Lawnmower Leaking gas out air filter

Подписаться 135 тыс.

Просмотров 366 тыс.

50% 1

Video has a lot more talking/narration. Let me know what you think;)
amzn.to/2LQSSpG Hansen Socket Organizer trays
amzn.to/2M4LAvk Tool Cart Specs.
amzn.to/2KgZCrW Briggs and Stratton Float
amzn.to/2Kd9qU0 Briggs Needle and Seat
In this video I show you how to stop a briggs carburetor from leaking gas.
Help support Doublewide6 Repairs LLC by sponsoring his Patreon account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.

Опубликовано:

31 июл 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 234

@doublewide6 6 лет назад

@matthewsantandrea9066 3 года назад

Do you have a link for the lift that your mower is sitting on or is that something you crafted? I need one.

@daveymercer2087 3 года назад

A 1

@landenemmitt3729 2 года назад

instablaster.

@spetsovich 5 лет назад

Thank you so much for this fix. My bowl was not floating correctly, stuck open. Resulted in mower dying and fuel gushing out the air box. Changed the needle seat gasket now everything peachy! Mowed for over half hour without any issues. Now on to fixing the tranny cable and belt. Good times. Thanks again, keep up the good work!

@timothycheney9480 6 лет назад

That customer should be really happy. For him a quick fix, for us another very informative video. Thanks!

@michaelbedell6523 2 года назад

Great job, perfect down to earth explaining. I already knew how to refurbish mower carbs, but the air flow test was a great take away. Now to work on mine, as the season has just ended here in the South.

@aleblanc3547 6 лет назад

In my experience most of the problems with those small mower engines are the result of bad fuel and the resulting damage it does to the carburetors. I'm fortunate and have easy access to reasonably priced non-ethanol fuel, so I have hardly any problems with my lawn equipment. I'm actually surprised at how bullet proof these small engines are these days. They won't last 50 years like they used to but there's no reason you can't get 20 years service out of them with simple maintenance (oil and air filter changes and by using good, clean, fresh fuel.) Thanks Bob for taking us along on this one.

@doublewide6 6 лет назад

No problem.

@richardirvine1435 2 года назад

Nice job! Thanks for the video, saved me a lot of time and money. I would have totally screwed this up! Lol

@sarahhicks5188 2 года назад

I have an older 190cc B&S engine on my pressure washer. Same issue. Cleaned carb, replaced gaskets. Leak was better but not fixed. Your explanation of the float & needle seat function really made me realize I have same issue. Thanks!!

@100PercentOS2 5 лет назад

Thanks. I learned a lot and especially about floats. Seem like newer lawn mowers and lawn tractors are full of cheap plastic parts.

@erwinsu6101 4 года назад

Thank you. I went ahead and replaced the entire carburetor but your video pointed me in the right direction.

@zinnstigertownmowers780 6 лет назад

Getting back into the swing of things I miss seeing you just been busy that’s still a nice mower

@kp57_what 5 лет назад

Thank you for making this video! This is exactly what happened to me yesterday.

@alexanderpendjurin1880 Год назад

Thanks for the great video. I have a Lawn Boy mower with a Kohler XT149 engine that leaked gas out of the carburetor. The gasoline also made the air filter rubber gasket swell up and not fit in its housing properly ... I ended up buying several air filters until I fixed the gas leak. I checked the carburetor float and cleaned the needle valve and seat per another video ... although they were clean. The problem was the fuel bowl O-ring and maybe the small O-ring on the fuel bowl drain screw. Since I have a new carburetor coming in the mail, I used gasket sealant on those O-rings that were not as supple as they should've been and they were getting thinner and becoming a little brittle. After the fix, I put fuel in the tank and the mower started on the first, easy pull. Perfect!

@johnrazor8720 6 лет назад

I enjoy the detailed descriptions of what you are doing and why. Looking forward to how you like the new moving cart setup and a tour of your shop.

@doublewide6 6 лет назад

Coming up soon John.

@truckdevine 4 года назад

Thank you doublewide6. Precisely what i was looking for, gas leaking from carburetor/air filter.

@Serious.5097 Год назад

You are awesome man. Just fixed my practically new lawn mower by taking apart the carburetor and putting it back together. No more leaking - i think the bowl gasket may have slipped. Thanks!

@jeffreygoodson2563 5 лет назад

Thank You doublewide6! You’re a great man. Awesome video. Showed me a lot of stuff that I wasn’t sure about. I hope your finger is doing better. Best Regards, - Jeff

@grotekleum 2 года назад

Talking is good; a running commentary explaining what you are doing is, IMHO, beneficial. I dislike those videos where they don't speak, and shake things at you or point and whirl their finger around the object in question. My neighbour dropped his 'sit-on' for me to look at with just this problem, so the blowing and Q-tip tips will be put into action. Thanks for sharing.

@tnyslt1sault626 5 лет назад

great tutorial. tried on my HRX 476. CHEERS

@darrelljernigan3241 2 года назад

Doublewide 6. Outstanding video, I believe you have answered my question regarding why my air filter housing gets full of fuel. Freaking float. Thank you brotha. Keep up the great technical expertise.👍👍👍👍👍

@jfernandez7366 4 года назад

Thank you for the video. This seems to be the exact problem with my mower. Thanks!

@ronhart4166 6 лет назад

You love the tool cart !! Perfect for the everyday used items :) It seems to help keep your main box cleaner and neater also :)

@doublewide6 6 лет назад

We Shall See. So far so good!

@TomTom-by5sx 5 лет назад

Doublewide6 Repairs Just went through this same issue on my Toro. Didn't have any parts so I got a new carb. for 13.00, checked it out and found the float is the problem. Looked just like the one you had, not quite level. Any way, it runs great, those plastic floats just don't last. Good video, thanks.

@danielfreakdaddyalexander5930 3 года назад

I've gotten bad cheap carbs often enough to avoid them. Even worse, customers often come in with brand new cheap carbs and insist that the problem can't be the carb, because they replaced the original $75 carb with a $10 carb off of ebay. I've gotten lucky before myself, and not so lucky more often.

@trimecm1611 5 лет назад

The enthusiasm is off the chart

@dfields9511 6 лет назад

I have used a Briggs seat in a Tecumseh carb before and it seemed to work in a lev195ea engine/carb Granted it wasn’t the best thing todo but something to try. Good work hope the customer is happy.

@doublewide6 6 лет назад

So far so good.

@danielfreakdaddyalexander5930 3 года назад

The common small rubber seats are the same. Usually red for Briggs and green or white for Tecumseh, at least the originals. There are a couple odd carbs that use a larger size- it's hard to find. But I often get Briggs in with green or white ones and Tecumsehs with red ones. Someone else put them in and they worked for years until they swole from ethanol gas.

@BrucesShop 6 лет назад

Switching tools around messes me up for a few weeks. Thanks for the mention Your new cart will be great.

@queenstownkid 6 лет назад

bruce has the cleanest shop ive seen

@BrucesShop 6 лет назад

Well there are some cleaner but a tile floor is not in the budget.

@doublewide6 6 лет назад

Yup it seems to be a nice addition. Thanks

@cartoonist1975 Год назад

have a pressure washer with the same carb you're working with. nice touch on the dishwasher / brush machine there !

@thomasevans8233 4 года назад

Great video, thanks for sharing, good information and inspiration to organize ones work area.

@MichaelVilesandFamily 4 года назад

Thanks for the video. I think this is my problem. Gonna take my carb off and take a look.

@marshallborder9089 6 лет назад

Good video , thanks

@ozzstars_cars 6 лет назад

Time to mow. Another one fixed! Nice work.

@doublewide6 6 лет назад

Yup it cut very nicely. Thanks.

@bongban. 6 лет назад

good job, thanks you sharing

@nashguy207 6 лет назад

Hey Bob thanks for sharing. Good tips for people with the same problem. I have the previous version (series 1) Tool cart from HF and love it. I keep all my air tools impact sockets and a few other things in it I bought a bigger bax earlier this year and looked at the Husky's and some others I ended up buying the one at harbor freight I felt like they were a better quality box for the money when you shop them and they are on sale they harbor freight tool boxes are hard to beat for the money. Hope the boy is doing great. Have a great weekend. God Bless!!!

@doublewide6 6 лет назад

I was going to get the HF 56 Us General but it was about $700 for bottom and $400 for top on sale Plus tax. I happened to find the husky used for $350 I couldn't pass it up. I am going to make a video soon of this, so you can get all the details. Bobby is doing great. Thank you. Bob

@nashguy207 6 лет назад

I dont Blame that was a great buy for the husky 350.00 used I would of done the same thing in that case. Glad to here Bobby is doing well always goos to see a video from you. Have a great weekend. Bob

@alssmallengines 6 лет назад

Great fix Bob!

@doublewide6 6 лет назад

Thanks!

@knighthawk86855 6 лет назад

Yeah Bruce is super organized, I'm picking up a 10 Draw tool box to get more organized myself tonight...... Lol

@doublewide6 6 лет назад

I like the harbor freight us general 56" box set really nice in person.

@johnhouli3450 Год назад

Thanks Double Wide

@michaelgonzales8807 4 года назад

Good job man!

@chrismedia234 3 года назад

Love the tool cart by the way🔥🔥👍 Thanks a lot, doing a friends favor had the same issue.

@gregorypierce6703 4 года назад

one thing I do when working on a carburetor is after u remove it from the mower take a screwdriver or marker and put a line/mark on bowl below the fuel inlet so in case your bowl gasket happens to be questionable and its midnight you can put bowl back in the same place and still use the carburetor until you can get one.

@Jim-ie6uf 6 лет назад

Super video. Baking soda is great for cleaning the needle seat hole. I’ve use some Amazon chineseum carbs on Briggs with good success, too. Great for corroded carbs. Ice the finger, you’ll be ok. Check the oil .

@ncrdisabled 6 лет назад

Love the t shirt !!!

@tcocheltree1235 Год назад

Now I really like that lift cart, said you make it

@tomharries847 6 лет назад

awesome video and love the q tip idea. one thing though, if your gonna go through the whole hassle of cleaning the carb, surley you should clean the engine and everything where the carb attaches to before re fitting it. its just something i would do my self.

@doublewide6 6 лет назад

Yes, I think I blew it off with air (may not be on film)

@miguellajara8988 3 года назад

Thanks for sharing

@timstoltzfus8408 4 года назад

Very helpful. Thabks for sharing.

@samishaq9998 4 года назад

Good job, I liked you ideas

@kwa6022 5 лет назад

You can punch a small hole in the nail with a paper clip burnt to red hot. The haematoma below the nail can be drained. In good hands, no anaesthesia was required, no sterilisation was needed. Of course, washing of the dirt from nail surface was required. Dressing by a band-aid is sufficient.

@Cyborg9799 Год назад

Thank you. I a m facing the same problem with a Toro personal pace. If I crack it open and have same carb issues that would be great. Funny when you mentioned that you made mistake with tractor I thought you were going to say you broke the tractor!

@Azov374 2 года назад

Great job thanks

@DKSE123 4 года назад

Awesome Video

@kevinoverholtzer3126 4 года назад

wow that tool set makes you look like a full blown Mechanic

@ChrisMichaelsChicago Год назад

Like the repurposed motor for your wire brush saetup! I thought, It might be cool to canablize a chuck from an old drill so one can swap out different Tools. IE: Sanding spindle, buffing wheel etc.

@robertallain8966 6 лет назад

using a heat gun to warm up the plastic to bend the tang on the float really works well . its just like when you take your glass's to get repaired , they put your temples in a heated sand to warm up the plastic and make it more pliable . this process works until the next time it needs to be adjusted . so you really cant get away from this problem until the use something other than plastic . I did this on a 19.5 briggs motor that some one threw away cause it kept flooding out and the motor was carboned up but after fix and sea foam it ran great and started right up .

@doublewide6 6 лет назад

I will have to give the heat a try. I saw Taryl had a video on this.

@watermanone7567 6 лет назад

Nice fix, great video. Did any of the gas get into the oil. I had one hydrolock last week for a similar issue. Thanks for the video's. Wish my shop looked that clean.

@doublewide6 6 лет назад

No, luckily there was no gas in the oil.

@charlescho 5 лет назад

worked for me! except, my float was angled. in fact, I got another float, and that also angled too. I just had to replace the tiny rubber thing.

@prestigelawncare6657 6 лет назад

Good job man, nice shiny end result on the carb too. Hope you don't mind me giving you a tip that always worked for me with customers, when returning the goods clean them before, make it look good. Customers can not always see where or what you did, and probably don't care apart from it works again, but if it's clean then they feel happy to pay the bill. This I did for ten years running my own garage, human behaviour haha.

@REDMAN298 Год назад

I`ve done the drill thing for smashed fingernails with success. Haven`t tried the paperclip method. Unbend the paperclip and heat it red hot with a torch. Then use it to burn through the nail and releive the pressure.

@cbnx82703 6 лет назад

Check the engine oil , it will most likely be contaminated with gas as well, just repaired the exact same model with the same issue... stuck inlet needle...

@rkillian7233 6 лет назад

Great video, helped me a lot, funny guy, hows the nail?

@knighthawk86855 6 лет назад

I had one in yesterday where the rubber seat was knocked loose and wasn't letting the needle seat properly and that was the problem with the one I worked on, I used my drill bit end to seat it all the way down and that fixed it.

@doublewide6 6 лет назад

Must not of been in right at factory. They are seated pretty tight when done correctly.

@teshuvahemmet3036 2 года назад

Thanks 👍

@knighthawk86855 6 лет назад

I'll tell you what, over the years, I have had every kind of socket there is, and I really like the tekton, I have the 1/4" blow molded case set from Amazon, and it has never let me down Tekton tools seem to be worth the price, and that price is cheap, can't go wrong with that.

@doublewide6 6 лет назад

I like tekton and the replacement tools warranty is simple. I have used it already with a ratchet.

@georgetucker336 3 года назад

Easy fix. Thanks

@mptazrider 4 года назад

You are very informative. I like the way you explain things. I wish you were a better camera man.

@unclewiddy 6 лет назад

kool thanks

@markfanny599 5 лет назад

Hey, I really like your tool cart. I know this video is a year old, so I thought by now you would have a good opinion of the setup. Also, is that a Harbor Freight lift? They seem cheap, but a lot of youtubers are using it for lawn mower repairs. Does it work well for you? Is it the 500 lbs model? Thanks, Mark

@LuisRuiz-zk3uz Год назад

Gracias amigo

@wayneynot 5 лет назад

Love your video, I have a gas leak in my carburetor and I would like to buy some parts for it, where would I be able to find the gasket for my carburetor?

@matthewsantandrea9066 3 года назад

Thanks man. I had gas leaking out of the air box of my pressure washer. The needle was stuck.

@joeypleasants2691 6 лет назад

Watch you and Bruce, love his videos since I worked for a Canadian company for 20 years and traveled in Canada love listening to him talk Ah

@doublewide6 6 лет назад

Yup those Canadians are not too bad.

@anthonyharper8161 2 года назад

Organize Chaos , that is clean ! I'm working in my living room for now . Great video. Dude. Next time just replace the carburetor 🤔 Just a idea..

@villain1409 Год назад

The reason i am here,i found a lawnmower filled it with gas primes it & it worked. So was happy with that,then after turning it of the full tank drained with the leak coming from the air? I watched your video,but any info,i would be pleased with? Thank you for your video.

@TheCrittercam001 5 лет назад

You and Bruce both do good thorough work dw6.

@dalewilliford3834 5 лет назад

But maybe you have it mentioned in one of your videos but the lift that you put the lawn more is on and everything did you make that by that need to get one myself

@Bigolpete 5 лет назад

Would it be dangerous using an electric drill near all the gas fumes? I've seen electric drills have a lot of sparks near the bushings.

@petefroud5308 6 лет назад

Nice work Bob . Chrushing your finger is not fun hurts like hell. Cheers Pete.

@c9sus4 5 лет назад

thank you for the video. For anyone that did not what it is the reason, it is the float, watch 10:45

@mikespain8655 6 лет назад

Organized shop pays off in dividends, and keeping it that way is not always easy. I smashed my middle finger with a crowbar and it was about 40% black. Read online and the rule of thumb is if about 1/3 is black, do not drill nail to relieve pressure and remove blood. It took five months and finally part of the black fingernail fell off with new growth underneath. It hurts st first and it is a slow process, but try to be patient. Nice fix on float.

@compound00 5 лет назад

Same thing's happening with my Craftsman 5.3 mower. My dads getting up in age and gets his lawn done now so he gave me his 5.3 craftsman mower and his 32cc craftsman weed eater. Both leaked fuel. I replaced all the gas on the weed eater and it fired right up. The lawnmower however, I filled it with gas. Try to pull start it like 20 times and nothing. Then I noticed the garage started smelling like gas all night. I went to check why the mower smelled of leaking gas and I noticed the deck of the mower was a little wet with gasoline. Looked to see where it was coming from and noticed the filter is wet with gas as well. Would this most likely be the same issue you had on your customers mower??

@redskool8498 6 лет назад

lol bruce calls me MR Kool ... thanks for the vid .. †

@doublewide6 6 лет назад

No problem Mr Kool.

@falconfeathers9454 5 лет назад

Excellent, and one question. My Murrary Briggs 6.5 HP has never had problems. Suddenly, wouldn't start, so first I replaced the Champion spark, new air filter, but this time, the gas flowed through the air filter. I searched a collection of RU-vids (Thank Heavens you exist).Question. At 7:44 you removed the carburetor bolt but you had already removed the entire carburetor. What I watched for was around 15..suddenly the bolt is on the bottom and carburetor back together. Some vids remove the bolt first, before removing the carburetor, and then use thin wires to clean various holes in that bolt which supply the fuel. With some, that was all they did, put the bolt back on and the lawn mower worked perfectly. I didn't see where you cleaned the holes in the bolt.

@grandpamike5336 6 лет назад

Enjoy all of your videos. Great job explaining problem and fix. Keep up producing these videos. Question? Similar problem with my 4 stroke weed wacker, except oil comes out of the carb. I over filled oil and thought it would burn off, but now leaks through carb. I did take some oil out, but still leaks. Will I need a new carb or will rebuilding carb work? Your thoughts please?

@doublewide6 6 лет назад

The problem should not be the carb. Try to get the oil to the right level and run it. It should burn off.

@danielfreakdaddyalexander5930 3 года назад

Once the oil gets to where it doesn't belong, it'll take awhile before it spits it all out. Not a carb problem. Unless otherwise specified, I find that 20w50 works best in those. Did you say Honda? There is now a special oil recommended for them. Valvoline...Ow20? I think. Wrong oil will make a 4 stroke weedeater type engine run funny. 30w foams up in them. Always store them level and upright. Oil gets to the wrong places if you hang them up or turn them over. Makes them hard to start. Then they spit out oil onto the air filter, blocking air intake.

@anniversary4 5 лет назад

Thanks for a great video. I have a Husvarna walk behind with similar engine. It starts first pull cold every time. However once it has run long enough to fill the grass bag it will not restart until it has cooled for 20 minutes or so. You mentioned that the air filter housing on these can warp. Do you think that is what is happening or is there something else I should be looking at?

@danielfreakdaddyalexander5930 3 года назад

If the housing warps, the primer/ artichoke will not work well. Add an extra gasket or two to help it seal. I coat mine in grease, also. Better seal.

@danielfreakdaddyalexander5930 3 года назад

Auto- choke! Lol

@perrys9872 5 лет назад

so your float is also broken when it comes from the overflow from your gas tap?

@misnlinc48 4 года назад

Cuetip was da chit Blood blister, turns black, just drill. Ohh that's so much better. Relieves aaalll that pressure.

@victoryfirst2878 3 года назад

Crazy question for you doublewide6, what can i put on a 12.5HP Briggs intek engine cooling fins to keep leave clipping dust from sticking ??? The leave dust sticks and seems to really insulator making the engine run hot. Also, the engine has such a small air filter roughly 1 and 1/4 square foot of breathing element total. This really makes you change the filter every few hours. Any suggestions to help me out ??? Thanks VF

@joshualittle9298 2 года назад

Helped me find why it leaked

@bobkernahan6340 4 года назад

Great video but not sure how safe it is to use cordless impact so close to gas dripping all over, the brushes make lots of sparks in motor Be safe and thanks

@chim7741 3 года назад

I just ordered a new carburetor kit while watching🤣🤣🤣🤣

@argo5690 3 года назад

I tuned in for a tutorial on fixing a gas leak and got an ad for Harbor Freight tool carts, organization of tools etc.. Might want to tighten up and edit out the non-related stuff..

@Budro4764 5 лет назад

If I'm not mistaken your engine uses a 498260 carb kit....Those kits come with 2 different bowl gaskets and 2 different air box gaskets..... Your EZ start / Auto choke carb uses the thicker bowl gasket and the simple air box gasket... No need for the gasket with the hole in it.... Save that one for a primer bulb style air box and save 4 bux like that for another carb job... Ok now to the nitty gritty........ I don't think your float was bad.... Both floats were out of level the seat was swollen... I am wrong a few times and I might be wrong now..... I have seen those seats go bad tooooo many times.... Ethanol gas will do that all the time ...... But you got it going and it doesn't leak so you got it whipped.......... I use the smaller kit 398188 a lot of times.... That is just the needle and seat kit and it's 5 bux instead of 14 bux for the whole kit.... I am a Briggs dealer so I keep both those kits in stock and plenty of them tooooo... That Etho gas is keeping us in business for sure ............. Plus Tard Mon Ami ~!~! BTW... YES more narration helps a video a lot ..............

@obinnaasuoha7055 5 лет назад

I turned my lown mower to the side and fuel just started leaking out of the air filter. Could it just be because I didn't close the fuel tank before?(the little white know that seems to be some type of valve for the fuel)

@berardia4 6 лет назад

Most likely a swolen seat keeping the needle from closing and holding the float up. Likely because the bowl gasket was swollen also. Something in the fuel contaminated it.

@doublewide6 6 лет назад

Yes, sir you are right on.

@rlmccullough 5 лет назад

Where did you get the mower Lift? I need one

@2pugman 6 лет назад

Drill your fingernail ? So it is Dr. Doublewide !

@doublewide6 6 лет назад

Not quite.

@65csx83 4 года назад

So much for helpers: always turns into the 'when I nod my head 'joke. You were right not to try the left hand drilling; and especially double right not to ask your wife, Lock the drill into a holder; lets you use the good hand to steady the injured one into the drill bit .

@Sean-John 3 года назад

Im having problems with same engine except its got a bit of oil comming out of the air filter even when I've got the cover off... Do you think it's a head gasket?

@timerrington9276 3 месяца назад

Battery power tool..... fuel fumes 🔥

@dpgoodall 5 лет назад

@doublewide6 I have a craftsman pressure washer with a Briggs 7 hp engine. Was leaking fuel. Got the carb and fixed up but can’t get the throttle linkage and spring figured out. Any ideas on how to figure out how it’s supposed to go together? I bought this used and I’m not sure it was set up correctly when I got it. Thanks!

@beenwashedup5754 4 года назад

Before you take apart take pics so you can put back together auto zone sell the small engine repair manual and it might have pics in there

@Budro4764 5 лет назад

When I was working a shrimp boat many moons ago a friend dropped a cable guide on his thumb..... 25 pounds worth of steel ........ His was worse than yours.. He took his Buck 110 knife and drilled the nail to relieve the pressure... The weight of the knife plus a lil hand pressure made a hole to relieve the pain...... Hey man that pressure on your finger is almost as bad as a toothache..... Plus Tard Mon Ami ~!~!