Installing Running Board Lights on a 2018 Ram 2500 

TIP : when mounting light strips to your vehicle, put a bead of clear silicone on each side of them, the whole length. The strip won't fall off later. I do lighting on pontoons and it's how I install them. Been doing it for over 10 years (probably close to 50 pontoons since) and I haven't had to redo any.

Add the running light to the fog light that way you can pick to have it on or off and would be very helpful in fog. Good video

Great video. Looks good. Personally I like the amber running board light on full time, but I do think the fog light tap suggestion was brilliant. That's the way I'm going to go.

FYI If you want to get rid of the amber running lights while driving don’t connect the red wire. You could connect it to the reverse or put a switch on it so you have the option to turn it off. Hope this help.

Thanks for the video. I purchased these lights a few months ago. between not having a lot of time and being unsure of the best way to install them, I've just been letting them sit in my garage. I was thinking about wiring them up to my puddle lights. I thought it might be easier, I don't know though. I personally like the amber glow under the truck.

Thanks for the wiring tips, I have the sequential turn signals. Think the will look even better! Going to try the install after watching your video! 👍🇺🇲

You should seriously consider adding a rubber gromet to that wire that you put through the hole you drilled into your floor. Over time, that sharp edge of the metal will wear through the shielding of the wire leaving you with a grounded circuit.

Different color running lights yeah... amber color only turn them off. Thanks for the video im looking to do the same now I know I don't have to have amber running lights but still courtesy and blinking lights

Thanks much for the vid! Very helpful...Now I really want to get a set for my 1500. I too don't care for the constant amber glow. I'm honestly not sure whether it's even legal in Maryland to have a "constant glow, ground effect". That being said, Mr. Baldwin's idea of making them work with the hazard's, is awesome! Thanks again!

Bro thanks for the video!!! I want to go overboard on installing all types of LED strip under the running broads. Thanks a lot!!!

I think those orange running lights are silly. Does the white light only come on when you open the door or do they also light up when you unlock the door using the key-fob?

Great video! How much of the running board do they actually light up? Thinking of doing this on my power wagon to light up the running boards.

I notice you didn't add a rissitor ,is it that the resistor is build in the circuit?

How do they look at night? And how well have they stayed stuck just using the sticky tape?

Great video. Could you post the link where I get those lights? I have a couple friends that we all want to do the same thing. Thanks

I would love to find out how to just have the white light come on when the door is unlocked or door is open to light up for those special black Ice moments. Would you just not hook up the other lights and it was hard to see how you actually connected them thanks though for the video something to think about. I'm not a fan of amber all the time

Great job , I would cut the red also and what you did good stuff young man.

I would have ran the wire through the clutch block off plate on the firewall like i did for my aux fuel tank toggle. Doesnt look pretty under the hood, but no drilling.

Good video but that white wire will give you problems later where you drilled a hole. With vibrations, it'll wear the wire insulation and short out on the frame. Go back and put some silicone on each side (inside and outside the truck) where the the hole is. That will minimize vibration.

Did the ground wire get spliced to the wire harness as well?

Could you remove the headlight to tap into the turn signal? I have to replace my low beam bulbs anyways

Do you think it would be possible to wire the running light option from the strips into one like splicing wires together & tap into a fuse that has power to it whenever you turn on & off your key instead of hacking into the headlights? Also was thinking of doing the same thing for the white courtesy light option, splicing the wires together but run that option off of separate switch from in the cab like on an after market fuse panel & switch box I have. I feel like it would be possible

Wait, when did you get that new truck? I think I missed that video, nice truck anyway

Could the white light be attached to be the running light and the door light?

Will this work on a 21 rebel by chance I'm looking to do this because the boss lady asked when she almost bit it on the ice

How did you pop out the light. And what color wire was it

Nice video ❤

Is there a way you can show an actual representation of how the blue splicing with the wire actually work?

How can you leave them on while the truck is on?

I wired my to the tail light taped into the negative and the runners and mine started to flickering please help what did I do wrong?

Could you hook up the running lights as hazard lights?

couldnt i run the coutsy lights for my running lights?

As far as orange glow all time mount a switch to turn on and off if wanted. Just my thoughts.

Great vid. Not a lot of unnecessary talking about personal issues. I installed mine on a 2019 F250. Undecided about the amber running lights too, since I have rocklights illuminating underneath

I hooked mine up almost the same way but I left the red wire off I did not want the orange on all the time I have a 2016 ram ,when the truck is not running the turn signal works fine when I turn the truck on one side works fine the other side doesn't work and my flasher in the truck is really fast .any suggestions?

Installed my like this work great till you turn on the truck then the lights don’t work at all. As soon as you turn truck off they work with key on? Anyone had this issue? What did you do to fix it? 17 Ram 2500

I like mine on. But i ran all my wires to my drivers side door under sill wiring harness. Easier that way,cleaner and plenty of space. I wont use those but connectors for any of my wiring. Maybe atleast go back and encase your but connector in Etape or cloth tape. But looks good tho.

So what about the right side? All wires get hooked up again, same process

Hook the Amber's up to a separate switch then.

I have a 2022 RAM 1500 Limited.. I have read pretty much all the comments. I'd like to make sure I do this the best way. I would rather run wires to the rear... But I can do front if I must. Can someone share the best way. BTW.. I have the rear tailgate OPT7 light installed with the Curt adapter #55384 Thank you,

Hello sir I did the same thing with mine that I bought and it has the same connections bud the blinkers both of them be blink at the same time so I don’t have left and right blinkers any suggestions

I have them on my truck I would leave the running lights.

There no rubber to get acces into the can from under the truck?

Turn off orange the other very cool brother

Is the right side done the same?

Are you having any issues with these flickering? I bought a set and had them professionally installed and one side flickers intermittently. If so, what did you do to fix it?

I’m assuming the right side is done the exact same way.

Leave the running lights

Anywhere in the cab to tap into the turn signal? I have the led headlights so I can’t pull the bulb out.

If u wanna do a real proffesional job please make sure u put all wires in thr plastic protectore tubing and make sure u also use silocone atv on the strips to make sure they never fall off cause that 3m strip glue will eventually fail

Turn it off Orange reminds me of a semi or industrial vehicle.

Maybe, someone could help me out? [I have worked with wires, radios and etc through my years, these are pretty simple.] "But", can't and don't understand having a issue. Dodge Ram 2017 Quad Cab I was going to run each light yellow signal wire to each headlight on the same side. Which I did. Blacks were grounded to each inner fender under the hood, as there were screws grounding other items. Red wires, (just to check) touched the positive on the battery worked, thumbs up. Thought at first tapping into the auto front running lights, each on their own side, it should be working. I'm not worried about the (White yet). So plan changed, connected the yellows together, into one signal front light. Blacks to ground. [Just to check reds together touched battery, worked great.] I grabbed a wire, hooked it to reds, ran it outside of the truck to the back drivers side tail light. Tapped into parking running light. Started the truck, worked both, but then started flickering. "FUCK". Running reds right to the battery, they work, turn truck on to run, try each signal, each works great. (But, I don't want reds going to a continuous true power, unless I hook a switch cutting the power, or it will kill my battery.) Question people, I remember hooking up radios years ago, "RED WIRE" had the fuse on it, which would need to be connected to ACC, which after turning off the truck or car, power would be dead. Why is a fuse on these lights, on black wire, says goes to the black ground??? Having the signals hooked up with yellow, blacks grounded, red straight tot he battery, turning truck on run, works, but leading red wire, to front or back tapping into running lights, so when the truck is turned on run, signals will work, when turning on the truck, the lights should continue to stay on, then hit each signal each should work. Thanks for your help, in advance. It's starting to piss me off.

Orange glow off

Might want to be careful, these are eligible in Michigan!

Leave it

There's no way they hold up in a harsh winter.

If you don't cover your splices they will corrode rather fast....shorts are fun.

theres a little rubber boot by the brake pedal, where the clutch would be. you couldve cut that for the door light. instead of drilling though the actual friggin body of your truck. good lord man

I cant hear you over the music, if you dont mind loosing the music when you talk. I turn my speakers up and up and up and the music still over comes your voice.

After a year and a half they falling off....

Any lights stuck on with anything will eventually fall off.

Leave off the music and you would have a great instructional video

Like David said, Change the running lights over to hazards.....

Buyer beware. My lasted less than a year. Customer service was just awful!