Introduction to Servo Motors and Motion Controllers 

Hey Tim, can you make a video on how to program these servo motors on Studio/RS Logix 5000? That would be awesome

If this man didn't make video's about servo's i would have cried buckets 😂😅 Thanks alot!

How do you connect voltage controller to servo ? which 2 pins ?

Hi Tim, I'm trying to synchronise 4 servo motors with ASDA-B3 controllers. Can you help me with that? Thanks

I have an Allen Bradley Ultra 3000 that suddenly started moving in the reverse when referencing. ANY idea what has happened anyone ?????

Hi tim you have kintex 5100 servo program video course

Hello Tim, How to wiring Terminal block module to PLC , I use drive Delta ASD B3 L

Hi Tim ,Just started watching your videos great info . If it’s possible can you do a video on finding servo motor ratings with out any motor name plate info on it . New to CNC machines ,trying to retro fit CNC given to me . Any info would be appreciated

Top. Do you have a tutorial on configering limit switches and homing scenario's

Hi sir ,please tell me i have kinetix 300 I have to convert it to kinetix 5100. The PLC is Micrologics 1400. How to convert this please help me

How much do they cost together, drive+ motor

Hi Tim. a video about the different types of servo motion control would be cool if you ever find the time. like stand alone servos, bus based, open architecture, ect.

i have several servo motors and some drivers, all salvaged. can you do a how to connect up and test runn. like this vid, but the analog signal thing you use i dont have will need a nother way to give that signal

How to activate R brake of kinetix5500 in run mode not just only stop mode ?

lol that was really cool! Can you please more videos about Servo motors? I have never used servo motors in my life and I have a big project coming up where I need to position a wood sawing blade on the right place. Can you make a video of how to use the positioning mode?

Good stuff, Tim. I will admit, as soon as I click play on one of your videos, I try and say, "Hi, this is Tim!" at the same time you do. I'm getting pretty good at it. My moms proud....

Hello Tim, good day I wanted to know the serial number of your servomotor

❤🤚👌🤘🤙👍🙌👐🫶

Hey Tim I was wondering if you or maybe someone you knows. Could tell me how to find the servo motors RPM feedback in real time. I have searched the Internet and read and looked thru all of Rockwell. Nothing on the topic. Unfortunately I don’t lots of money to spend on servo tech connect so I was hoping maybe you or someone here could help. I want to use the encoder that is on the motor not an external source either. Thanks.

Hi Tim, are you able to control one of these 220v drivers with a microcontroller?

Mate, this is very informative. I was having difficulties to get the idea behind the drives and how they work. Your thorough explanation helped a lot to put the bricks in place. 🙂 Thank you.

AN OTHER A M A Z I N G VIDEO that saves my A****😂!!!!Thank you for all your efforts in making these videos!!!Awesome!!! I need to control 1 of those AC servo motor with a Raspberry pi and by just listening I think I have a clue 😅: feed an analog signal(0-10V as you are doing in here) to the motor; I'm planning to generate the signal with the RPi PMW and have some sort of hardware that would eventually output a range of 0-10V signal; and that's it; I would add few buttons/switches for the enable,reset and EmergencySwitch. I'm planning all this if the actual driver/controller supports DIO and AIO a the same time 😬😬🤞🏼🤞🏼thank you for the inspiration

could do you explain about motion group a little? whats the difference between Axis -consumed, Axis servo. Axis servo drive, ....generic ,generic drive ,CIP drive?

Hi Tim, quick question for you sir. I have a Kinetix 350 attached to an Allen Bradley servo motor and whenever the MSO command is sent the Servo vibrates a lot and then faults out. However when you complete the hookup test it moves great...nice, slow, and smooth.Any ideas? Thanks!

Hello. What’s the name of the software you are using in this video. Thanks!

hey Tim for the Kinetix 5700 do you need program to tune it or make it with PID? and another thing on motion group axis Propieties>>Velocity Loop does the Hertz affect the motion if i change them and set some limit on Error Tolerrance just say 350 degre because they rotate 360 degre and with a tolerante of 10 degre ?

Tim, is there a difference between a "servo" and an "indexing servo". I want a servo to do something once it sees the Photo-Eye and gets enough encoder pulses. Then based on some inputs for start, and dwell, it cycles and goes back to a zero position. Thanks for you help.

Hi Tim, what type of servo motor are you using like dc or BLDC?

Hi Tim, thanks for the great video. I have a Kinetix 5100 servo and Micrologix 1400 PLC. I want to be able to write the speed and length values from my PLC to the Kinetix 5100 parameters. Can I do this on MSG instruction in my RS500 program? Hope you can do a video of this too. Thanks

I can’t seem to find this. I’m wanting to know how do servos have 100% torque at 0 rpm? Isn’t torque produced by the slip in rmf? I’m in school for motor controls so I have a understanding but that is way out of my learning

Hi Tim1! thanks of your great video. can you make a video about more details of the motion controller? saw in your video that you are using galil motion controller? I am still confusing of the galil motion control connection and working principal. hope you could help

Can you make a video on how to synchronize two servo motor. On CCW.

Any online programs that you would recommend for control panel building and PLC training and programming?

Hello Tim can you tell me what would cause a servo motor to set a higher torque valve as the machines get older .

What's the name of this servo motor and drive can you tell about this???

Hi Tim sir you have any servo training course in 5100 series with micro 800

Thanks tim 👍 your a great knowledgeable professor

Hi Tim. Love your videos. Can you please upload a video on a very simple servo motor programming application example using Siemens TIA Portal?

Hay Tim what is your daughter doing there?

This one really helps me like all the other videos....coz im taking motion controls courses in rockwell automation

Thanks Tim these types of videos are really good.

servo mooter

Sir, how many servo or steeper motors can we connect to 2 axis controller?

I like to know servo parameter setting in drive ,coz it's some tricky to know that

So a plc can't control a servo

Great information. Thanks

I was wondering are there any servo motors that could power a table saw?

Keep the good work!

Tim, great video. I want to replace old system with a servo system. Similar machines have a 5hp motor. The process is the servo controller gets speed information and a Photo-eye to know when item is at a certain point. Then based on machine speed the servo shaft rotates at same speed as machine to push an item up using a part attached to the shaft. I'd like to know more about servos that use a start point, speed input and rotation (stops or dwells once rotated), and it returns to start waiting for the next cycle to begin. Maybe you'll do a video on these basics.

I use kinetix 5500 025H. How to solve the S30 fault problem one motor draw other motor because they run difference speed with each servo use loadcell control speed the motor 1 draw motor 2 I see the DC bus value of motor 1 around 500VDC and motor 2 DC bus around 750VDC all time and it can run only 2 minute and S30 fault appear every cycle ?