iPhone XR Back Glass Replacement (How to fix the back for $15)

Подписаться 32 тыс.

Просмотров 35 тыс.

50% 1

Today I am going to show you remove and replace the back glass on the iPhone XR. For those wondering, I used a 1500W Dual Temperature Heat Gun (which costs about $11-$20) and had it on the highest level. If you are not all right with opening up your phone, do not proceed!
Unedited Video of me removing the back glass from start to finish, for those that need it - • iPhone XR Back Glass U...
Required tools-
PH000 Bit
Pentalobe P2 Bit
Y000 Bit
Stand-Off Bit
Pick
Razor Blade
Xacto Knife (below)
Glue (below)
Heat
Protective Gear!
Patience.
Check out the RWR Discord! - / discord
Support the channel via Patreon! - / realworldreview
(affiliate links)
***Part can be found here (all affiliate links);
For some reason companies are selling with adhesive, you can do that or glue, up to you. I choose glue.
Black - amzn.to/3cX6coL
Blue - amzn.to/3iSJbHt
Coral/Pink - amzn.to/3qdWBiE
Red - amzn.to/3cUFZqY
White - amzn.to/3cULs0K
Yellow - amzn.to/3gHapzj
Protective Glasses - amzn.to/3pcoYMV
Protective Gloves - amzn.to/39Xybm2
Xacto Knife - amzn.to/2M2dvkG
#18 Chiseling Blade - amzn.to/3sPqDuf
Toolkit that works for this repair (affiliate link) - amzn.to/2TY9fBD
Toolkit that I recommend and reviewed (affiliate link) - amzn.to/2EqCvvv
Toolkit that is closest to the one I use for all my repairs (affiliate link) - amzn.to/2H4duIr
The glue that I recommend using (I use the B6000 at 50ml, but B7000/E6000 work as well) (affiliate link) - amzn.to/2GY2cVL
Clamps I recommend with the glue (affiliate link) - amzn.to/2T8opHn
Dual Temperature Heating "Thing" (Heat “Gum”) (affiliate link) - amzn.to/2FMUfly
The best type of razor blades (buy 100+ cause they’re low cost and fragile[don’t pry with these!!!]) (affiliate link) - amzn.to/2YE4W17
Toolkit that works for this repair (affiliate link) - amzn.to/2TY9fBD
Toolkit that I recommend and reviewed (affiliate link) - amzn.to/2EqCvvv
Toolkit that is closest to the one I use for all my repairs (affiliate link) - amzn.to/2H4duIr
What else should I teardown or fix? Want more iPhone videos? Let me know on here or on Twitter / mattofrwr .

Наука

Опубликовано:

1 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@boydjosh5662 3 месяца назад

This video was gold, full dissemble and reassemble with commentary. Have taken apart my XR and back together fully once now with this video. Turns out I gotta tear it apart again so here’s round two

@henriksvensson2836 6 месяцев назад

second time doing back glass replacement with my first laser as a total beginner, had to laser it twice then i used knife for about 1,5hours and voila finished like new :)

@randyaven6377 2 года назад

Holy Crap! I think I'll just take it into a shop. *sigh*

@nwindianasirens4012 3 года назад

Apples glue on the back is stupid strong. Not bad but a laser machine is always preferred. And have a vaccum near as shards go everywhere

@jaysonpriest7094 Год назад

Why is it so necessary to remove all the components? im assuming it has to do with the heat being applied?

@NeOAnderson 5 месяцев назад

It's for extra protection from burning the components. But, if you're careful and don't apply too much heat in a specific spot ESPECIALLY around the sensistive parts, like the camera area and the bottom charging port area, you should be fine. I've almost finished one just now , first time. It was so painful to get the glass out... probably not usin enough heat but was worried I'd burn something under the glass. Ultimately, it is almost complete (need to glue new cover back on) and it was all okay.

@NeoOwnz 3 года назад

I did that once and never again. A full housing frame swap is best if you don't have a back glass laser machine. You basically took the entire phone apart so just put it back together in a new housing assembly.

@kelpodelpog5395 Год назад

Where can you buy it

@patrikboubin8083 10 месяцев назад

only the price differs a lot

@juliannabrown2073 2 года назад

while putting the inside back together the charging port black strip directly connected to the actual port ripped. what do i do now??? can i glue it? Solder it?

@RealWorldReview 2 года назад

Replace with a new one, the whole port cable