I've been setting up my bows wrong…. 

This is how you earn respect with your fan base. Good man.

Glad PJ and Lancaster team sent you our Wide Limb Versa Cradle Bow Vise - it's a game changer. Enjoy @ChrisBeeReal ! 🏹🙌

I’ve been running my hip into one of these in my shop for about a year now, it works awesome. I mounted mine hanging off the bench so you can tilt it down so the string is horizontal and parallel to the front of the bench (with a stabilizer on)

Duuuuuuuuude, I've had my standard-width VersaCradle for 10 years now!! I love mine, which is why I bought a second one with the wide limbs. It self-tightens just enough to hold the bow in place, but still allow you to make minute adjustments to level the bow.

I fix the rest cable on the rest and pass the other end through the cable and then again pass 2 cm higher in the opposite direction. The advantage of this is the ability to quickly adjust the length of the rope without a tool, which is very convenient when setting up the bow.

Man, I want one of those new OMP vices! So much more robust than what I have. Big 💵 though for a vice. Definitely worth the money. Money is just a little harder to come by in 2023. FJB!! Thanks for the Video @Chris Bee

That's the best bow vise I've ever used! It would be one of the last pieces of equipment I would ever part with for bow tuning. Great choice for sure!

Thanks for sharing. That OMP vice is top notch.

After watching your video I went out and bought one of those bow vices can’t wait to get it!

I have that bow vise with there 3rd axis sight tool and it’s gets you close to prefect

The OMP Micro Tune was the first thing I ever got for my bow shop.

Excited to see when you build out the new bow 😊

the bow vice is what i have at work they are awesome !

You can bolt the bow vise under the table so the bow is lower and it's away from table so you can leave the stabilizers on when working on it like the way you did.....that's how I have mine set up

Nidio some of her Lancaster archery’s modular archery blocks. Where are you can go all the way to the floor to the ceiling

Nice unboxing. I love my OMP bow vise!

When you are marking the knock point on the string, are you marking the center of the arrow? I see it as you are marking the side of the square against the rest and transferring that edge to the string. Then you center the knock/arrow on that line. Does that not make the knock point lower? Or should it be lower anyways?

Just bought the new Last Chance Revolution Vise kit. It's the best vise I've ever worked with.

Don’t worry bud. I shot our chest freezer IN OUR HOME. Was messing with my daughters release(just playing with it for no reason). Hit right over my target, through my winter coat right into the freezer. 😅

Great video chris. I lol when you missed the target. That arrow will be in the wall for a while.

I have the micro Adjustmen its the best

This guy has helped me learn a lot about bows would like to meet him one day!!!

I love my OMP Bow vise!

Correct me if I’m wrong but I feel like 340 spine on a 28” draw length with 75lb mods would be too light a spine unless shooting a lighter point weight?

Omp is great ive had mine several yrs now but i find myself using the new last chance vise more just because i can swap out from bow to ar in a second but either one is top notch

You should get a Hamskea AroJac arrow puller.

I have the OMP bow clamp . Mine must be the old issue . The clamping system is a pain . It keeps coming unthreaded and somewhat difficult to reattach . Glad I have it but it can be a pain

Dialed in my hha tetra lt today 30 minus 30 is zero got new strings so new sight tape great video as always

Between you and Josh Jones at Podium Archery, I've gotten the courage to get some of these invaluable tools to start working on my own bow instead of driving an hour to my local shop. Keep up the good work, and thank you for breaking a lot of this down for the rest of us!

I have the micro adjust, and I should’ve returned it. Absolutely not worth it. I worked at a shop that just had the regular one and it’s way more stable.

Yes arrows will definitely go through corrugated metal I did that as well I have a nice bullet hole in the sheet 🥳

Should have gotten the Backer Archery products vise… Kyle Douglas even uses it… last chance stole the idea for their new vise from them… it holds the bow by the grip for more security

How many feet of workbench do you have total between the 2 benches and your press? Im trying to build up my own shop and want a long enough table to fit everything comfortably.

The bow square was setup to just contact the rest. Then u marked the string where it lines up but shouldn’t that line represent the button of the arrow shaft? I anticipated u putting the bottom of the nock in line with the silver marker line. Instead u put the mark in the center of the nock. Isn’t the arrow technically pointing upward slightly then?

Love the vids keep up the great work chris ❤

I was thinking....dude is good if he can always hit that target behind the paper. I would have put it in the wall by now! It's not a bow shop if it doesn't have a few scars!

Maybe I missed it but how were u setting up ur bows wrong?

need to film the caribu hunt

Get in line pal, been setting mine wrong for years 😂

Great video Brother I absolutely love my Phase 4 copper with be Amazed with it.

I was just thinking if you ever miss the target while paper tuning and then it happend lol

Cooper shooting 75?! I remember him shooting 45….and a half!

Can we start a go fund me to get Chris a real drill😂

Hello from Maine

Yeah I could probably tell that there was something up because the way you shoot

Your setting your arrow wrong with your sharpie mark ,the way your doing it it will be nock low .because that mark you used on the bow square is the the bottom line of the arrow,and the nocks usually have a tapper to them ,and you centered your nock with your sharpie mark,which will be nock low . You can correct it buy lowering the rest ,but that will take you out of center of burger hole.

Love the videos Chris

😅😅 good stuff, I can't get mine to bullet hole to save my life. 🤣 looks like I'm lobbing a football w a high tail tear 500 grain 300 spine arrows at 65 lbs 30 inch draw

Is it just me or is it every Mathews videos build I see, people are having to swap the top hats?

BAP, Best. Vice. Period. Butch Baker jas it figured out. OMP, meh, better then nothing I reckon.

Compare bohning x vanes vs heat

Fancy fancy bow dillio 😂

Dude...I do tune my bow on the kitchen table lol

I’m in need of a vise and was looking at the OMP vises. How about you sell me your old one 😂

Just got one of your Beereal grips for my Mathew’s, it honestly helped improved my group sizes by a good amount

Watching the video looks like normal setting up bow.

Well Chris……sure wish you could show me HOW to build a bow someday but……..a little slower. 🙂🙂

amazing video, greetings from chile👏

You actually don’t want to put mole skin on the rest until after you mount it because when you’re mounting everything on there the bow is shaking and nothing I’m saying is true at all I just wanted to see how many people would argue with me because they didn’t read the entire comment. PS: why does Cooper always have an attitude with you? No “thank you” or anything. Come on buddy!

340 axis out of a 75# 28” bow? Crazy

Buffalo Bee

LCA Revolution blows the OMP out of the water.

I need someone to build me a new bow. 😂😂

Not gonna lie, kinda jealous that Mathew’s bows can’t be sent to just anyone’s home.

Wow 🐝 no wonder 🤦🏽‍♂️

Can I have the last chance one of you don’t want it anymore haha.

Can I have your old vice 😅

I've been trying to tell you, but you won't listen

glad i never followed you.

you should start giving away all that cool stuff they send you r

@ChrisBeeReal Dude, I've been building arrows and working on our bows with you this whole time. Love your videos, keep them coming.. I'm shooting better than I ever have. Must be doing something right... Go team Matthews!!

Auto tighten is not just a cool feature, it is a SAFETY feature, and very important at that because imagine if you forgot to tighten the bow and let go of the handle, your bow might just hit the table or something and you might end up needing a new cam!

Chris for your apparent struggles😂, as someone born and raised in Lancaster it’s not (Lane-Castor). It’s pronounced Lanc-aster, but not a hard A say it like it’s all one syllable. Keep up the great videos. Cheers

Is it just me or is it every Mathews videos build I see, people are having to swap the top hats?

Go ahead and pop out that metal clip from the black handle. Ups the performance 10x.

Chris man I can’t tell ya how much I enjoy your content, your ability to get information to the average hunter or consumer in a humble and honest way is truly a pleasure to view. You help so many and your appreciation for animals and archery is why I continue to view your content because you can tell money comes second to your true love for hunting and archery. I’m now becoming a DIY myself and a Mathew’s shooter because I believe in the products and you’ve help so many get excited about archery myself included I’ve grown so much from watching your stuff please continue to be you and don’t deviate! P.S I’d love the opportunity to have you come out to New Hampshire and hunt my estate feel free to reach out!!

First

IVE BEEN WAITING ON QNOTHER VIDEO FROM YOU,I’m getting into bow season this year

Whats best flying long range fleching to use with fase4 .. my local shop uses 3 degree blazers is there anything els better

Please build me a bow.

i remember when cooper was tiny. jesus time flies.

Wake up boys Chris bee posted 🔥

You title this as you have been doing something technically wrong..