Install Toni System Red Dot Plate on Beretta 92X Performance

Подписаться 1,3 тыс.

Просмотров 13 тыс.

50% 1

Took 7 months of wait time to get this fabulous plate. The installation took a LOT of hammering. I think Toni System could have made the dovetail insert slightly smaller so that it can go in easier. After all there are two set screws. If you have seen how easy it is to remove/install a rear sight for Walther Q4/Q5, you’ll know what I’m talking about.
‪@BERETTA9mmUSA‬ ‪@BerettaCommunity‬ ‪@toni.system‬

Спорт

Опубликовано:

2 апр 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 30

@HimanshuSharma-vc1bx Год назад

Very good work sir👏👏love from India😊❤

@robertpena9293 6 месяцев назад

Great video just subbed 👍🏽

@anthonynavarro101 6 месяцев назад

Will this fit a beretta 92fs? Does that plate support the holosun 507k footprint?

@burgundypoint 6 месяцев назад

Yeah

@JimmyBoomTron 7 месяцев назад

Where did you get the chrome barrel from i want to change out the black one that came with mine

@9mmtactical 7 месяцев назад

jarvis-custom.com/ Make sure you tell them what exact pistol you have so that they can ensure the best fit.

@bboyclipsy 11 месяцев назад

Hey, so how is the plate holding? I'm now deciding which Beretta to buy, a regular like yours or RDO? Did you have any issues with a plate? Thanks.

@9mmtactical 11 месяцев назад

No issue at all. It’s holding extremely well. It took me a lot of effort to hammer into the dovetail so it’s not going anywhere. If you aren’t confident of doing it yourself, you should buy an RDO version.

@bboyclipsy 11 месяцев назад

@@9mmtactical Nah I'm ok :) I have the same "wiregear" tool. Now I just can't decide on Beretta 92x Performance or 92x Centurion RDO. Somehow I like more Centurion RDO more because of the lighter weight, but I need Beretta as an alternative to Shadow 2 (amazing pistols, but design-wise it looks like a WW1 gun :D)

@9mmtactical 11 месяцев назад

LOL I know what you mean.

@JVoorhees1 11 месяцев назад

What compensater did you get?

@9mmtactical 11 месяцев назад

It’s Beretta’s factory compensator. You can see it on their website.

@ecalzo 4 месяца назад

Hi Sir , the mounting screws for the dot on to the tony system plate are M3,5 thead? thanks

@9mmtactical 4 месяца назад

Different holes on it have different sizes. For Vortex Venom that I installed, it might be M4. Sorry I don't remember and can't find the record of where I got the screws.

@ecalzo 4 месяца назад

@@9mmtactical yes, thanks that's why i am asking to you it is not wrote down in any site thev screws tyoe

@chriistar 5 дней назад

@@ecalzo Did you find any screws for this? im looking for the same

@ecalzo 5 дней назад

@@chriistar nope sir.. till now i could not be able tu put my hans on one of those

@themoistkid 7 месяцев назад

Do you think this would fit on a beretta 92fs replica Pellet gun ?

@9mmtactical 7 месяцев назад

I’m not sure. But if the slide is an exact replica, it should fit.

@mhl2674 6 месяцев назад

92fs has a different dovetail - it is less wide and I don't think would accept this plate.

@bradleywilliamson449 Год назад

How can I purchase one of these if I’m in the us

@9mmtactical Год назад

www.optics-trade.eu/us/mounts/shopby/manufacturer-toni_system.html

@dalibormotycka3037 4 месяца назад

i get the plate for rmr pattern, after instal, i couldnt zero rmr because lack of vertical adjustment, for 15m i was like 10cm up from center... 😢 anyone had same problem? or solution??? thanks!

@9mmtactical 4 месяца назад

Yes I know this issue. You probably filed too much material off of the plate? Now after you put the set screws the plate is pointing too high and you can’t lower to dot further. It will help if you have the third set screw and put it in the hole that’s in between the two set holes but behind them. That will tilt the plate a bit and force it to point lower.

@9mmtactical 4 месяца назад

Also, to confirm, did you mean that your dot was too high from the center and you can't lower it further or your bullet hole (impact point) being too high?

@dalibormotycka3037 4 месяца назад

@@9mmtactical thanks for answer, plate is tilt down, in front like 1 mm from frame of the gun, so i cant tilt plate any further... btw we didnt get any material of the plate, it sits right out of box....what i mean, my point of impact is too high

@9mmtactical 4 месяца назад

@dalibormotycka3037 oh I see. Then you can do the other way around. You can file off a little bit material from the front edge of the plate that touches the dovetail. That way after inserting into the dovetail the plate can point upward a little.