I bought these isolation dampeners, MY MIRONEY 4PCS M4 x 10mm Rubber Mounts 15 x 15mm Rubber Shock Absorber Rubber Vibration Isolator Mounts . I cut the heads off four wood screws and tapped a threaded end where the screw head was to fit into the rubber dampeners. I then installed plastic anchors into the wall board and screwed the threaded adapters into the anchors and mounted the pump. The isolation dampeners reduced the pump noise by at least 60 to 70 %. Realizing not all people have tap and die sets, perform a search for Rubber Vibration Isolator Mounts and you may be able to find the exact mount needed. Keep in mind the smaller the rubber mount the better it will be absorbing vibration.
Aspen FP1080 is a very bad pump, every year when the summer comes the pump is stuck and needs to be replaced. She is also very noisy when she works, I won't buy an Aspen pump anymore, I've had enough (4 pumps now)
Помпа очень хорошая, надёжная и простая в монтаже, но есть одно но, её чуть ли не каждую неделю надо чистить ибо эта помпа является накопительной и 20% объёма воды постоянно стоит в помпе это не выкачиваемый объём, ввиду этого в ней растут бактерии, которые попадают с водой из поддона кондиционера, вообщем образуется слизь и болото в контейнере помпы если не мыть раз в неделю помпа в последствии может сломаться.
The company that installed my Mitsubishi Split-System Heat Pump model MSZ-GL18NA installed the Aspen Mini White 83939 condensate pump. I immediately complained about the excessive noise and asked they install a vibration dampening kit because the hard mount to the interior wall allowed the wall to amplify the noise in both rooms. I was told "there is no vibration mounting kit for this pump" by the HVAC company that installed the whole HVAC system. Two months after installation this Aspen pump failed and was replaced under warranty using the same noisy model pump, again I'm being told no vibration kit is available. I'm looking for another brand that offers vibration dampening kits for their pumps. It will be worth my out-of-pocket expense when I find a suitable, quieter replacement pump with a vibration absorbing mount.
@@JimS870 I bought these isolation dampeners, MY MIRONEY 4PCS M4 x 10mm Rubber Mounts 15 x 15mm Rubber Shock Absorber Rubber Vibration Isolator Mounts . I cut the heads off four wood screws and tapped a threaded end where the screw head was to fit into the rubber dampeners. I then installed plastic anchors into the wall board and screwed the threaded adapters into the anchors and mounted the pump. The isolation dampeners reduced the pump noise by at least 60 to 70 %. Realizing not all people have tap and die sets, perform a search for Rubber Vibration Isolator Mounts and you may be able to find the exact mount needed. Keep in mind the smaller the rubber mount the better it will be absorbing vibration.
It should be obvious to you if you have any experience in HVAC. If you need to ask that question then it's better to get someone more capable to do it for you.
El diseño es elegante pero la bomba es muy ruidosa hace mucho ruido no la recomiendo para areas silenciosa como habitaciones u oficinas, ya que el ruido llega hacer un poco molestoso.
this video is useless. doesnt show how to get the impossibility small hose clamp on, or an easy way to run the wire, or even how to wire it. its for homeowners and i dont like it!
Mauvaise qualité tombe en panne au bout de 2 ans et chaque fois dégâts des eaux, les 4 que nous avons au bureau ont systématiquement lâché : en cause le plastique qui se craquellent (bacs) et le refoulement qui casse. Aucune sécurité pour prévenir des dégâts et arrêter le climatiseur.
Poor design. Loud pump and not enough of the water is drained out of the well each time it triggers. Runs every 5-10 mins when it could go twice that time if it just drained more.
