KYOCERA FS1035 FS1135 M2035 M2535 ERROR C3100 

@kakazu65 Printers can usually be repaired easily.

@@MrRicoh oh for sure! That's why this error had been driving me mad!

It's most likely a hard disk error. Try getting the HDD replaced.

There is no CF100 code

Take out the Drum Unit and move the electrode cleaner to the side :) That's all. Tell me if I was right.

Y con el genérico me dice que recatgue

Si puede ser. Instale un tóner nuevo y estará bien. Este es un mensaje que indica que la copiadora no tenía el software actualizado. No te molesta en absoluto. Aplique un tóner nuevo y estará bien. Check out my gadget store 🤩🥳 MOVIE STUDIO SHOP: my-store-7469644.creator-spring.com/ 🔥🔥 RU-vid SUPPORT: ru-vid.com/show-UCOHtXTtGHj33pUm8Gf2FH3Ajoin 😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio 🔥💥 PATRONITE: www.patronite.pl/1796

Recuerde que el tóner debe tener un chip nuevo. El chip es un trozo de lámina negra en la carcasa del tóner.

I'm afraid this is a more complicated problem and you'll need to call service.

Enter service mode above 900 and it's there. You can only use the reset once, so if it doesn't work, it means that someone did the reset before you.

Super! 🔥🔥 RU-vid SUPPORT: ru-vid.com/show-UCOHtXTtGHj33pUm8Gf2FH3Ajoin 😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio 🔥💥 PATRONITE: www.patronite.pl/1796

I am very happy that my movie helped you repair the printer. It is very important for me to have every hand up or subscribe to my channel. I'm doing my best and best regards.

@reverienmwongezadembe1349 Sometimes the output sensor breaks and the printer jams the paper in the Fuser Unit section. Sensor or spring.

Do not understand the question. The toner has the symbol TK-1140. Have you asked about it?

@@MrRicoh Yes sr.. Sr. Can I talk with Hindi....

Write in your language and I will use the translator.

@@MrRicoh sr. Mere pass Kyocera FS 1035 MFP Xerox hai.. Jisme TK-1144 ka cartage lagaya hai.. Mera sawabal hai yea install ke time koi v install number use Nehi Kiya hai.. Abhi print quality bilkul low...aaraha hai.. sharpness bilkul v Nehi... Keya kare sr... Plz.. help me...

This is a very common vulnerability. I have already replaced the RADF-copier connecting cable many times. I mean this: copy-expert.com/pl/c/Przewod/218

I showed it in the movie

how to reset fixed kyocera 2030

Kyocera does not have error 302. Are you sure=I know you provided good information?

What have you been fixing? And what do you want to reset?

1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. CIS - Main/Engine PWB (YC506) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the image scanner carriage and execute U411.

@@MrRicoh Thank you..

Welcome :)

Look this: www.copytechnet.com/forums/kyocera-mita-copystar/108415-cf000-multiple-kyocera-fs-1135-a.html

1. Clean the optics mirrors 2. Clean the charging electrode in the drum unit. 3. Check the photosensitive roller in the drum unit, if there are lines on it, it needs to be replaced. 4. Check the heating shaft in the fuserunite, if there are lines on it, it must be replaced.

Sumulat ka ng napakaliit. Ano ang error code? C400, C50, C100? 🔥🔥 Channel Memberships - RU-vid: ru-vid.com/show-UCOHtXTtGHj33pUm8Gf2FH3Ajoin 😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio 🔥💥 PATRONITE: www.patronite.pl/1796

1. Clean the optics mirrors 2. Clean the charging electrode in the drum unit. 3. Check the photosensitive roller in the drum unit, if there are lines on it, it needs to be replaced. 4. Check the heating shaft in the fuserunite, if there are lines on it, it must be replaced.

O que está errado?

Just unlock the yellow protection Best regards from Poland and good luck. Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/ #RICOH #COPIER #PRINTER #DRUM #TUTORIAL #PHOTOCOPIER #TRANSFER #COPIERPARTS #COPYEXPERT #JEMIOŁEK

Mój film nie pomógł rozwiązać problemu?

Replace the LSU laser unit

10871087 u163 and clear

Is this the whole error code? C6 only?

Is this the whole error code? C6 only?

Is this the whole error code? C6 only?

You have a problem with the thermistor, replace the thermistor or the entire fuser.