Kubota Hydraulics Cylinders Part 3: Reassembly with New Seals and Rods 

I'm a retired forklift mechanic and I used to do the same thing with needlenose pliers. I wish I had a tool like that. It would have made the job easier, especially with small seals like that. This was the first channel I subscribed to years ago and is still my favorite. Other RU-vidrs I watch have said similar things about this channel.

Always amazed those seals tolerate being folded during installation. Those seal install assist tools are pretty slick.

I've been looking for 28mm chrome rod and found it at CRC. Thanks for the tip. I told Jake I saw your video and he was stoked you gave them a shoutout!

Adam, passionate, focused and knowledgeable about his work. Great filming. Fun to watch .

Being a heavy duty mechanic I have done countless hydraulic cylinder seals. The small ones such as you just did it’s absolutely helpful to have the seal installers like you showed. It can be done without but it is not easy to do. The proper tool makes is so much easier without damaging the seal. Very nice video series 👍

Didn't knew there was a Special thread for those caps. Thanks for teaching us so much every single time

I have a kubota tractor, and none are leaking, but I now feel that if one of them starts leaking, I can fix it. Thanks a lot for sharing your knowledge.

I have two Kubota tractors, now I know more about them. Thanks!

Working in my trade for almost 40 years manufacturer’s always taught me the most common failure to oring is a rolled oring during installation We were taught to use a pick or similar tool to install them similar to how you were installing the seals with your ice pick start at the top and using the tool to work the oring down into the oring groove Some orings actually have a painted stripe around the outer edge in order to verify the oring is not rolled and twisted in to position

Always Good To See Something Rebuilt Instead of Just Thrown Away..Especially Now Days where people/Tech mfg's seam the think Every Thing is disposable ..use it for a year or two n jst throw it away & go buy a new one !

It helps to warm all the seals when installing hydraulic seals. Nice job.

A master class on installing o rings and seals

I work at a shop that built all hydraulic cylinders for fork lifts .We use only use nylon locking crown nuts on the rod ends . Even three stage container stacking lifts

That's what I needed! Great video! I've rebuilt rams before but that one little thing you did clamping them to the table to put the deals on made my job so much easier! Lol It's the little things!

As an aircraft mechanic, I have resealed hydraulic cylinders many times. Your practices and procedures are spot on. Good job.

Dobra robota i ładny czysty warsztat z przyjemnością się pana ogląda pozdrowienia z POLSKI

Great tip about using putty to get accurate caliper measurements! Excellent video series. Thanks for all you do!

Thanks for a clear demo of the use of that Kit King tool. Happy I saw this before using one for the first time.

It'd be fun to see the tractor in action again. Maybe just a minute at the end of a video. Always great to get to watch people who know what they're doing work on things.

Adam go to a thrift store or yard sale and pick up a used crock pot, works great for heating oil for what you are doing

I had forgotten all about preheating them but when I was young I remember seeing someone using a small crockpot.

first time I saw that tool at work I was slack-jawed. My coworker laughed his ass off!

Ordered a shirt yesterday and here within a minute of uploading today. I'm on a roll

Use a small diameter o ring and wrap it around the piston seal, put your finger through the o ring and pull the seal over the piston and into the groove, let one side of the o ring go and pull the o ring out from under the seal. No need for picks or screwdrivers.

I always love seeing the old pic of you at the end of your vids. Great tribute to the men who helped you become who you are.

Great job like allways. Thank you vdry much for sharing your videos. Just a small remark about that aditional seal you machined in between the piston and the rod: I'd say that is now overengineered 😉. Even without that aditional seal it would work perfectly. The treads are sealed with the loctite and in betwen the nut and the piston, even if you have a leak, that will be so tiny that it doesnt affect the function at all. You will have much bigger leaks by design betwen chamber A and B of that cylinder on other places. For example over the valve and after some time and wear over the outer piston seal. After all, nicely done but for the function not really necessary.

EXCELLENT VIDEO! USING THAT GREASE IS THE WAY TO GO AND THE WARMING OD THE SEALS IS SMART, THANKS

nice trick with heating the oil to soften up the seals

fun to watch and gives me enough info to tackle cylinder reseal on our old tractor with more ease ...

Something no one seems to have mentioned is that in hydraulics, cleanliness is everything. For that reason I suggest plugging the cylinder inlet and outlet ports once the cylinders have been cleaned internally, before you start assembly. The plugs might blow out when you insert the pistons and rods, but these orifices should be plugged again when assembly is completed.

That pot is still good for boiling shrimp, they'll just taste like they came out of the Gulf of Mexico...😆😋 they're called Deepwater Horizon shrimp...

Man living in the midwest I never seem to get cylinders apart that easy

Hi Adam, nice job. 1.But the rods can easily be saved without buying new ones. 2. You can heat up all sealings (Teflon, Ceramic…) in an oven to expand, but you have to reset them to the right dimension with special grips and cool them down. 3. Assembling the sealings, o-rings, wipers… always with oil not dry. Never use a screwdriver or something like that (nothing itchy or scratchy). 4. To assemble all parts use hydraulic oil not the coloured grease. You can use additional a Lithium- Grease for bigger parts. 5. You should use a copperbased grease for screwing the cylinder. 6. Please never push and pull a dry rod (the grease will set into the honed cylinder after inches) . 7. Finally you should mark the cylinder screw with a punchmark to control that it will be sitting well (they get hot). Just a few hints from a pro who made thousands of them…not only this simple ones. For more info just ask, always a pleasure to watch your channel. 👍🙋‍♂️

I use petroleum jelly it won't clog valves and it will dissolve in the hydraulic oil. Also the reason there was no oring under or sealing between the piston and rod is because they had a tight fit between the piston and shaft and when tightened up it will seal it self but oring is always a good idea And better than lapped surfaces. Love your work and your shows .

Crazy how those seals can hold that kinda pressure

Some seal manufacturers are okay with using boiling water to heat up the seals. Some of the equipment I work on recommends it. I I got a little electric kettle so I can do seals indoors. Oil is better if the seal will stand it because you can get the temp a little higher, I put the seals on a piece of wire so that you don’t have to fish them out or burn yourself at the end. Then on install, if you have access to nylon bars, you can cut it down so that it is tapered on top and the bottom of the nylon goes up to the edge of the seal groove. Then just rub a lot of oring lube (molykote 55 is my favorite) on the taper and it will slide right on. The real a-hole manufacturers will then force you to resize the oring smaller, they make tools for this but a proper size hose clamp and thick plastic from like a gojo jug works fine. Since you are only doing 4 pieces it’s not worth the effort to make the tools. Always enjoy your hydraulic cylinder videos.

Excellent video series. Thank you sir.

Thank you Adam I enjoy learning and watching your wonderful videos I am from South Africa

Thanks for the tips and tricks of getting the seals to pop-in.

Thanks for the excellent details on rebuilding the cylinders.

A few days after I watched this video, I had a cylinder start leaking on my kubota tractor. This video series helped save me a lot of money by rebuilding them myself instead of buying a new cylinder

Coffee cup electric immersion heater in an old cup with hydraulic fluid. Don't accidentally let the seals rest against the element. Don't accidentally drink. Works great.

Have 2 leaking cylinders on my grapple bucket for my Takeuchi TL8 CTL (skidsteer). I think I will give this a try in the home shop and see how it turns out. Great videos!

Great job as always! My OCD is screaming for that paint to be completely removed 😂

better than factory for sure!

Congrats on half a million subs Adam!

Great job as expected. All your tips and advice throughout this build are just a sample of your workmanship and professionalism. Everytime I watch you turn a piece of steel into a workable finished piece, I just realize that's how it's made. Thanks for always showing what needs to be done to get to your finished piece. Your tips and advice come from years of experience. Can't thank you enough for showing and explaining why you do what you do. I always look forward to you Saturday afternoons.

You havent lived till you had some chicken wings fried in Hydraulic oil!

It’s satisfying to watch Adam work. It must be very satisfying for him to obtain such a result.

I use a little electric fry daddy. When you're done put the lid on and set it in the corner works really cool

Fantastic video and step-by-step instructions. I used your videos and was able to replace the seals on my LA680 front loader. I especially liked the technique of heating the fluid and warming up the seal. It made installing the seal so much easier. Thanks again and keep up the great work!

I learned this from a old aircraft mechanic when rebuilding landing gear hydraulics and struts and if I had that tool I could have shown him a thing or two, now that would really make it easier. Thanks for sharing your experiences with us.

Sehr gut mach weiter so!!👍👍

14:40 You hear that click? Thats torqued to 1 Abom.

excellent information and instructions. Quality craftsmanship. The additional O ring on the piston is a wonderful addition.

Loving this content. one of my favorite channels. Thanks for uploading

Along with warming the seals in oil you can also put the pistons in the freezer for a few hours and that helps too.

Helpful and informative as always!

Noting like a nice tight seal around your rod

Отличная работа!

Adam, Another fantastic video, And well done project. You never fail to teach us something every time you post a video. The warmed up oil trick is epic to fighting with tight tolerance seals and o rings. You have become a heck of a teacher Sir.

Wow! a tool for every job.

Thanks for sharing! Great follow up !

Another excellent project series. Well produced and edited video with great sound.

Small electric coffee cup warmer plate and cup heats seals perfect

Looks like they are nice and smooth! Nice work, Adam!

I always replaced seals with Viton seals. They take a much higher temperature, upwards to 400 degrees. Very good idea heating them in an oil bath.

Adam: "Отличная работа!" Russian for "Outstanding work." Thanks for the video. Sorry you weren't at the Bar-Z this year. Jon

nicely done, sir. solid series!

we always used a fry-daddy with hydraulic oil in it to heat seals or bearings. you could set the temp to what ever you wanted

That's a cool tool for installing seals. I find a little bit of hydraulic oil on the seals when installing can help a lot to slip them into place, also helps prevent them from scratching on sharp edges. Thanks for the video!

Nice work thanks

Adam, make a tapered install cone from nylon or Delrin then use that to gently stretch the seal as you slide it down the cone onto the piston, the bottom of the cone being the same diameter as the piston.

Another trick I have picked up with installing o-rings is to use wire lacing to install. It adds little to the strech of the o-ring and allows more strength that will not damage the o-ring. Then you just pull the lacing out when you get the o-ring installed.

Great idea about using hot oil to warm up seals. Another useful tool would be o ring picks they help grabbing those seals without marring up too much. Also a bearing driver set that covers a large range of diameters to help if you have to change a cylinder that has a wear bearing.

Great series

Nice work Adam...

If you used a large washer between the clamp and the piston ,offset over the edge of the piston ,it would hold one side of the seal in place as you mount the other side of the seal. I would also put the piston back in the hot oil after fitting the seal. Most polymers will not fully relax back to their original size if they are softened with heat ,stretched and allowed to cool in a stretched state. They need to be reheated to allow them to relax. This is how heat shrink materials are made. If you heat a soda bottle it will shrink back towards it's original size.

Great job Adam. Awesome video and a great help

Awesome work Adam

Great job Adam!

Next time on abom79, we steal another of Abby's pots and heat up salts for heat blueing steel! 😊

I have that seal installer tool I find that on smaller cylinders it’s handy but on big stuff like 100mm rods or bigger it’s better with your fingers. That seal will just constantly flip because they are so big for those tools.

Outstanding job 👍

I use an electric skillet for warming oil and also as a bearing heater. Works great.

Fine Sealmanship!

Jimmy's ice-pick comes in useful quite often for me. Cool to see you got one too.

I like the warning about pipe wrenches and chain wrenches.

As always a very nice job Adam.

Great info.

Very interesting right there.

The authority on the correct way to do machining operations.

Thank you, I learn a lot

Nice work!

I used warm water on a hot plate. Around 180 degrees was perfect. Our shop had a shop made hydraulic piston nut bench. Some of the excavator cylinders had crazy torque up to 25,000 foot pounds on the rod nut. That hydraulic wrench was slow but it either loosened or twisted off. Most times the rod was gouged, nicked or bent.

You made that look easy.

Always like to see the finish product in operation. A put the minors back to work video would be interesting, and satisfying. Thanks again for providing the interesting and entertaining content.

Great job.

Dang it that was fun Adam! Zen of oleo strut refurb. Thanks from Rocket City.

great work ! , very intresting ! .