Merci, pour votre investissement dans cette vidéo opérationnelle et bien filmée !! Toutefois, je reste un novice, il me reste une interrogation, concernant la référence du transistor utilisée ... Si vous aviez la gentillesse de nous la révélée, je tenterai ce montage !! Que DIEU, vous bénisse !!
Buddy, if you assume he may have a hidden battery, wired to the screw, then at 4:46, when he soldered the wire, he have completed the circuit, the motor did not run right away, but once he introduced the 9 volt battery during 5:11 only the motor started spinning. So if you by chance have that doubt, drop it please.
@@seshamxy9135 and you didn't think about a super cap tied to the screws that he charged up with the battery?especially with how long he had to hold the battery on to charge it? or the fact he has the magnet rotating in the same way as the coil? to generate power the magnet has to cross the coil not move with it
@@elk3909 remember if he attached any wire to the screw from below the table or what ever setup, while he turns the whole set up anti clock wise, there should be a wire visible. Ain't visible right? So no extra wires Super capacitor of the size that fits below the wooden board, again not possible, because super capacitor of that size need to be invented here after only. There is no strings attached here. There are even proofs of what you are asking about. But high power machines, unlike this, which is a low power electrical over unity generator. It's simply not accepted because it doesn't fit in a formula. There are calculators which calculate torque used by the motors and generators at the specific rpm. They are available on internet. If you use them properly, you can find this video is not false type.
@@seshamxy9135 i could do this also if i take a dead 3s lithium battery in over discharge protect so one or more of the cells are below 3 volts causing the battery to not put out power. than hide this in the lower side of the board. and then use the 9 volt battery to charge the 3s that is connected to the screws which would bring all 3 cells above the over discharge voltage turning the 3s battery to turn on and then power the system. you will notice in the video that when he connects the light the motor slows down as would be expected if the motor was infact powering the system but in reality it is the lights power draw pulling the 3s batteries voltage down.
Rotating a magnet end-on to a coil won't generate anything, the mag flux is not cutting the winding. And even if it worked, you would never get 100 watts out of that.
Thank you, for your investment in this operational and well filmed video!! However, I am still a novice, I still have one question, concerning the reference of the transistor used ... If you had the kindness of us revealed it, I will try this montage! May GOD bless you!
that is a diode not a transistor and this video is click bait notice how many ads he has in it. the reason its fake is the 'magnet hes using is either juct a iron core from a teroidal transformer and even if it is and actual magnet, any electronic engineer will tell you that the north and south magnetic poles need to alternate at a 90 degree angle across the coil. its more likely that he has a power source connected to the screws under the board
Since 15 years, I have been dealing with angular energy electricity generation systems (R&D). My positive designs about angular continue. In this regard, my own financial means are insufficient, I had meetings with many businessmen, they accepted the financing of the project, but they gave up when it came to signing a protocol, that is, when it came to formalisation. If there is an entrepreneur who will take firm steps with me on this path, who is idealistic, has financial means and wants to make an official protocol, I would like to meet. 98% of the published videos are wrong and do not work. I know the mistake they all make.
Is ply board ke andar buyer laga hua hai niche Mein induction chulha Hai Usi per rakhkar kar ham log ko bevkuf banata hai na jo tu kar raha hai na usse pahle ham Karke Chhod chuke hain
