:34 looking the motors and the gears rotating is so satisfying

I think if you were to redo it with with those custom metal axles you could really push the motor to it’s limits. You should also maximise torque over speed by making the gear transfer multi-level, where each gear transfers to a bigger gear, then a smaller gear on that same axle transfers to a bigger gear. It’ll allow you to drive way more with the motor

You don't increase power by going down in RPM but increasing torque. Power will be the same, always. Unless you put in more powerful motors.

You should try putting the motors in front of each other so they turn the same axis. Also try to reduce the number of gears to reduce friction power loss.

Parents: LEGO IS KIDS TOYS Him: Hold My Spiky Brick

what a speedy lego motor.

One way to strengthen the axle maybe would've been to attatch lego peice 4185 straight to the cog, then run axles through all the holes and use these along the entire thing, this would give a VERY strong axle that would be highly unlikely to break

A good test of the force it gives is to attach a lever and have it push a scale

Would love to see a tutorial on how to make the finished motor!

Try using an XL lego motor as they are extremely powerful. And try using buwizz as it gives 2x power and 2x speed

I love on the Lego thing for the steps one and two and stuff they’re all the clicks

fantastic build. If you split the load by having two spools, it may help. Or using a pulley? Anyway great to watch, love the power switch idea, very cool 👍🍺🇬🇧

SPEED AND POWER!!!

guy literally building lego says dont do this at home

At this point, you need to go full on with metal gears and axles.

"What is it doing? It's learning!" Great vid ;-) !

yes indeed you definitely built the strongest motor it's not 100 lb but 20 lb is very successful this is a very strong machine!

Me when i am bored be like :

sauber gemacht. ist gut geworden🥰🥰

Imagine you have four motors like this and you have a lego-car you try to move...

Congrats at 500.000 subs!

I think you should replace some of the Lego axels with metal axels so the axels are stronger and harder to bend

4:03 This is basic knowledge...🤦‍♂️

Wow l think you should make another super strong motor with metal Lego axels and 16 motors

This is sick next try making a giant Lego clock

I love your videos❤!

“A motor to surpass lego durability”

I love some well used Swagger Stagger

Eight of these megamotors combined together to make the ultimate ultra motor

If you can get your hands on a dead M-motor, open it up and replace the motor core with a motor purpose-made to modify a flywheel dart blaster, like an Out of Darts Kraken; it should fit. Just need to power it with a separate 12-volt 28-amp or more supply. There are power supplies made for LED projects that output 12 volts at up to 30 amps...

now build 8 of these and combine them to an even bigger motor

if only there was a lego clickbait remover machine! "I made a strong motor pack out of lego"

Now make more and make a working car with it

So now you should combine this motor as a little one of next hight system, it will be cool if you designed it in the same way :3

"As you can see, it sounds very weak." Yeah big brain time 😂

now, make 7 more, and attach ALL of them, into *one* . To make The *ULTIMATE LEGO MOTOR*

Make 3 more and then do the same thing with them as you did with the normal lego motors.

Wouldn't both the engines in the thumbnail both have to be at 100 percent to make it fair???

I dare you to make a lego car from only gears and rods

now we need 8 of these motors combined into one, to make a real elevator for people to ride on

Video Idea what if you made forur of em together and made custom lego tires and then make a massive rc tank or car

You can also try putting different sized gears next to each over, then wrap it in a lego chain/belt. Because this is unable to spin, so if you see this comment, please try it

When you put the 8 small motors together to make the big motor, you need to make 8 big motors and put them together now and make a super motor.

I know it would technically be lego anymore but you could make the axel out of metal instead so it can actually hold the weight

THAT THING GOT SOME TORQUE

build it with metal lego pieces (not sure it there are originals, or only offmarket). It will surely take care of broken axles and gears. Maybe even make more torque :D

Now make the new world's strongest LEGO l-motor with the current world's strongest LEGO l-motor And if you're wondering, yes I am a psychopath 😊

5:48 when you made that you could make a drill at the top and put your hand inside

POV:your an engineer and your addicted to lego:

Brick science: " I think it might be one of maybe thee strongest Lego moter" Motor: Can only lift 20 pounds Brick experiment: ha pathetic

Imagine using this in a Lego technic car

Cool job. You got 8 large motors. Im not sure that 6 buggy motors is weaker. I got 6 buggy motor ripsaw- i think it got even more power in it. With 4 buggy motors i broke world speed record (50km/h). They all connect to the same axle

Imagine if Lego saw the design and decided too make a mini car like a small Tesla out of Lego that kids could build with their parents and use this motor design to make the wheels turn. It would probably cost a few thousand dollars.

Create a LEGO car out of LEGOs by using that LEGO engine you make 😊

Make 8 more of these and make an even more powerful motor to make a R A I L G U N

I love it how he is safe