LED HEADLIGHT INSTALL ON FORD FUSION: How to install led headlights on a 2014 Ford Fusion. 

LINK TO HEADLIGHTS 👇🏻 👇🏻👇🏻👇🏻👇🏻👇🏻👇🏻 auxito.com/products/ford-fusion-led-bulbs-2013-2017?ref=oqq49zdb4x&variant=41029409210520 USE CODE - “AUTOHEADZ” FOR 15% OFF!

“You should be able to do this in about an hour.” Video starts at sunrise and ends in the dark. Thank you for this, I’ve had to replace mine twice, it’s such a pain. There are videos saying there’s an easy way where you don’t have to take the bumper off, it’s not easier, trying to twist the light into place is only possible if you have tiny hands.

Holy crap.... you're a better man than me and you must really like your brother-in-law. My daughter has the exact same car and was at Midas....told me it was $120. I said , leave we'll do it ! Mostly labor... After watching you. She's going right back tomorrow !! I am not changing Jack ! Great job with the video !!! I'm glad I watched....but no way ! ☮️

Thanks for the instructions. I successfully installed in my 2015 fusion. One thing to do when installing low beams is to also replace the daytime running lamps with white LED lights. Else, just the DRL’s will be yellow and LED’s white. I think they are 925’s and are located next to high beams .

These bulbs are very well made thats for sure they look quality

Thank you from Dublin Ireland, what a nicely paced, fully informative tutorial, I wish I'd found this video yesterday,

Thank you for the helpful video! The lights that came with my fusion were atrociously dim, and thank goodness you made this video, spent about 1: 30 with my dad and we were able to switch em out for brighter ones! Cheers!

Hey man thanks for the video! Used your link and got some. I had some silver star ultras I was going to put in before a big road trip. But I wasn’t sure if I should use halogens again. Thanks for the easy steps!

THANK YOU SO MUCH U SAVED ME TIME AND MONEY

Here here here and here 🤣 Great video man!

Great video, well done.

Great video

Thank you!

Thank you!!!!

Good job

hi ive puchased the h7 for my ford fusion directly from china but im not sure they come with adapters ,,so my quick question is what kind of adapters do i need for my 2015 ford fusion and how do they look like for those h7 bulbs many thanks

Literally takes me less than 10 minutes to get the bumper off and the headlights out. But i just drop the bumper down from the front end, I dont take it completely off the car.

Only ford Engineers would do such a bad design ,To replace the headlight bulb you need to remove the bumper , imagine you are on the road and need to replace the bulb

why you dont show how to change the high beams

Do you ever have your headlight come on whatever you have leds low beam tell it happens too 2016 ford fusion

I have a 2017 SE and you don’t need to remove the bumper to change the bulbs. For me I just want to change the whole headlights

great video, just drove my girlfriends fusion and realized the headlights are horrendous, going to add these in for her using this video! are these the bulbs that would be the blinkers tho? if so, id like to get some switchbacks in case you have any you can recommend? im thinking of doing all the lights in the front for her, low/high and fogs too (not sure if it does have fogs tho). would greatly appreciate any links or anything you may have! and again, great video!

I thought you’d like to see this video. Ford fusion headlightbulb replacement 2013-2020 on the “The Driver Mod” channel. No bumper removal literally 6-8 mins a light. Hope this helps your brother faster in the future.

Did you change the high beams also plus other lights in the headlamps? Like turn signals and so on

Great design Ford…

Thanks for posting. Any idea about the lifespan of those LED bulbs? I'm due to replace my factory bulbs and am considering an upgrade. However, since changing the bulbs is more complicated than the invasion of Normandy, I'm not looking to do it again for a long time. Will the LED bulbs last? Any idea if they are DOT legal? Also, are they so bright that other motorists will be flashing me thinking my high beams are on?

Qué modelo de lámpara leds lleva? Para las luches y los camineros abajo? Gracias

One thing not mentioned in the video is that the length of the new bulbs is greater than the originals. So you cannot put the bulbs in the socket in the same place as the original on the driver side. I tried to do that, but I realized that 1) it would not fit because it would hit the rim of the dust cap hole and 2) the leds would not be vertical. So, I had to install it with the stem facing downward. Actually, that is correct for the driver side. I tried to install the same way on the passenger side, but now the bulb would hit the rim of the hole since the alignment is different on the passenger side. I decided to install it with the stem of the bulb facing towards the driver side of the vehicle. This puts the leds at 120 degrees off vertical. It's not ideal. Elsewhere, I saw instructions that the orientation of the led can be changed on the bulb with a small screwdriver. Once I recover from this installation, I will pull the passenger bulb again and try to fix the led vertical alignment.

I recieved these h7 bukbs but i dont know if they are with adapter or not can You send apic or link how those adapter look like ...would be helpful many THKS

Hey I just installed these on my 14 fusion but I wasn’t aware that the projector lens in the housing isn’t really compatible with leds since it creates a small shadow in two spots (since led lights go outwards instead of forward). Did you have this problem or no ?

This will be long , apologies. But yes you CAN change your bulbs without taking bumper off, you can take the headlight mount brackets out. The larger led lights all fit different depending which model too It is VERY tight, potentially extremely frustrating and you’ll beat up your hands but Also couple screws (10mm bolt under the hood stops that you pull off) that are extremely easy to drop into engine bay then your gonna be in a worse spot. After going through all this on couple fusions , I started taking the bumper PARTLY off, Basically remove all the screws and clips along the front / fender liners. Pop bumper off slightly, disconnect some connections, and then there is two bolts under each headlight, removing those will allow you to slide headlights completely out after unplugging . Take off majority of headlight mount too ofc. Sounds like a lot but it took me less time overall due to ease of changing all lights at once when it’s out. The amount of time it CAN take using the other method along with higher chance damaging something too forcing stuff in small space. Changing the 194 led running lights at same time recommended as well. Or they will be on and mixing with the light from leds. If that bothers you anyways.

Hey, I bought Auxito's also for my 16' Ford Fusion but they have ballasts on them. Do I put the ballasts inside the dust cap too or is there wa spot I can run the wire outside the dust cap? What about the fans on the LED's? Are they okay inside the dust cap with the fans running on the back of the bulbs inside with the dust cap on?

Seems like Ford kept screwing around with the front of the engine bay on the early 2nd Gen Fusions. I had to change the low beam bulbs on my 15 Titanium about a year or so ago because the oem halogens finally crapped out. Not a difficult task just frikkin tedious. If I recall, I only had to remove the top fasteners and the wheel well fasteners to pull the top of the bumper cover out just enough to get the light housings out. I believe Ford slightly modified the forward upper brace on the 16 and up to allow just enough room to fit your hands in there to change the bulbs without all the dumb shit. I think they purposely shoe-horned the damn motor and all the components into the engine bay to make things harder for DIY'ers to work on hoping to force a visit to the stealership service dept.

thankyou for this, im now thinking why on earth did I buy a Mk5 Fusion / Mondeo ( UK ) , such a job just to change a few bulbs.

I’m new to working on cars and I looked it up but I couldn’t get a good answer online, if I change out my halogen bulb for my low beam but not high beam will my high beam still have that yellow look to it. And if so is there anything I can get to make it to where they’re both led?

Is the installation the same on a 2020 ford fusion

I have an issue of flickering when turning on the blinker. Does anyone else have the same problem?

Not sure what year you are working on. Mine is a 2019. Hate to break it to you but you DO NOT HAVE TO TAKE THE FRONT END OFF!!!! I replaced mine, high and low beam just using my hands. Takes some time but it can be done.

Did you need a flicker module?

I bought these headlights , I have a 2014 ford fusion se...they don't fit

dope ass fucking video thanks alot

Great, next thing it would require removing the engine to change some oil, I own a 2015 titanium and this shit is pissing me off just to replace some damn bulbs and I have to remove the whole bumper which would definitely make it loose.

i will say… if you’re changing high beams on the 2015 Model, do not get the H7s with the heat sink at the end. Almost impossible to fit because the light housing is aligned oddly. Find an h7 that’s 1-to-1 with the original bulb.

You don't have remove the front bumper to put headlights bulbs in. I changed mind out to led in 30min. It's other videos showing how to. My family owns a collision shop

So you’d have to pay them more. But there’s a way faster way faster way. You don’t have to remove the bumper

You can access from the top

I love my Milwaukee colorless ratchet. Break em loose and zip em out

Maybe spin the ratchet like a wrench instead of ratcheting when it’s unnecessary to save your arms.

3 minutes into this video.... OH HELL NO!

You don't have to take the bumper off, lol.

These cars original headlights suck, especially if your windows are tinted. I need to upgrade my lights soon, don't wanna kill anyone lol

Ridiculous to change headlight bulbs

Ford should be ashamed of themselves for making it difficult to get to the bulbs.