Download schematic here: 123link.pro/AkC6Iefv (click link, click i'm not robot, wait 7 sec, clock get link - OK) Or drive.google.com/file/d/1wcgiNCD9ZcTS64AQZwx78DmQQjhfeKVz/view 12V to 220V AC sine here : ru-vid.com/group/PLrUmD1zEzCjNVgChpHzHeTNLvzBlSOqiz
Galera eu fiz um pra mim e deu super certo mas precisei de modificar um pouco esse circuito: Estava gerando muita carga (aproximadamente uns 350 volts),liguei o diodo na saída do meio do transformador e outro na dos lados (original era as duas ligarem nos cantos e a saída do meio vazia). Ai isso formou 230v certinho. Ai peguei duas tomadas que tirei de um estabilizador e liguei 1 do jeito que esta ai no video e outra em apenas 1 capacitor formando 1 tomada de 110v e uma de 230v. Gente tomem cuidado depois de desligar o circuito,pois os capacitores se mantém carregados por um tempo.
Super génial pour les chercheurs en Energie renouvellable et économique.Encore un coup de pousse les gars vous ouvrirez pas mal des portes .Car.la lumiere c'est la vie.
11:05 On your circuit at the output of the transformer, it is a voltage doubling rectifier. That is, the voltage will be multiplied by 2 times. Moreover, through the rectifier, the voltage will be multiplied by 1.4. That is, in the end: 220v * 2 * 1.4 = 616v ?
When it is unloaded, I have about 380V output, and when I connect a 25W / 230V tospada bulb to about 165V. When I connect a laptop turned off so that the battery recharges itself, it drops to about 150V, and the current flowing at the input is about 4.5A and the supply voltage is about 13V - 14V. I will test it with a 4.5 A and 15 V laptop power adapter - media tech. You have a 100W light bulb and it shines nicely and the voltage is 220V. For me, the laptop xachilacz 90W and 19V output.
Amigo, na boa, vc pode continuar sem falar, mas melhora o.propósito desse e de outros videos, detalhe mais as referências do que é usado, com textos e também com zoom sobre as pecas, as ligações,vvai o like mas melhore ae, agradeço pelo post
Это не инвертор, а повышающий dc/dc преобразователь. Ведь, на выходе постоянное напряжение, судя по вольтметру. На экране DC горит. Но, всё равно, лайк)
@@E-mtb99 Зарядку от телефона точно будет питать, только вилку нужно подключать в одном из положений + - или - + .... Жк телек в теории тоже должен работать, но есть риск спалить блок питания телика и вилку подключать в одном из положений... Старый телик не будет работать.
Ребята конешно постоянка, тут и речи нет о мультивибраторе видать такая цель отсутсовала . Проще обычный умножитель собрать и меньше времени займёт, но для начинающих пойдёт! Лайк за труды
nicely built, however, considering your transformer size, i think its from 12v 10 amp atx power supply, which means you can only get 120watts of power at best, besides, most atx supplies use power transistors, unless u have changed the transformer winding to use with mosfets , this cant out put more than 120 watts
Looks great however, from the video I cannot tell what the other ends of the black and red alligator clips are connected. I assume it is a 12 volt battery. Does their polarity make a difference ? If it is connected to a 12 volt battery , what is the life of the battery if for example the power derived viz 220 volts are used to run a 220/240 Valve radio ? Regards Baldric aka David
How many amps does it pull? Any losses in amps available. Such a large jump in volts means as much loss in amps. So will this only power a small bulb or can a larger transformer be used? 👍
Hello friend, how do I know the 12 v winding and the 220 v winding? Can you measure how many ohms each 12v and 220v coil has? If so, would you tell me how many ohms each winding has?
Hi friend, what power does it arrive at? All the investors that I found up to this moment are only good for 6w led lamps as much. excellent video I will test your circuit to see how it turns out. regards
well a step up of sorts? i believe so and not that difficult to put together... to test but i believe that could run a universal AC washing machine motor at the same speed that runs with AC which means 12.000 rpm.....well if not that fast at the very least 6.000 rpm. thank you for sharing,very appreciated!!!
With this method, what does the output wave form look like on an oscilloscope? How smooth is it under load and how is it for EMI? And what frequency please?
I think the AC output voltage is about 110 volt only and by adding two capacitors in serial . They double the voltage. How much current in the output or how is tha wattage? in the schematic you used -12v for the negative and +12v for the positive which is 24v. Ca we use only 12v ? Thanks for the wonderful idea. It look exactly as the heater induction, correct me if i'm wrong :)
Yes, you are right. I used 2 capacitors and 2 diodes to increase the output voltage. The output current is about 1A. I have a habit of writing -12V instead of GND. This circuit uses 12V voltage from battery. This circuit is ZVS. It is similar to induction heat
Funciona perfecto , pero tengo dos consultas. 1. Por que se calienta una de las dos resistencias de 220 , casi quemándose . 2.si pongo un capacitor más a la salida , la energía sería más limpia?
poner mas capacitores de esos no ayura en mucho. depende que sea lo que entendes por limpia si es por la señal. pues no no sera sinosoidal y la frecuecia talvez sea muy alta para limpair como decis hay que pasarlo por un transformador de hierro al silicio los grandes en relacion 1:1 por que ya tenes los 220v aun asi no se si limpiaras la frecuencia
This Circuit has plenty of Power but the frequency is much to high to drive any inductive load. You can power a light bulb with it but no motor. Still not bad
Aclaremos que eso no es un Inverter... En el Inverter en el primario tenemos corriente contínua y en el secundario corriente alterna... En este circuito tenemos corriente continua en entrada y salida... Esta es una fuente Step-Up
It is DC voltage. You need H bridge to convert 220V DC to 220 AC. But DC voltage can be used for light bulbs, televisions, phone chargers. Do not use for fans.
@@PhdHung ok, thanks for that, but i wouldn't use dc 220 for my tv, even if my tv used 220, i wouldn't put dc into it, phone chargers rely on ac for the step-down transformer to work,
Por que não mostrou a fonte de alimentação de 12volts ? Não vi circuito oscilatório algum esses mosfets do Dissipador de calor trabalham com PWM. Agora digo cade esse circuito de oscilaçâo ?
HI SIR VERY GOOD IDEA . CONGRATS. I HAVE A DOUBT. MAY I USE THIS OUTPUT TO DRIVE A LAPTOP CHARGER? SO THAT I CAN USE MY LAPTOP IN CAR. WHAT IS ITS POWER OUTPUT? HOW MANY WATTS?
You can connect any switching power supply in its output. These supplies do not care about the shape or frequency of the input voltage. About the wattage, he says somewhere in the comments "200 Watt maximum".
Welcome. What transistors? Mosfet? Bipolar? IRF ....? 470Ω + 470Ω resistors in parallel = 235Ω did you give? I G - S 100Ω? 220V under load. I did the same and I only have 170V, but the laptop works. Only IRFP240 I gave RDSon 180mΩ. Regards.
@@pantowerpantower им можно питать пассивные нагрузки типо зарядники а если убрать диодный мост А так схема достаточно распространена работает по принципу блокинг генератора
I don't see how this would even work, you need an H bridge setup in order to make an on/off configuration because transformers don't work on DC power it has to be AC power. Also you have to have a microcontroller to set the frequency of the H bridge to get it to do 50/60Hz.
Hi bro,great job done,can u plz give me detail of every single cc component use in this video,because i got power supply from market and resistors but now power supply lil change,kindly help me.
component here: 123link.pro/AkC6Iefv (click link, click i'm not robot, wait 7 sec, clock get link - OK) Or drive.google.com/file/d/1wcgiNCD9ZcTS64AQZwx78DmQQjhfeKVz/view
Buen proyecto.pero no se aprecia las conexciones .si tuviera un esquema o crokis estaria mas completo .de todos modo esta muy bien gracias x compartir.un saludo.
uma duvida my friend?aos 6,:45min?qdo voce une os resistores,dessa forma nao anula a resistencia?nao teria que uni los em serie ao invés de pralelo?tente medir a resistencia deles para ver ok?Sou iniciante,ja fiz assim e medi e parece q fica o valor do menor resistor e nao a soma dos dois?goodlook...
Здравствуйте у меня инвертор от солнечной панели он гудит и лампочки мигают 24 вольт на 220 .3000 ват причина В чём не знаете такими не сталкивались после дождя так стало гроза была у них предохранитель что-нибудь есть
Gostaria tmbm de trocar ideia com interessados no assunto pois qero montar um pra mim..ja tenho algumas peças aq...só preciso da referência de cada uma qe foi usada no projeto
Hi i open a 1kw solar inverter and there are a glass diode in tupe stick on just one power mosfet .i have a question ,what kind of diode does it??cause its broken Thanks
Pero en el diagrama tiene la última etapa un doblador de tensión o algo así y los condensadores electrolíticos con diodos semiconductores que se usan ahí, polarizan la tensión de salida en Positivo y Negativo y dice en el plano: Salida de 220 VDC. ALGUIEN QUE ME ACLARE POR FAVOR. But in the diagram the last stage has a voltage doubler or something and the electrolytic capacitors with semiconductor diodes that are used there, polarize the output voltage in Positive and Negative and say on the plane: 220 VDC output. Someone to clarify the question please.
Puede w sea bueno pero la esplicacion es muy mala coloca los cable y las pieza y no indica en w punto van y de paso está oscuro para ver onde ensi va las lieneapo e favor mejorarlo
You should add in description that ! you can damage your devices with this ! Without load on 220V side Voltage will be ~400V bcs is not stabilized. Thats why there is so many electronics in inverter. I don't want to write about it just read why this is dangerous.
thank you i got 12 volt from the power supply of the computer i used it to charge battery(12 volt 7ah) but the amber of the power supply is 2.1? is it problem