Тёмный

Kawasaki Mule 610 engine install/removal & Driveshaft Carrier Bearing Install/Removal!! 

Good Timen Tools!
Подписаться 860
Просмотров 14 тыс.
50% 1

Опубликовано:

 

28 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 12   
@mikelandry2234
@mikelandry2234 2 года назад
as soon as you started talking i knew you where from louisiana
@rodgerlarsen
@rodgerlarsen 11 месяцев назад
Hey Ryan. Great video. I'm from Plaquemines parish and i have a 2014 610 mule. I bought it right after Isaac. it runs great but recently (I hunt in alabama) it is struggling to get up the hills. It's not starving for gas (sputtering, backfiring or running rough) its just losing all of it power before i can get to the top and might have to go into low gear to finish the hill. also i kinda smell like an oil leak but no oil anywhere. i read some things talking about the crankcase vent. do you have nay ideas? thanks Kenny
@willis_lots
@willis_lots 3 года назад
thanks for your time
@jeaservices
@jeaservices 2 года назад
How do you align the front and rear drive shafts. I know , NOW, that you're supposed to mark them, but I didn't. Now I have a vibration.
@mikedill7378
@mikedill7378 3 года назад
This video helps me alot....thanks for making it....I just got one that burnt in a fire pit....know I get to see how it looked before the fire...only the frame and transmission was salable.....now just two wheel drive.....steering and front diff melted....so now has quad front end and steering....add a better front diff in the summer........this governor on the transmission....under the black box.....I have seen video to adjust that to bring up the speed from 25 to 38 mph....can you help me understand how that works....is it only engine rpm....or changing gear ratio's?....that would help me lots....I also have to do the front drive shaft...change same part...and u joints....that helped as well.
@dictumfactum9468
@dictumfactum9468 3 года назад
Not a lot of repair instruction out here. Thanks for posting. Did you bore the cyl? New piston or just rings?
@goodtimentools619
@goodtimentools619 3 года назад
No, I got lucky. The cylinder was in good shape. I took a ball hone and did a light hone to it. I did go with Namura piston and ring kit on it.
@dictumfactum9468
@dictumfactum9468 3 года назад
@@goodtimentools619 Cool. Where do I find Namura parts? Are Partzilla stuff any good? thanks.
@goodtimentools619
@goodtimentools619 3 года назад
@@dictumfactum9468 My Bad work got hold of me. The customer had got the top end. You should beable to find them on Ebay. Yes, Partzilla is good parts. It's OEM parts.
@craigwoods8500
@craigwoods8500 3 года назад
How did you remove the front drive shaft from the differential?
@goodtimentools619
@goodtimentools619 3 года назад
If i remember correctly, it should just slid off once its unbolted
@jeaservices
@jeaservices 2 года назад
There's a single pin bolt that holds the u-joint housing on the front end.
Далее
Kawasaki mule carrier bearing
8:37
Просмотров 11 тыс.
无意间发现了老公的小金库 #一键入戏
00:20
how to mule transmission teardown 3010/2510
7:45
Просмотров 20 тыс.
Bought a 2006 Kawasaki Mule off Craigslist.
13:23
Просмотров 5 тыс.
How to Remove a Kawasaki Mule Engine(Gas)
10:20
Просмотров 10 тыс.
Replacing a drive shaft U joint
16:18
Просмотров 196 тыс.
Kawasaki Mule 610 Engine Rebuild!!
12:35
Просмотров 9 тыс.
mule transmission rebuild
8:31
Просмотров 6 тыс.
Will It Run? Kawasaki Mule 550 UTV
25:12
Просмотров 1,5 тыс.
D.O.A. Kawasaki Mule - Carb Rebuild and First Start
24:27
Mule 610 Primary and Secondary Clutch Rebuild!!
15:52