No video :(

Importing Arduino Sketches Into Atmel Studio 7

Подписаться 23 тыс.

Просмотров 100 тыс.

50% 1

Hands-on: goo.gl/8QTkDg
Atmel’s resident Wizard of Make Bob Martin shows how simple it is to import your Arduino sketches into the new Atmel Studio 7. Your sketch, including any libraries it references, will be imported into Studio 7 as a C++ project. Once imported, you can leverage the full capabilities of Studio 7 to fine-tune and debug your design. Atmel Studio 7 fully supports the powerful embedded debugger on the Arduino Zero board. For other Arduino boards, shield-adapters that expose debug connectors are available, or switch to one of the many available Xplained-Mini/PRO boards to fully leverage the Atmel HW eco-system. Regardless of what you choose, you will surely make something amazing.

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 62

@petergross3382 8 лет назад

REALLY REALLY important tip, which is missing from the video. You have to break the RESET-EN solder bridge in order for the Arduino to communicate with Studio 7. Otherwise you will just get error messages.

@akamba12 8 лет назад

+Peter Gross What dies this mean, or how/where ?

@audiodiwhy2195 3 года назад

@@akamba12 Hey akamba if you look at an UNO (real one, and most clones) you will see a little round dot called "RESET" on the UNO. If you put a continuity tester on either side of the dot it will beep. That's because there is continuity between the reset pin on the 328P and the rest of the circuit. Studio 7 w ICE doesn't like that, it has different timing requirements than the pure Arduino platform. So, For Studio7 to work, (specifically, DebugWIRE) without errors you need to cut this trace. AND! once you do, you won't be able to program your from the Arduino IDE any longer, rather, only from Studio 7. Fear not you have't ruined your UNO. Nono. To go back to Arduino IDE, solder back up that trace and then flash the 328P with the arduino bootloader from Studio7. It's pretty easy once you know the trick. Details here. audiodiwhy.blogspot.com/2021/02/fun-with-atmel-studio-and-burning.html. See the bottom of the post.

@oswaldjh 8 лет назад

OK, I just received my Atmel-ICE full meal deal with the ICE unit, Adapter board and three cables ( USB, IDC and the Squid ). Forty seconds into the video I see an Arduino Uno with a right angle ISP connector that I've never seen on an Arduino. This is connected to an adapter board that goes to a plain flat cable leading to the ICE unit. If things have change this much in less that two years, a followup video would be more than a nicety, it's a necessity.

@studleylee 7 лет назад

Hi Bob, This is great. Please add a sticky or note mentioning the reset jumper cut needed on the UNO. I thought I had bricked 2 UNO units after a bit of frustration.

@keen2461 8 лет назад

This should have been done years ago! I don't understand why it took so long to Atmel to come up with this general public need.

@rsyoung01 8 лет назад

I'm thinking you modified this board by breaking the RESET-EN solder bridge for this video?

@aura100500 8 лет назад

No librares import when sketch does.

@linkpad6270 3 года назад

Is there anyway around this? Does AVR include equivalent libraries? Otherwise I guess you would have to rewrite the code...

@user-nl8wq6uf5j 9 месяцев назад

Hi sir! But I can't to replicate this because Microchip Studio doesn't work properly. After the clicking 'OK' button in the window 'New project' (assumed that 'Create project from Arduino sketch' is selected) this IDE (Microchip Studio) gives message: ''Length cannot be less then zero. Parameter name: length'. And after I try to enter the name into field 'Sketch file' and press 'OK' the application is 'hanged'/ After a few seconds the application is closed and restarted from the beginning. This fault is permanent, that is why I cannot create any project from Arduino sketch. What is Your version of M. Studio? I'll thy to replace my BAD version with Your GOOD one)

@btomas225 Год назад

This thread, as with most from vendors and manufacturers, isn't monitored and they rarely, if ever, respond to answer questions....This thread is 7 years old!

@tube5903 7 лет назад

I have never been able to import a sketch for the arduino due sucessfully. I always get a build error missing chip.h

@ericj2377 5 лет назад

I was hoping there was a good way to go from Arduino sketch originally programmed for an Arduino (Uno in my case), import the file in Atmel Studio and then upload to an Atmel chip that you can select (no Arduino!). Is that possible?

@edwardboston8600 8 лет назад

Trying to import an Arduino Sketch for an Arduino Zero and it hangs with it. I was able to successfully do an import of the blink for an Uno, but when I changed it to Arduino Zero, it hand while creating the ArduinoCore

@Polynuttery 7 лет назад

But did blinky work?

@SukramNotna 11 месяцев назад

Can I also use external libraries with the #include statement? Microchip studio is claiming about it...

@dmrsibs27 4 года назад

I have a problem I was using the Uno template to create projects following Warrick A Smith C Programming with Arduino using AVR dragon with ISP but when I updated the Atmel Studio 7 the templates for Uno and mega were wiped out how do I access these again?There is only this Arduino sketch option now

@mohammedkoyakp6995 Год назад

Hi sir , I have followed the same procdure as you decribed here in microchip studio7 but I am getting Error that deosnt exsist or dont have permission to acces while adding IDE path and skech file . Kindly have a look onthe issue and have a solution thanks

@post2pa 8 лет назад

Hi Bob et al, I am trying to program the Arduino MKR1000 using Atmel Studio 7 directly, not by importing an Arduino project, do you know if this is possible? On attaching the Atmel ICE JTAG I can read the chip set info and fuses etc... but I am unable to download a program, do you know if the RESET-EN solder bridge the issue? Thanks, Paul.

@mirkojelinek6282 8 лет назад

Why there is such a problem to add AVR DRAGON to ARDUINO or Studio 6.2 or Studio 7. I have latest downloads but I'm puzzled how to get it going. I would appreciate any help. Thanks

@driversteve9345 5 лет назад

Why does the order of functions placed in the code matter in ATmel Studio 7 when it doesn't matter in Arduino IDE? Are they not using the same compiler? Is there any way around this? If not, I will regrettably stick with Arduino IDE as most modern programming languages do not have this issue!

@MrPaulw517 4 года назад

Hello Bob, how many Float decimal places does Atmel Studio 7? I have an existing Arduino Sketch that utilizes GPS coordinates to calculate “distance between” values. However Arduino only supports Float 6 decimal places. I am interested in obtaining greater precision and I understand that C++ supports greater number of decimal places than Arduino. Also, does Atmel Studio 7 support ESP32 modules? I am looking at the dual core capabilities to increase processing of GPS coordinates along with Tx & Rx of that data to calculate the distance between two LoRa Radios.

@federicopinto5053 4 года назад

What a nice man

@wryammm3346 7 лет назад

I am working on an ArduinoMega. In Atmel studio 7 When I select the Atmel-ICE debugger/programmer in the tool's tab I can never obtain the debugWIRE interface? it is always SPI and JTAG. I even cut the RESET-EN strip. Can someone help?

@steennilsson5066 8 лет назад

Hi Peter and all,,, Wich function have this solder bridge for reset signal..?Wich error messages will you get..? i cant find any solderbridge on my Leonardo,,,any help will be appaciate. Thanks

@FloTelip 7 лет назад

When I click "New project" I don't have "Create project from Arduino sketch" ! Please help !!!

@shyshopper 5 лет назад

How do I use this method to debug the Arduino Due. When I did it using the Due, it won't compile.

@user-so2xd7pw9l 6 лет назад

Hi Bob, I did a original PCB for a application I used a arduino nano V3.3 in the past. For saving space on the PCB I used ATMEGA328P 28-pin MLF and wanted to reuse my original program. But the pin assigment seams to be different than the 32-pin MLF used in the Arduino nano. I do not know how to access them correctly in the Arduino IDE except direct pin manipulation, but this will be hard work. If I import the sketch to Atmel-Studio can I access the pins directly by there port names like "PB4" ? Where can i check the syntax? would be great help!

@chrisy.703 5 лет назад

In the tool setting, there 're only two interface options: JTAG and ISP. Where is debug wire?

@audiodiwhy2195 3 года назад

Hi Kuo: to get debugwire going you need an ICE same as this vid (other programmers probably work, but I only own an ICE). to get the Debugwire option to work you have to make sure the UNO reset trace is cut (not sure about other Arduinos, you'd have to study the schematic). UNOs have different timing requirements, so you have to cut that trace. OK, once you do that, and build works, click on the solid green arrow that points right. Pick ICE and Debugwire. Next you'll get a warning saying your DWEN fuses aren't set. Carefully Follow the instrucitons on screen, there will be a power cycle needed. Once you do that for me anyway it all worked.

@bobbypatel2824 8 лет назад

Is there any way to go other way around. Atmel code to arduino sketch ?????

@shivaal2640 6 лет назад

Im getting consistently "System drive not specified Errr" when i wanted to open a arduino sketch

@robinsonmira2922 5 лет назад

I have the same problem. Did you fix it?

@user-eg8me4hx5x 7 лет назад

I have watched several videos about Atmel studio, but I have one question here. Is an imported arduino sketch going to be compiled and work the same as a sketch created directly in atmel studio or can it not be optimised that efficiently? I am looking for a way to achieve a faster duty cycle for the same programme and thus I consider using atmel studio. But now, with the ability to Import arduino sketches, if the compiled programme is the same with the one that was created from an already atmel studio sketch , I can just create my sketch in arduino ide and then upload it using atmel studio. Can someone help me here? If my point is not clear but still someone believes they can help me please ask me to rephrase. Thank you.

@standasalvet5743 8 лет назад

When I set DWEN and unset SPIEN fuse of ATMEGA328P from my Arduino UNO board in my HVPP programmer, ARDUINO UNO stopped working. You must be a real wizard!

@steveliu1028 8 лет назад

I have the same problem,have you solved this ?

@standasalvet5743 8 лет назад

No, i haven't, unfortunately, i tray to say that guy from the video is a lier

@steveliu1028 8 лет назад

Hi!Standa Salvet,I solve this problem finally,the key is on the Arduino Uno board,there is two pads called RESET EN(Some version don't have),I use a screw knife to cut the PCB between the two pads at RESET EN,so it open the debugWire function physically，then,magic happened.

@glaucomvp 5 лет назад

'Failed to import Arduino Sketch:'NoneType' object has no attribute 'name'.

@Rafilskis111 5 лет назад

didn't work to import.

@DavidLeeMenefee 7 лет назад

Atmel studio 7 keeps crashing every time I try to bring in an arduino sketch. Please see my youtube video for further detail. Can you tell me why this is happening? Thanks, elecctronicwizard

@vladimirlaiu7893 7 лет назад

Hi guys, can anybody tell me if is possible to use Dragon instead Atmel-ICE ?

@SrinivasaVaradhan94 8 лет назад

Hi sir, this is a great tip !.. It would be nice if you can share a tutorial on writing a customized bootloader through UART1 via a bluetooth module HC 05. Thanks Srinivasa Varadhan.

@puneetmudgal2464 4 года назад

atmel studio crashes when i select the arduino sketch...please help

@sumitchaulya2829 4 года назад

Same problem ...

@kasperverweij9424 4 года назад

It crashes when i do this:(

@santokworkshop 8 лет назад

How to upload the program using native boot-loader of arduino?

@jimpayne782 8 лет назад

+san tok - Not sure if this is what you are looking for, but it may prove helpful: Regarding Atmel Studio 7 and using the serial programmer native to Arduino 1.6.5, there is a great tutorial from Jaycon Systems (for Atmel Studio 6.2) located here: www.jayconsystems.com/tutorials/cat/arduino/post/atmerpt1/ The relevant part begins with "Go to Tools -> External Tools..." Below are the settings I used for the serial programmer for an Arduino UNO: Title: Serial Program Command: D:\Program Files (x86)\Arduino\hardware\tools\avr\bin\avrdude.exe Arguments: -C "D:\Program Files (x86)\Arduino\hardware\tools\avr\etc\avrdude.conf" -patmega328p -carduino -P COM3 -b115200 -Uflash:w:"$(ProjectDir)Debug\$(TargetName).hex":i Initial Directory: leave empty Use Output Window - checked Notable changes from the tutorial include correcting a typo in the speed settings (deleting an unwanted period, this is covered in the tutorial comments), and using 'ProjectDir' instead of 'ItemFileName'.

@tonyhodgson6744 8 лет назад

I was excited when i watched this video for the first time, debugging arduino sketches.... wow... i tried importing my sketch using the same method. when i compiled it, it couldnt find the libraries im using. these are in the default location. isnt AS7 suppose to "Import" ALL libraries my sketch is using??? also i get a "recipe for target" error...

@87steveom 8 лет назад

+Tony Hodgson I'm in the same boat. I wanted to import a sketch for my LCD screen so I could add my Atmel Studio code to it, but it cant compile. If people aren't using complex Arduino libraries it's easy enough to just write the code in Atmel Studio. They need to fix this.

@rishi-m 7 лет назад

Hello there! Did you find a solution to this/ did they fix it? I'm planning to import an Arduino library for an IMU module, but thinking of doing the rest of the program logic in C. Is this recommended or should I stick to the Arduino code?

@itzelyazmingarciacordoba7126 5 лет назад

¿Podrías arreglarlo? Tengo un pequeño código y solo tengo una biblioteca agregada pero no compila. Apreciaría muchísimo su ayuda. Saludos

@shivashankar28 5 лет назад

i hate arduinos, switch over to stm 32 micro controller

@reinharddamon6672 Год назад

About the same problem here. When I try to import an Arduino .ino file Microchip Studio says "Unable to find the stated file". No information, which file could not be found! I assume the libraries. Why does MS not ask for the path of the libraries? (!).

@Tyros999 7 лет назад

It works with arduino due?

@larrylarson3090 6 лет назад

What port SAM AVR?

@abpccpba 5 лет назад

Way to fast for me :- (

@marathonman3095 Год назад

The sad reality of this wild adventure is Atmel can give a rats ass about Arduino community and has no desire what so ever to answer any such question about Arduino issues to anyone. All this multinational Corporation cares about is their own products and profit. Every issue I have come across have gone unanswered for well over 6 years and seem to have no desire to help anyone other that other multinational Corporations in any way shape or form. My best guess advice for all Arduino members is to completely forget about Studio 7 by way of circular file system. Unless someone can point me to a better alternative to this sad video or another that really explains the proper way to address an Arduino with their IDE. I deleted Studio 7 off my computer and have no desire to deal with the issues that are involved. Granted Arduino IDE 2 really sucks to me but at least 1.8.19 works without any such issues.