Indicator Basics - Using a Test Indicator - Haas Automation, Inc.

Подписаться 299 тыс.

Просмотров 54 тыс.

50% 1

This video gives an introduction to using dial test indicators. Whether you're measuring a part setup on your machine, or checking machine geometry as you build a machine tool, indicators are essential tools in the machinist's and machine builders toolbox.
This general information will be quite familiar if you've been taking indicator measurements for a while, but if you have someone in your shop that isn't familiar with using these tools yet this video will be helpful. This video is a version of one we use for training purposes at the factory.
Don’t miss any Haas videos. Click here: www.haascnc.com/about/Newlett...
Need more reasons why you should consider a Haas? Check this out: www.haascnc.com/whyhaas.html
If you enjoyed this video, please hit the like button and share it with a friend who’ll find it helpful . . . and thanks!
Follow Haas: Facebook - / haasautomationinc
Instagram - / haas_automation
Twitter - / haas_automation
LinkedIn - / haas-automation

Наука

Опубликовано:

4 май 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 35

@BruteEngine 3 года назад

PLEASE this is awesome. Keep this up! I want to make every FNG in my shop watch this until they can repeat it word for word.

@louistyrrell4876 2 года назад

This video has really helped me out. Honestly I didn’t know about the 12 degree angle. Thank you .

@TheDefeatest 3 года назад

Great stuff!

@raybrown5890 3 года назад

its very useful..thanks

@Hendreh1 3 года назад

Nice Video 👍👍👍

@jeffhulett4194 3 года назад

More please.

@heretohear8662 2 года назад

The video is fast, but it is accurate!!

@pratapsinhzala4875 3 года назад

Nice

@iamtemo 3 года назад

More like this

@davejoseph5615 Год назад

I've never understood why you would want an indicator that needs to be set up at some oddball angle like 12 degrees.

@joeshmoe5935 2 года назад

what if the workpiece was magnetically fixtured, would that effect how the test indicator works?

@pbc1951 Год назад

just got my first DTI ... How do I set the tip? or move the tip?

@luismaryland2305 3 года назад

Grandpa's advice voice

@johnl5177 3 года назад

hey im having issue could you guys tell me haas renshaw probe code for a partial boss probe cycle to find the center of a boss thats not fully round

@Eggsr2bcrushed 3 года назад

G65 P9823 is the renishaw inspection plus routine for 3 point vector bore and boss probing.

@davidfarmer 3 года назад

Pretty cool, but you missed one thing. A test indicator is really only intended to "test" the difference between two surfaces, its not intended for taking measurements. the reason being that it will inherently have cosine error, but when you are trying to get two surfaces to match up, that distortion to the measurement scale is irrelevant.

@haasautomation 3 года назад

David, Here are just a few instances where a numerical value is an important result of an indicator reading: Checking runout of an end mill mounted in a toolholder. Tramming in a vise on your mill table. Dialing in runout on a round part clamped on your rotary table. Checking an accurately turned or ground bore to ensure it meets a TIR specification. In all of these situations you are typically looking for an actual numerical value to assign to the measurement you’ve made. And many times this value means the part is either in spec or not. Let alone the measurements we make all day long here in the factory during machine alignment. Every one of these measurements has a numerical limit.

@norahung588 2 года назад

WOW

@arccibernardo22 2 года назад

Hello can you help me for this question? A dial indicator is used to measure ___________. A. Positive readings only or B. Shaft eccentricity, thank you, cause im confused for my exam reviewer same questions but both A and B are the correct answer, i think there is some correction there. Thank you.

@TheAlexLegolas 3 года назад

We use metric for language

@Naveenyk88 Год назад

@greatexpectations1461 3 года назад

how many barleycorns to an inch? i keep forgetting

@cvspvr 2 года назад

the number of ogre feet in a furlong is greater than or equal to the number of barleycorns in a baker's groin pouch

@thinker4life482 2 года назад

You didn't talk about the effect of gravity when using an indicator horizontally. Not everyone has a coax.

@learnrobot32 3 года назад

🤖🤖

@jacobcavanagh4501 2 года назад

Love these videos but so many are in imperial, why can't the yanks use the same as the rest of the world haha

@mrnobody6322 Год назад

@Blobby_Hill 4 месяца назад

25.4 mm = 1 inch. Do the math

@Lorgoth117 3 года назад

I guess the metric system doesn't exist...

@Robinlarsson83 7 месяцев назад

I mean, Haas is an American company, mainly focused on the American market, where the absolute majority of their customers are using dead king units :p

@IgorK73 3 года назад

I usually don't comment but there is misinformation about tip angle. First of all dial test indicator's tip must ideally be positioned parallel to surface you test, that where you get the most accurate measurement. Only Interapid and Mahr will give the same measurement up to 12 degrees. Try to do it with Mitutoyo and you will see what I mean. Interapid are great indicators but so overpriced, it's ridiculous. Not everyone can afford to buy them.

@haasautomation 3 года назад

Toucan, We specify in the video that the 12 degree alignment information applies to Interapid indicators. The reason we predominantly use Interapid indicators during machine alignment, and through much of the machine shop, is that the ability to position the stylus at 12 degrees off of parallel makes many measurements substantially easier where it would be difficult to hang the indicator off the edge of a surface to attain a parallel orientation.