I Never Knew This TRICK About the OSCILLATING MULTITOOL?!

Подписаться 859 тыс.

Просмотров 815 тыс.

50% 1

Learn To Use Power Tools Safely! (Check Out POWER TOOLS EXPLAINED!)
www.thehonestcarpenter.com/
Check Out Our FREE GUIDE: 25 Best Carpentry Tools Under $25!
www.thehonestcarpenter.com/op...
AFFILIATE TOOL LINKS:
Dewalt Cordless 20v Multitool Kit (Seen In Video!):
amzn.to/46LICVy
Dewalt Corded Multitool Kit:
amzn.to/3FfdGBg
Avid Power Multitool Kit (Great Value!):
amzn.to/3rIFTxn
Milwaukee 18v Cordless Multitool (Tool Only):
amzn.to/3rIFTxn
Vtopmart Multitool Blade Set:
amzn.to/3QgKxfl
Bionsi 35 pc. Multitool Blade Set:
amzn.to/3rQfRYW
(Please Note: These are Amazon affiliate links. When you shop through these links, we receive a small commission at NO EXTRA CHARGE TO YOU!)
I Never Knew This TRICK About the OSCILLATING MULTITOOL?!
Many people rely on multitools to make plunge cuts in various spaces. And most people use multitools with the blade projecting straight out the front of the tool.
However, some people insist that turning the blade 90° on the adapter is the way to go!
In this video, I tested both ways to determine the proper usage of the oscillating multitool.
What I discovered is that straight-line cutting (with the blade projecting straight from the front of the tool) is preferable in many cases. It utilizes the weight of the tool better, balances the tool in in your hands, and makes sight line-ups easier.
HOWEVER, I also discovered that CUTTING ON THE DRAW was much easier than cutting on the push!
I had never known this about the oscillating multitool before. But it's far easier to initiate and control cuts when drawing the blade towards you.
This essentially changed how I'll use multitools forever...which just goes to show you it never hurts to experiment!
Thanks for watching!
The Honest Carpenter

Хобби

Опубликовано:

14 окт 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 869

@cbauer72 7 месяцев назад

Pointing the blade backward is great for tool storage if you don't want to remove the blade. It compacts the tool and keeps the teeth from biting into hands, tool bags, etc.

@nickadamson6053 7 месяцев назад

I do exactly that, for those reasons.

@jeffh4505 7 месяцев назад

But you have to remove the blade to turn it around, so it doesn't really change anything

@cbauer72 7 месяцев назад

@@jeffh4505Can't argue with that. But the next time I want to use my oscillating tool, the blade is already on the tool and not floating around somewhere in my shop.

@canebro1 7 месяцев назад

@@jeffh4505 I inherited mine from my father in law, and the blade is held on by a screw. So I just loosen the screw, flip the blade around, and then tighten back down. Actually easier than removing the blade.

@nickadamson6053 7 месяцев назад

@@jeffh4505 not mine, held in by a center screw and quick release lever.

@andyh9382 7 месяцев назад

The best trick is buying blades online for roughly $1.00 each, instead of Lowes/Home Depot for around $10.00 each

@TheHonestCarpenter 7 месяцев назад

That show I’ve always done it, Andy. I linked a bunch below!

@tashynskyi 7 месяцев назад

Yes, true that, if you hate yourself

@thebobloblawshow8832 7 месяцев назад

I buy them on line and so far they have been good. I guess it depends on the manufacturer.

@flahertypaintingpropertyso4021 7 месяцев назад

These are not Harry's shaving blades

@kickyourfacification 7 месяцев назад

I wish I knew that before I got mine and bought blades from Homedepot 😢.Thanks for the tip.

@duster. 3 месяца назад

With utmost respect. Your comments about the cutting action is explained in the name of the tool. Oscillating Multitool.

@shoelacedonkey 2 месяца назад

You may be overestimating the amount of people who know what 'oscilating' means.

@duster. 2 месяца назад

Good point.

@Dbright1982 Месяц назад

I feel bad for this guy if he's doing construction. No one ever thought it would peck if rotated to the side.

@alanbarrow7447 Месяц назад

No, the definition of "oscillate" is not limited to rotational movement around a pivot. That said, I would have thought that the action of the tool was blindingly obvious from a cursory inspection of its construction.

@Shaun.Stephens Месяц назад

Yeah, I was shaking my head at that whole section. I won't be watching any more of his videos.

@timbrelig4170 7 месяцев назад

I tend to keep my blade at about a 30° angle - just one notch off from straight - switching it from left to right depending on my access to the work. That seems to give me the best visibility and control. It's easier that way to pull the blade into the work at a slight angle, drawing your cut line with just one side of the blade before plunging in and going to town on it.

@marinusdedreu3833 5 месяцев назад

Same here

@t190uk 5 месяцев назад

Yeah I like the 45 degree angle cut position

@iamleidig 2 месяца назад

Dido. Like for cutting nails between deck board and joist you can use the joist as a fence and hit all nails at the correct angle instead of searching for them with plunge cuts.

@1414141x 3 дня назад

The method of using 'pull' against 'push' is very interesting and your explanation wins the day. As previously mentioned by others - that's why Japanese saws are so accurate and efficient as pulling has a lot more control. Thanks for the video.

@Retaile23 7 месяцев назад

The great thing about changing blade angle is for tool clearance and work position. My oscillating saws really shine when cutting drywall. Great video!

@quemeese 7 месяцев назад

I find it very hard to believe anyone would not know the blade moves in a very short arc

@contessa.adella 7 месяцев назад

Same! Why would anyone think otherwise, idk.

@rookie28604 7 месяцев назад

I didn't have any idea, but I don't use mine much.

@handsbasic 2 месяца назад

Seriously lol

@dannylutz194 25 дней назад

Agree. If you have ever mounted a blade, it is obvious.

@unquiche 7 месяцев назад

You’ve learned why Japanese hand saws cut on the pull - much more control and ability to apply more force

@janshannon4553 7 месяцев назад

Thank You, That is not enough for you, you are truly amazing for doing what you do to help and inform us. I am a 60+ yr old female Diy-er, and I have learned sooooo much from you. You explain in simple, yet depth. As far as this one video, I use a multi-tool a lot, and I am so glad you did this video. How truly cool to learn all this. I have truly learned so much from you, and can't Thank you enough. You are truly a God send!!

@TheHonestCarpenter 7 месяцев назад

Thanks so much, Jan! I greatly appreciate that positive feedback. And I’m really glad the videos are so helpful! 😄🙏

@dangrimes5078 Месяц назад

Truly?

@billybrown6330 27 дней назад

A cutting trick that I use on straight cuts is to temporarily attach another piece of wood a long the cut line using Brad nails or double sided tape. The attached piece helps guide the blade straight and square improving the cut. Additionally, changing the speed on the multitool to a lower setting helps improve the quality of the cut, especially when cutting thick pieces of wood.

@abe677 7 месяцев назад

Great video. Technique information is always welcome. I have a tip to share about using oscillating tools. DO NOT use one of these tools inside a closet full of your wife's clothes. Empty the closet first.

@TheHonestCarpenter 7 месяцев назад

Heck of a tip, Mark. 😆 There will be a great deal of dust!

@ShanLiB 7 месяцев назад

Don't forget the shoes and the pole the clothes are hanging on. That cost me quite a few points. 😒 Site prep is so important when doing work in situ.

@handyman_horsens 4 месяца назад

I already did it, because she always leaves trash in my car😂

@tatehogan5685 7 месяцев назад

It's funny how some things you take for granted that everyone knows. Like the motion of the blade, I never would have guessed that anyone would think it moved side to side. You're doing important work with these videos. Anyone unfamiliar with power tools can easily understand your format and teaching style. Kudos to you good sir!

@richpeggyfranks490 7 месяцев назад

Exactly. It obviously rotates back & forth. Not side to side. Thanks for commenting.

@ImBooX2 6 месяцев назад

I could not believe it was not known it pivots (rotates) on a center axis.

@dallinhmic 7 месяцев назад

I have used this exact tool for probably at least a 100 hours. I always keep it straight on and almost never turn it to 90°. Just do what feels best and you will do your best to work that way. This is a great tool for cutting out drywall.

@TheHonestCarpenter 7 месяцев назад

Perfect for drywall, Dallin! I did tons of wood siding repairs with it too.

@jeffdyrland2795 7 месяцев назад

I always use mine to cut drywall anymore. It’s probably one of the most versatile tools I use. Grout removal. Fascia. Siding. Works great to remove interior wood sheeting. Excellent when you need to cut something in a pinch or in weird spaces. That’s the only time I use it on an angle. You can save some money by sharpening or re-filing your blades as well. Fairly quickly. Just use a small triangular file and it works like a charm!

@j3dwin 22 дня назад

I've been using my DeWalt and Milwaukee o-tools for years and I didn't even know the blade went on sideways. Learn something new every day.

@donwilliams3626 7 месяцев назад

I would be interested in seeing this comparison with other style cutters too. I am impressed with the half moon for straight cuts.

@Mark-EFMB-Combat-Medic Месяц назад

Great examples, particularly the pulling vs pushing and multiple points of contact. For most things, I use the half round blade which seems to allow me to not focus on the exact orientation of the blade to the work, less chatter and a straighter cut.

@carlb1409 6 месяцев назад

GREAT advice! When thinking about the "draw" first, it's like a hand saw - in that case, the teeth are positioned to cut more on the draw than the push forward. And when striking an initial groove before, it's always on the pull. Like you were saying you'd now prefer with the multi.

@CraigAWSellars 7 месяцев назад

Great video Ethan, thank you. I normally cut with the blade at 0 degrees for the same reason, but I find other angles like 45 or 90 degrees useful in tight spaces.

@robm6335 7 месяцев назад

2 years of use and I’m finding this out now!. Straight to the shed and tried it and it’s a game changer…. Thx champ

@TheHonestCarpenter 7 месяцев назад

Awesome, Rob! 😁👍

@jerryclark5725 2 дня назад

I have used the 90° option when necessary with excellent results.

@gizmo7877 7 месяцев назад

I have his tool so your input helped me a lot. Your knowledge of tools is immense and spot on. I must admit though, it is pretty heavy to hold for me so prolonged cutting is uncomfortable. Blades don’t last long so there’s the cost too. All in all, it’s a great tool. Thanks for the info.

@Oh6Torch 19 дней назад

I normally buy DeWalt for my power tools. I was a bit broke the week I needed one to cut out some flooring trim on a permanent shelf. I bought a cheap oscillating tool from harbor freight. It was corded with an adjustable speed dial and only $30. I figured I’d only use it once. Was I wrong. It’s a wonderful tool and since it’s adjustable, I’ve even cut dash plastic with no burning or melting plastic.

@Rudy32225 5 месяцев назад

Years of experience condensed into an excellent video! I just bought a hook blade that will facilitate that desirable pull direction cut. Thank you for these helpful tips.

@mothman-jz8ug Месяц назад

I recently used mine in a spot where the only way was straight ahead. In some situations, left or right facing might be best - or the only - way to use it. Due to the length and width of the tool, different blade orientations are needed at time, and no one direction appears "best".

@pirakoXX 7 месяцев назад

Cutting a hole in a wall, fx. for outlets, I turn the blade 90 degrees, as I can rest my hand holding the tool on the wall while cutting, and it makes it easier for me to cut the line (straight or curved) more precisely and holding the tool more stable. At least for me, as the tool is a bit heavy for me to hold stable unsupported for a longer time. And I've gotten used to doing it this way!! And "used to" is important, as the video showed! /Pia

@awt 7 месяцев назад

I trimmed all around the bottom of my bedroom skirting board (baseboard) using a multitool, to prepare to lay wood floor under it (removing it would have caused too much plaster damage). I found that a 45° blade angle worked best, with one hand around the front of the tool, between tool body and skirting. I had really good control of blade depth with my knuckles, giving a really good feel of when it had cut through. I think 45° helps for such long cuts because it "flows" in one cut: if you do it straight on, you make lots of short cuts that probably wobble in their horizontal angle more.

@mattsanchez4893 7 месяцев назад

This is why I think your channel is just great, I always learn something new, and not just new, but helpful and invariably better than the way I was doing something. It also really helps instill confidence, which is very important when doing projects!!

@TheHonestCarpenter 7 месяцев назад

Thank you, Matt!

@nickolasklue1164 Месяц назад

This is an interesting discovery that makes a lot of sense when comparing it to manual saws and I would bet that you will notice similar characteristics to what hand tool woodworkers have. Specifically, comparing Western and Japanese saws. A Japanese saw is much easier to start and keep on a line. The tension from the pull stroke just helps to keep everything stable when cutting. Conversely, this stability makes it VERY hard to correct, if you started your line a bit off. Compare that with a Western backsaw where starting a cut cleanly and keeping a line takes more skill and practice but, correction is much easier. I love both styles and the human inventory that led to their parallel invention.

@loboxx337 Месяц назад

Thank you for all the time and effort, good to know the methods for cutting from this tool.

@markknister6272 Месяц назад

Though I am old the oscillating is new to me. I’d seen it used on TV shows and just had to have one. LOVE LOVE LOVE it. As I didn’t know better, I used it with various angles depending on the cut and my positioning. I did notice right away that pulling gave me a better cut. This would have saved MUCH agrivaton in my younger years.

@billm.8220 7 месяцев назад

Depending on what & where I’m cutting, I’ve used my multi tool in various positions. That’s just one of the reasons it’s called a multi tool. 😉

@TheHonestCarpenter 7 месяцев назад

Fair, Bill…fair 😆

@JT-lq4yd 7 месяцев назад

True, it all depends on what needs to accomplished. When I store mine, I store the general purpose blade on the tool as shown at 4:10 until it's worn out.

@JT-lq4yd 7 месяцев назад

True, it all depends on what needs to accomplished. When I store mine, I store the general purpose blade on the tool as shown at 4:10 until it's worn out.

@d1986ben 7 месяцев назад

Multi tools have come quite a ways, as well as the blades. I’m still running a 12 year old Bosch corded but I can’t seem to kill it. One piece of advise I would share is try out the carbide tipped blades; they do extremely well. Also, when choosing a multi tool understand that the degree of oscillation matters immensely in your productivity.

@dad1432 6 месяцев назад

@@joe52428i have a cheap one too. The vibration and noise are surprisingly aggravating, so I plan to buy a much better one.

@d.e.b.b5788 6 месяцев назад

Decided to stick with corded tools years ago, when I realized that different manufacturers make different better devices, so in order to get the best performance, I would have to have a dozen different batteries. Big benefit, was saving $$$$$, plus not having an entire shelf of chargers and batteries... and of course, never running out of juice in the middle of a project.

@sleepinglioness5754 7 месяцев назад

Fantastic! My favorite tool and I didn't know this. I'm going to have fun this winter trying out this new method!!! Thanks THC...you always give us tremendous information. Just proves we're never too old to learn.

@TheHonestCarpenter 7 месяцев назад

Thanks Lioness!! It’s true 😄

@DemPilafian 7 месяцев назад

The *#1 reason* to use the blade straight on is.... so the cutting area is illuminated by the little LED light at the top of the multitool.

@MrRaptorman1975 6 месяцев назад

45 degrees. Straight on you have to cut at a 90 or slightly more and are torqueing your wrist the entire time.

@DemPilafian 6 месяцев назад

@@MrRaptorman1975 It would be handy to have 3 LED lights: -45°, 0°, and 45° The manufacturing cost of the light feature is almost all in the first LED.. Two more LEDs would likely add just pennies to the cost.

@MrRaptorman1975 6 месяцев назад

@@DemPilafian I'm saying the blade is best at a 45

@DemPilafian 6 месяцев назад

@@MrRaptorman1975 Yes, and I agree. I recently was cutting out some trim in a dark closet and really wished my multitool had an LED at 45° so I could see the blade. _(Note: My original comment was a joke about the placement of the LED.)_

@katylowe3504 6 дней назад

I wear a work headlamp.

@eb3005 7 месяцев назад

I use the round, half circle blades to score a line. Then switch to the regular blade to cut through the material. Way easier than pushing that square blade at an angle

@SevenDaysToNoon Месяц назад

Excellent video! Everything I needed! Thanks. 👍

@woodwisdomnonsenseandcats4203 5 месяцев назад

This is a great cutting lesson all around. I usually only use mine for rough cuts but I’m going to experiment now.

@harpintn Месяц назад

I have one of those multi tools. It is good for soft materials like dry wall, and PVC, but it is too slow to use anywhere but a tight area. You can also sharpen the blade with a triangle file to help reduce the cost of using those over priced blades.

@rotfan77 3 месяца назад

Thanks for pointing out the difference between cutting on the draw or pushing away. I’ve done both and didn’t really notice that there was a difference. But I will try to do more draw technique now when I really want a straight line.

@busman2050 14 дней назад

I use my multitool mostly for cutting thick cardboard boxes at home, with blade turned 90 degrees to the left and cutting those large boxes from top to bottom,

@funnyfarm5555 5 месяцев назад

I bought an oscillating multitool in 2012 when I was refurbishing/remodeling a house built in 1945. I don't remember what angles I used the most because I used the tool more for demolition and prep work. I used many styles of blades depending on the task at hand and accessibility. They work great and saved me a lot of time on the job.

@SL1CK1307 3 месяца назад

Very good analytical explanation. Thank you for sharing

@pasqualeparente9776 Месяц назад

the multi-tool is so versatile it is a must have, if you take an old dull blade and grind down the dull blade so that it resembles a scraper blade now you can remove caulking with the tool. You can also detail sand with the proper sandpaper. Polish. Shorten dragging doors without removing them when in a bind especially if very heavy door and you are alone and don't want to hurt your back. It is just so versatile....

@Bluefox1978 Месяц назад

My answer to the orientation is; It depends on the area I'm working. Most times in narrow places I rotate it 60º to 90º but I've also tried to cut straight in narrow places as well. But a wonderfull machine it is 😍

@gerrymcintosh4477 Месяц назад

Great tip about pulling the multi-tool towards you. 🇨🇦👍 Thank you. 💝

@eltonchan7210 7 месяцев назад

it's the tension. when you pull the blade, the blade is in tension, making it stable. when you are pushing, the strength is pushing outwards, with the material being cut functioning like a pivot that want to throw off the blade. Same principle applies to Japanese handsaw which are pull saw and western saw which are push saw. The former immediately pull the blade in tension, giving much more control especially with the start of the cut

@ronaldcach2779 7 месяцев назад

Great information, never realized cutting with the blade moved to the side. Thanks Friend

@ozzstars_cars Месяц назад

I always thought the blade was left to right, never realized turning it 90⁰ meant the blade actually goes side to side. Thanks for the excellent demo and explanation! -Glen

@coolgamer4607 2 месяца назад

My dad isn’t a carpenter but he does have a lot of experience with tools when I asked him about this he said it’s probably for work in tighter areas where you can’t get the blade straight on

@davidbyourplanb 7 месяцев назад

Great tests! I always thought I was doing it wrong by working most tools towards me LOL! I always feel more control pulling towards me, I think that's why the Japanese pull hand saws are so amazing!

@KoS-24 6 месяцев назад

thin plates of metal lose stability when compressed (pushed)

@connicrow9463 3 месяца назад

"cutting on the pull" method means the blade needs to be pointed backwards 180 degrees ? and then start cutting from the far end, and pulling towards you?

@OllieW501 2 дня назад

You mean it's OSCILLATING ...... This is brand new information! 😉

@jbaccanalia 3 месяца назад

I use this tool 10 times a day, for everything including demolition. What i notice most is keep the blade moving and straight in it's trench, with no pressure. Let the chips clear. Best welding slag tool ever. I just use the corner.

@grahamlewin8716 2 месяца назад

Thanks for another great vid! The oscillating multi tool has been a great addition to the toolbox. You made some very valid points but also what speed with blade combo depending on task at hand. The multi tool has got me out of many difficult situations.

@tombarlow6176 6 месяцев назад

Thanks Mister I a a sinior man and was given a multi tool and you have helped me a lot. I am from South Africa 🎉🎉

@TheHonestCarpenter 6 месяцев назад

You’re welcome, Tom! Happy to hear from South Africa 🇿🇦 😄

@Hunter-yc4xi 2 месяца назад

As a professional handyman, I use mine almost daily. I use the blades in whatever position that best suits the situation. I just wish that for the money, (3 for $40.00) that the blades were more durable. I have a 10 year old blade in my hacksaw that is still perfectly good. But I go thru oscillator blades quite often. But they are one of the best tools ever developed!

@KK-WNY 2 месяца назад

I would not have guessed that anyone really argues about the orientation of the blade. I mount it however it allows the tool to fit in the workspace and do its job, or however it gives me the best control. I would think everyone else does the same.

@andrew81632 7 месяцев назад

I used a multitool to cut through the top layer of fiberglass in a small trailer/rv floor. This allowed me to remove rotten wood under it, replace and re-glass it back. I had to constantly change the position of the blade to fit into tight spaces, inside storage cubbies, into corners, etc. No way I could keep the blade in one position for that job. Since then I change the blade position based on comfort and ease of the cut and don't just stick to a single position.

@hfrt29 20 дней назад

I. 'Ve been saying forever that somebody should have a video out showing how to use tools for Women like me that love tools and don't have anyone to teach me. That sounds like a great Thing you got going on

@S1CKTR1CKY 7 месяцев назад

With the Dewalt oscillating tool, which is the only one I’ve used, I like putting the blade at 45 degrees. Awesome video as always

@TheHonestCarpenter 7 месяцев назад

Thank you, SOS! You’re the second person to say they prefer 45…I’ll have to try it more!

@GailBruce 7 месяцев назад

You offer some of the best analysis I have seen. While it seems effortless, your word choices are very close to engineered for understanding. My compliments.

@joshlampe3458 5 месяцев назад

I will challenge you a bit on this, at least insofar as your conclusions on straight-line vs at a 90. You'll notice there is a rubber overmold that makes a head on the business end, use that to grab onto and you'll notice another trick, it's a completely different animal when you hold it this way. 90's and even odd angles become super stable. Give it a try, and great job on the video. My first watch and you earned a sub, great production quality and you do an amazing job. Well done HC!

@user-no5yk6dh1r 7 месяцев назад

This is extremely helpful, thank you!

@jefffree6990 7 месяцев назад

Never thought about it but i will from now on! especially about pulling it towards you, THANKS!

@joelrggizmo1373 Месяц назад

I have tried it both ways. It just depends on what you're doing and what spot you're working in if it's underneath the sink or underneath the counter or you're doing something out in the open it just depends on how much space you have to work with each way works just a little bit different, and also depends on the material you're working with.

@user-er6zg9jp5c 5 месяцев назад

Thank you for this! Very helpful

@henrikmanoochehri4613 6 месяцев назад

Here are some useful but hard to describe insights I hope I can get across. Curved cutting edges on blades are always better than teeth laid out in a straight line. If you can imagine the oscillating action of the tool, you can understand why. As the cutting edge travels back and forth around the fulcrum, the teeth closer to the end of a straight blade push outward just slightly but enough, depending on the length of the cutting edge, to bounce against the bottom of the cut and vibrate the tool out of your hands. Another insight; the longer the shaft of the blade or the bigger the diameter of a round blade, the farther the cutting teeth will travel, increasing cutting speed and cut depth but stressing the motor more so lighter pressure may be warranted. Curved blades also will clear out sawdust better. Straight edge blades push the cutting dust towards the center of the blade, if you can imagine the same phenomenon I described during the first insight.

@ahill209 6 месяцев назад

Very useful observations. I watched the Fein Multimaster RU-vid video and they almost always were running the tool with both hands on the tool, including several pull cuts. As far as the rotational aspect of the cutting goes, there's a reason it's called an oscillating tool.

@jesstapia562 7 месяцев назад

Learned something new…as always thank you.

@warthog1779 7 месяцев назад

Funny - Not only did I learn to pull the MT toward me but also to flip the thing over! That looks much easier to me than using it blade side down.

@ashokmoghe8035 7 месяцев назад

Ethan you always have some interesting videos. Thanks for sharing this.

@jeffb4270 7 месяцев назад

As a 30+ year experience electrician who does mostly renovation electrical work the oscillating multitool is excellent. You can cut what a reciprocating saw or jigsaw can not do. Thank you for the tips on using it I am open to any ideas.

@kw6713a 6 месяцев назад

Have you seen or used the gang box blades? They are basically a rectangle blade that you can use to plunge a single gang hole in one go. They have them at harbor freight and probably some other places. Curious if you've found them effective. For me they'd seem difficult to control outside of half inch drywall. Also a tip I like is to use grout removal blades on horsehair plaster, then switch to wood blades for the lathe. The plaster tears the wood blades up pretty quick, but the grout blades are much more durable.

@panda-threemonkeysracing2116 7 месяцев назад

I have the Hercules corded oscillating tool from Harbor Freight. I seem to lean towards setting the blade at a 92 plunge cut and 45 to cut lines. By anchoring my backhand to the wall to steady the tool and my left hand for fine adjustment, seem to be able to get very straight lines. Love your videos sir

@lantsoghtlaurent 7 месяцев назад

The 90degrees angle cut allows for supporting the tool with your arm more easily by resting your wrist or elbow on the support to cut, especially for the first cut attempt.

@lantsoghtlaurent 7 месяцев назад

I do the straight cut or 30degrees for better alignment though.

@kathe6703 4 месяца назад

I work with dry walls and when I first bought one about 13 years ago, I realised what a useful tool it is. Its a life saver

@garywilliams1759 7 месяцев назад

Another very informative video - thank you. I like the multi tool but I’m still learning how best to use it so this was really helpful for me 😊

@TheHonestCarpenter 7 месяцев назад

Thank you, Gary! I’m really glad it helps 🙂

@johnbayliss1098 7 месяцев назад

Thank you my brother I'm an electrician and I love that tool you definitely taught me something nice keep it coming

@TheHonestCarpenter 7 месяцев назад

Thank you, John! I’m always happy to hear from other trades 🙂

@edpowell5754 5 месяцев назад

Thanks Pal for the information.

@VAFSH4LIF 7 месяцев назад

For me the DeWalt multi tool is hard to change the blades. Being a carpenter of 40 years my hands/grip are about wore out. Great News! Rigid has came up with a clever way to lock the blades in without having to depress a lever with a spring. It has sold me. Great video

@mvblitzyo 7 месяцев назад

Super awesome explanation Thanks for so many exceptional videos

@bdrums Месяц назад

My favorite is the 1/2-3/4 round blade. It's easier to stay in a straight line, (like a circular saw vs a jig saw), and you can rotate without having to adjust the blade on the tool body. Another note, the oscillating tool was created to remove casts, so even if you do face the blade toward your fingers, you're not in the danger most other tools would put you in since these aren't good at cutting soft tissue. ...That said, don't come looking for me if you grab the blade really firmly and the bone becomes your base. But I've grabbed the running (semi-dull) blade many times with zero cuts!

@ryantaron9133 2 месяца назад

Thank goodness the blades are able to rotate. When the blades are spent I use my angle grinder (w a cutting disc) and cut new grooves. This is rough cut only but it’s a huge value and adds so much more life to the blades. Regardless of what price you’re getting them for. Also using double sided tape to hold sandpaper on old blades make a brilliant use of the tool for sneaking into random spots. Top and bottom of the surface depending on the challenge you’re facing. Cheers

@amsohn1 7 месяцев назад

Thanks Ethan, this is great... ive juat started using mine sideways... its been great! Blessings ❤

@TheHonestCarpenter 7 месяцев назад

Awesome, Grams! Try “drawing” the cut towards you-it works great! 😄

@amsohn1 7 месяцев назад

@@TheHonestCarpenter after watching your video, that's exactly what I'm gonna do... thanks again!

@ConcernedCitizenPPCA 2 месяца назад

Where this tool really shines is with a sanding attachment when you are getting drywall patches for all those small holes people make hanging puctures ready for painting.

@howardmakely2169 3 месяца назад

Very informative. Thanks

@bobeaseshop9389 7 месяцев назад

This is such a fantastic tool. I have had mine for almost 2 years and I named it Rex The Wonder Tool. I used it to install a built in electric clock in my bathroom the other day and tried different ways of cuttings a wood backing plate as I was at some odd angles on the shelf I was fitting the clock into. The draw method is very good and useful. Ya kinda gotta let the tool talk to you and just try different things in different spots. Great video as you show the good and bad at various attack angles and that's the key. Don't lock in you process with this tool and go outside the box of pre-thinking on how this tool works. I put on faux foam (GenStone) stone siding on my farmhouse and got this tool mostly to cut slits in the foam upper screw mounting strips so the foam could flex with heat and cold. It did this task with such ease and speed. Drywall cuts are amazing. It can apply to so many things but almost each one needs a different application of use. Thanks for another great video on common uses for common tools. Bobby

@psalm23sheepdog 7 месяцев назад

I angle the blade according to what needs to be cut and the allowable space for the tool. Isn’t that the beauty of this tool?

@tuckersabath2099 7 месяцев назад

Osilating versus reciprocating, these descriptions are self evident for alot of English speaking people. How you hold it though is up to the craftmyn. Unfortunately some folks are raised to think learning is for jerks, so that they adapt to the world around them with a shallow base of understanding. Hold the tool this way, shun the literate that way. Thanks again for sticking to the fundamentals.

@donmunro7568 Месяц назад

I started using one of these saws 15 years ago and I'm pretty good with it now. I use the milwaukee 18 fuel and the basic one also. I'm able to remove center of a hardwood board clean enough that my cut mimics a factory beveled edge.

@brucebrantley6972 2 месяца назад

Working carpenter, forty years, tons of remodel, veteran oscillating tool user. There are times when head-on is appropriate and times when 45 degrees is appropriate and times when sideways is the way to go. Then there is individual preference.

@twobeards6714 7 месяцев назад

I trashed three Fein saws in five years. Bought a DeWalt cordless three years ago and its still going strong

@uinlxa76 7 месяцев назад

You remain beyond max LEGIT. Such a exceptional teacher you are

@TheHonestCarpenter 7 месяцев назад

Thank you, Nick! 😄

@robertkerby2581 7 месяцев назад

Wow, I am amazed! Well done!

@parkerquigleypuff 6 месяцев назад

As a multitool enthusiast, this is the best tool and will pay for itself on the first project. This tool is one of a kind. The best use for the blade rotation in my experience is depending on the location of your cut, you have the ability to change to any angle and make your job easier. And at the end of the day that’s exactly what this tool does.

@danweaver1517 7 месяцев назад

I have this tool, and am waiting for a reason to use it. I am a DIY hobbiest and everything other than the drywall you cut, I would use a different tool for. I do not do carpenter work, but build guitars and stringed instruments. But I build a lot of jigs, cut, plain, drumsand, drill, finish etc. I got the tool on a sale for a great price and could not pass it up, and hopefully one day I will find a good use for it :) Thanks for the video!

@TheHonestCarpenter 7 месяцев назад

It’s best for remodeling work, Dan! The ability to plunge cut in place is utterly priceless. It could literally shave days off of my bigger carpentry remodels 🙂

@danweaver1517 7 месяцев назад

@@TheHonestCarpenter Thanks, that makes sense. I was thinking it might work for me to add a couple of outlets in my garage shop easier then using the sheetrock saw. Thanks again for showing it in action!

@thecrippledstud 7 месяцев назад

“Should you make the turn to 90 degrees?” 😂😂😂. My dad humor loves this.

@TheHonestCarpenter 7 месяцев назад

Puns everywhere, John 😆

@cgodlove 5 месяцев назад

Really helpful tips! Thanks!!

@wk7060 Месяц назад

Great video, like the idea of Pull cutting.

@drwhoeric 4 месяца назад

I too accidentally learned that cutting on the draw produces a straighter and cleaner cut. I also never put the blade in more than a 45 degree angle as the tool is much harder to control.