Тёмный

Layens Frame Build, Assembly and Wiring 

Belding Hill Farms
Подписаться 2,6 тыс.
Просмотров 20 тыс.
50% 1

This video will take you through the steps we went through to build 135 layens frames. These frames will be used in the 10 swarm traps (6 frames per swarm trap) that we are building and 3 horizontal hives (20 frames per hive). There is a great deal of work in making these and we took the opinion that building 135 in a production run would be the most efficient way to build them. All our plans have been provided by Dr. Leo Sharashkin of horizontalhive.com for free and are available to everyone on his site.
We have kept bees before, as beginner beekeepers, but we had poor luck in our first year and lost 3 hives, kept in the Langstroth style of hives. We are hopeful that the swarm traps we have built will catch us some bees, that we can try out our layens frames and layens hive or horizontal hive.
We have not trapped bees before, but we have had bees before. We had lost all 3 of our hives the first winter. We are going to try using a horizontal hive this time around (if we are lucky enough to catch some bees) and there will be videos about us building these hives, complete with insulation. We like the concept of the horizontal hives and Dr. Leo Sharashkin's take on keeping bees.
We built a neat little jig for drilling 1200 holes.
Music by:
Dirt Road Traveler by Audionautix audionautix.com
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/dirt-road-traveler
Music promoted by Audio Library • Dirt Road Traveler - A...

Опубликовано:

 

12 апр 2020

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 64   
@markking8991
@markking8991 3 месяца назад
Thanks for the video!
@rameshpram1444
@rameshpram1444 Год назад
Thankyou brother
@beebob1279
@beebob1279 2 года назад
Nice demonstration. I would do the side pieces differently. Run the 2x4 on a jointer (if you have one). Raise the cutter to the desired depth. Run it until it gets to the point where you want it to go out. Then do the other side. Cut it on the table saw to the width you need and then that's it.
@rpeebles
@rpeebles 3 года назад
Since I didn't have a router at the time, I made my sidebars by making a jig for my table saw and used the dado blade. It is similar to a sled except mine is fixed in place. It would work just fine if the jig slides as well. Worked perfect and was safe because the blade stays below the jig and and only the sidebar will fit into the slot. I think the easiest way would be to use a jointer if it will adjust enough to make the side bars.
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Awesome. More than one way to skin a cat! Lol
@beebob1279
@beebob1279 2 года назад
If you have a jointer raise the blade up and run the 2x4 flat ways until you get the top end that you want. Turn it over and do the same thing on the other side. Use the table saw and cut the side pieces to width. Done. no router table needed.
@houstonsheltonbees814
@houstonsheltonbees814 4 года назад
Nothing I hate worse than building frames. But with this style of beehive it's a must. Cool channel and content 👍. I think your doing well. I enjoyed the voiceover verses the shop sounds. I get enough of that lol... will be watching all of your content. How do you plan to seal these hives. Paint stain nothing lol... Thanks again hello from Kentucky mountains USA
@BeldingHillFarms
@BeldingHillFarms 4 года назад
We have painted the hives externally with a latex exterior primer and will most likely just go with two coats of this and the tops will have metal flashing over them. You are the second person to ask, so we will post a quick finished product tour.
@houstonsheltonbees814
@houstonsheltonbees814 4 года назад
@@BeldingHillFarms Thanks I will be watching 👍👍
@citrumpet1
@citrumpet1 4 года назад
Nice videos. I have also built three of these hives and frames. I was wondering if you have any ideas for top feeders? I just took out one frame so the bees could access the top area and put in my feeder from the apimaye hive leaving a little space between the frames so they could get up into it. Do you have any other ideas?
@BeldingHillFarms
@BeldingHillFarms 4 года назад
Go to Dr. Leo’s site, www.horizontalhive.com and go to the store tab and he sells feeders for Layens hives
@mauriceherbstritt5336
@mauriceherbstritt5336 3 года назад
Horizontal hive plans.
@BeldingHillFarms
@BeldingHillFarms 3 года назад
They can be found free on Dr. Leo’s website. Www.horizontalhive.com
@91932net
@91932net 3 месяца назад
Hi! Great video! I love ur drilling jig…would u mind sharing?
@terry2346
@terry2346 4 года назад
Putting in that wire it might help to ream that rough end slightly with a bigger nail to keep it from catching on you. You could even get fancy and mount that nail into a small handle to make it easier. Anything to make it less tedious! :)
@BeldingHillFarms
@BeldingHillFarms 4 года назад
I agree, anything to make it less tedious is better. Thanks
@rpeebles
@rpeebles 3 года назад
I found that it was easiest to put 1 on the nail and hammer the nail and grommet in place. Then push the nail up from the bottom, lift it out, and go to the next. This is far easier on my fingers because pushing those little things into the wood wear your hands out. If there is a way to SHOOT those grommets into the holes that would be best! :)
@BeldingHillFarms
@BeldingHillFarms 3 года назад
I did the same
@terry2346
@terry2346 4 года назад
Just so you know Bee Boy Bill has a nice setup with the table saw and a jig that I used and it seemed to go pretty nicely.
@BeldingHillFarms
@BeldingHillFarms 4 года назад
I’ll have to check that out, thanks
@joewamsley8004
@joewamsley8004 3 года назад
Turns out the foundations are undesirable for bees because sometimes they will make a hole in the frame to let air through but if there is a foundation there they cannot. I just learned that after installing a new box with foundations, I think from the same guy you are building your boxes off of.
@BeldingHillFarms
@BeldingHillFarms 3 года назад
I saw that too
@jerrymcmahan2855
@jerrymcmahan2855 2 года назад
Was that a staple gun or small nail gun and what size did you use
@BeldingHillFarms
@BeldingHillFarms 2 года назад
It was a staple gun, but I can’t remember the size. Thinking 18 gauge 1” long
@theGhostPatRiot
@theGhostPatRiot 2 года назад
How long did it take you to just cut and build the 135 frames (not counting the wiring)?
@BeldingHillFarms
@BeldingHillFarms 2 года назад
I can’t remember because I did it 2-3 hours at a time, but I believe it was about 10-12 hours. Maybe less. Just cut all of the pieces in mass production and absolutely build the frame jig (separate video on our channel). Also, if you need the information about the jig I used to drill the holes in the frames, let me know.
@scottdc2105
@scottdc2105 3 года назад
Thanks for the detailed video, ive been planning on building a layens style hive box, do you see any issue on wiring the frames horizontally from side to side rather than from top to bottom? If you grove the top bar you can install a wood strip and wax it to start the bees comb off straight and the wire wont be in the way.
@BeldingHillFarms
@BeldingHillFarms 3 года назад
I think that would work, but you might have to stiffen the joints of the frames.
@elvisestevez5816
@elvisestevez5816 3 года назад
Great job! Quick question: Dr. Leo's hives come with edge protectors. I've already "sealed painted" it 2x and ave allowed it to completely dry; however, as I'm putting in the first edge protector, I'm noticing the wood crack. In drilling screws into other items such as the lid or gate discs, I did not notice any wood cracking. Any advice? Proceed without worry or stop adding on the edge protector?
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Thanks for watching and if you are getting cracking, you can simply pre-drill the holes with an undersized drill bit before putting in the screws. That will relieve the pressure that is most likely causing the splitting. Just play with the drill size until you are happy, but don’t go more than half the diameter of your screws or they won’t have enough holding power.
@bradgoliphant
@bradgoliphant 3 года назад
Could you please let me know where you bought those tiny metal grommets? Also, it is true that the queen won't lay on wire when it's treaded on the frames side to side vs top to bottom?
@BeldingHillFarms
@BeldingHillFarms 3 года назад
I got them from Dancing Bee Bee Supplies from Ontario. I never heard of the queen not laying on horizontal wired frames.
@bradgoliphant
@bradgoliphant 3 года назад
Hello, I have Langstroth Deep hives, but really like this deeper frame. Essentially I want to attempt to connect a shallow and a deep frame together and in shallow and deep box? Do you think this could work?
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Honestly I'm not sure. I have seen where people have made Layens frames that hold deep and shallow frames sepatately, but not sure of combining. There are also designs on Dr. Leo's site for a horizontal hive built specifically to hold deep Langstoth frames. Check out his site at www.horizontalhive.com
@billymarkwell1105
@billymarkwell1105 2 года назад
Would you please tell me what size grommets those are and where did you get them.......
@BeldingHillFarms
@BeldingHillFarms 2 года назад
I’m honestly not sure of the size, but I got them at Dancing Bee Supplies in Ontario, Canada
@billymarkwell1105
@billymarkwell1105 2 года назад
@@BeldingHillFarms thanks
@BeldingHillFarms
@BeldingHillFarms 2 года назад
Very welcome
@danieldeskins
@danieldeskins 3 года назад
Great video Do you have a video on how to harvest the honey from the larger frames do you have custom gear?
@BeldingHillFarms
@BeldingHillFarms 2 года назад
Not yet!
@kayandtylorsbees4631
@kayandtylorsbees4631 3 года назад
I would love to see your plans or dimensions for the drill jig. I'm about to have to build a little more than 100 to 160 of these frames and that would be much better than the "jig" Dr. Leo provides with his plans. Thank you!
@BeldingHillFarms
@BeldingHillFarms 3 года назад
You are the second person that asked. I am happy to share. Send a message to our Belding Hill Farms Facebook page and I will send you pics
@donnamarie9593
@donnamarie9593 3 года назад
@@BeldingHillFarms hope you don't mind, just did the same! we're in the middle of building our 3 Dr Leo hives from his plans and haven't started on the frames....any help would be most appreciated, another brand new beekeeper here
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Watch my other videos on building frames and the jig and if you want details of my drilling jig, just email us.
@donnamarie9593
@donnamarie9593 3 года назад
@@BeldingHillFarms thank you! yes, just viewed it "after" I emailed you :-) appreciate all you do to share with other newbie beekeepers... or in this case, wannabe beekeepers... in the middle of building our boxes.
@dermotjones
@dermotjones 3 года назад
very nice video... could you share your jig plans?
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Yes I certainly will. Send me an email (beldinghillfarms@gmail.com) or a message to our Facebook page
@keig6161
@keig6161 3 года назад
Awesome thank you so much for this video. I planned on building my own frames. Did you think you saved a lot of money as opposed to buying them?
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Truthfully, likely not, but I love the satisfaction that comes from doing things all with your own two hands
@wayneolson7711
@wayneolson7711 3 года назад
Can you tell me where you were able to pick up these small grommets? and what they are made from? Thx
@BeldingHillFarms
@BeldingHillFarms 3 года назад
I got them from a bee supply store and they are made of brass.
@rpeebles
@rpeebles 3 года назад
www.amazon.com/Walfront-1000pcs-Beehive-Threading-Beekeeping/dp/B07FDCLGR9/ref=asc_df_B07FDCLGR9/?tag=hyprod-20&linkCode=df0&hvadid=309858491514&hvpos&hvnetw=g&hvrand=1162656857188050039&hvpone&hvptwo&hvqmt&hvdev=c&hvdvcmdl&hvlocint&hvlocphy=9028372&hvtargid=pla-612808683257&psc=1
@sfcmmacro
@sfcmmacro Год назад
Where did you get the grommets and what size are they?
@ledfootdude
@ledfootdude Год назад
He answered it in previous comments
@sfcmmacro
@sfcmmacro Год назад
@@ledfootdude thanks for the helpful reply.
@duncanjames914
@duncanjames914 3 года назад
Can you spin those frames in a conventional extractor?
@BeldingHillFarms
@BeldingHillFarms 3 года назад
No, but I just figure when I get there, I will build something to do it. That's udually how I do things. Lol. There are commercial spinners for Layens frames, but the normal Langstroth spinners won't work
@duncanjames914
@duncanjames914 3 года назад
@@BeldingHillFarms Good to know. - thx.
@rpeebles
@rpeebles 3 года назад
They make extractors that take both langstroph and layens frames...just not real common in the US.
@BeldingHillFarms
@BeldingHillFarms 3 года назад
Agreed
@abdennournahal6852
@abdennournahal6852 3 года назад
What are the dimensions of the frame
@bradgoliphant
@bradgoliphant 3 года назад
Hello again my friend. Would you bee willing to build ten Layen Frames for me. They are modified being 19" wide x 15.5" long. I need to hire someone. I'm happy to pay you for everything> Let m eknow
@user-kn2kq4uv5y
@user-kn2kq4uv5y Год назад
а какойразмер вашей рамки?
Далее
Episode #62Top Bar Beekeeper Builds Layens Hive
11:43
Просмотров 2,5 тыс.
Прятки #nyanmp3
00:25
Просмотров 187 тыс.
How to Make Frame Parts for Layens Horizontal Hive
10:24
Building an Insulated Layens Hive Part 1
16:02
Просмотров 12 тыс.
🔵Long Hive Beekeeping Episode 1.
15:59
Просмотров 110 тыс.
Layens Hive - My two Modifications
10:22
Просмотров 32 тыс.
Building Simpler Foundationless Layens Frames
4:16
Просмотров 2 тыс.
Cutting Hive Frames.  Part I.  End Bars
32:12
Просмотров 29 тыс.
Прятки #nyanmp3
00:25
Просмотров 187 тыс.