Mag-lite Repair fix exploded corroded batteries 

Will try, I think it removes anodizing?

And also soak the body overnight in vinegar. And to help it not to happen again I put a little bit of this stuff called ‘corrosion killer’ its made by Killer RC and it’s safe on batteries and electrical circuit boards, rc receivers, servos etc. I use the stuff in R.C. It works a treat. I did exactly what you sed when my maglite batteries leaked, then followed it on with my procedure

I actually showed you how I fixed my mag-lite

@@fintechrepairshop No, you didn't!! Why do you think you have more dislikes than likes???????

It's not the Maglite, it's the shitty made batteries.

@@Tom-qx5nl exactly I found the problem with my mag lights to be the Duracell batteries, supposedly they will warranty that if there's Duracell's in there too. EDIT: apparently they change this policy sometime in the 10 years since I looked at the website, they've also started including energizers in their packaging.

I done the same. Pour some vinegar into it. This eats the corrosion.

YOU should have made this video.

Thanks for the warning. I won't waste my time. Thumb down.

Yeah, I came here because of duracell (date code 12/2022) leaking and ruining my maglite. (among other things) I'm never buying duracell again

@@tonykara they destroyed many Maglite we've had and a few other things

How do you remove the circular retaining clip

B.R. Field I can remove the retaining clip on a maglite where the cells aren’t blown and the flash switch/bulb housing is already removed, but on the Maglite where the cells have corroded I can not get the clip out as the switch unit is pushed up against it! Any ideas?

@@boarderfalife Hello, unscrew and remove top of flashlight, unscrew and remove the blub. (Look inside and you will see the retaining ring, but don't remove yet). Then remove the rubber cover over the switch, then use a 2MM allen key to loosen the switch assembly retaining screw. NOW remove the retaining ring (with a flat blade screwdriver) and then switch assembly (push in switch) from the top .

@@simonking6247 Hello, unscrew and remove top of flashlight, unscrew and remove the blub. (Look inside and you will see the retaining ring, but don't remove yet). Then remove the rubber cover over the switch, then use a 2MM allen key to loosen the switch assembly retaining screw. NOW remove the retaining ring (with a flat blade screwdriver) and then switch assembly (push in switch) from the top .

B.R. Field yeap, it’s the last bit with a flat blades screwdriver I’m struggling with. Will persevere, thanks.

M oo go pool oo pop okmj

In poof o

Allen screw holds the switch into position within the body of the maglite. LED version don't use Allen but Torx T7 screw.

@@lardy70s Tried a T7 but I don’t think the neck was long enough to engage the screw.

Ebay amazon etc etc.

From another video the size appears to be 2mm

@@geneevans4148 I tried 2mm and it just seems to spin in mine.

Just found why 2mm isn't working for me. The newer ones use a special T8 Torx wrench. Watch this video for more info. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MKydwYD98J4.html

I can confirm 2 mm Allen key for the 6D lamp I managed to save. Comment section says newer models seem to use a T8 Torx or a T7 Torx screw. Good luck with yours…

I would remove the reflector at the top of the maglite and remove the bulb. Next you need to remove the rubber button and you'll see the switch which has a small hole in it. Use a very small allen key that fits into the hole and you'll feel it locate within the allen screw. Loosen it off. Looking down the top you'll see the switch which is held by a type of plastic circlip. This is very difficult to remove as your batteries are seized and is holding the switch up. You need to concentrate on removing the end cap. Apply a little heat from a hair dryer and using some mole grips/vice grips try loosening the cap. You have to remove this. If you have removed the cap, you should see the bottom of the seized battery. Pour some vinegar into the bottom of the maglite and leave over night preferably in an upright position. Put some more vinegar in and leave for an hour or so. Strike the bottom of the Maglite square on on a good piece of WOOD!. Nothing else!. Keep doing this whilst adding a little vinegar. The vinegar eats into the corrosion. You can also use some penetrating spray to lubricate to assist. If you manage to remove the first battery, continue with the rest. If you get them all out, the switch should come out also. Pour some more vinegar into the tube. Once you're satisfied, wash the maglite with some washing up liquid and hot water. Dry thoroughly. Spray some contact cleaner on the switch and make sure it's clean. Refit the switch and tighten up the Allen screw. Fit the bulb and the reflector. Add new batteries. Let me know how you got on?.

Im having the same cap problem, did this work?

Heart beats you will never get back.

Funny, don't want to upset the youtube overloads.