Magnetic Switch Motor

Подписаться 67 тыс.

Просмотров 85 тыс.

50% 1

With the world’s current volatility and market instability I highly recommend you get some storable food for yourself and your family. It never hurts to be prepared for an emergency before it comes. I get mine from the largest and most trusted source in the market. Click the link below and take a look for yourself.
mypatriotsuppl...
This video contains information on how my magnetic switch motor works and how it’s constructed.
Some of the specifics are as follows:
I used four N52 neodymium magnets in this video. They are .05 x 1 inch in size. I stacked them to form two 1 x 1-inch cylinders.
The 2 metal bars I used in the rotor are 6 x 1 inch.
The shielding material is from CO-NETIC. There are three sheets, which are each 8 x 5 inches. The holes are 1-inch diameter, with a 3-inch space between them, centered in the metal sheets.
This design would have a much better chance of working consistently with square magnets with at least 400 lbs of magnetic hold force, low friction bearings, and a leverage bar triggering the switching of the shielding slider.
The Key to building a Magnetic Motor:
• The Key to building a ...

Опубликовано:

18 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 439

@planesmart75001 Год назад

I have been working on this for over 50 years, ever since I was in college. I have even made the curved magnets in Howard Johnson's model. I have tried a lot of designs. Right now I am in my 70's and want to give you what I have found. The best I have found is the simplest. We are very close to each other. Now to demonstrate my closest model I can describe it simply. Take a model train. I made mine with my 3d printer. I wanted to make sure I had no eddy currents. I used fidget spinner bearings too. :-) Place a long magnet cross-ways on the train car. The magnet is orientated north and south on the largest flat sides. It is placed at a 45 degree angle. Then you have another flat magnet placed on the bottom table. The table magnet will attract the car magnet till it is very close, then the resistance is a very small but strong place. Once past the resistance, the table magnet pushes very hard. You get a pull, then a push. Now, I was using a combination of co-netics shielding, and a torrent coil to reduce resistance. The torrent coil helped short out the magnet and the co-netics helped block the force fields. The torrent coil is of the lowest power I can use, and is turned on very quickly. I want to get all the push I can get from the magnets. I am having a little issue with the spacing. I want to have the magnets which pass each other as close as possible, but the torrent coil was getting in the way. I had ran some math and the best angle is 45 degrees. I hit myself in the forehead, because that was obvious. No need for the math. I was running all sorts of math configurations 30 years ago when visual basic first came out. I was a main frame programmer for IBM. I got a partner who lives in Melbourne Australia. We have been swapping information for the last 30 years. I was working on my latest model when my 3d printer broke. The filament pushed the guide into the heating element. I was using 4 inch by 1 inch neo magnets. Just got to be careful, they can snap your fingers. The co-netics get close, so the torrent coil should push it over the hump. The power produced should way more than be enough to turn a generator and run the torrent coil. Now, I have not converted this to circular motion yet. Last time I did, the angles were off, and I had eddy current issues. This is why I wanted to get a couple working first, then go for the circular motion. Right now, I need to get my 3d printer working, and find the proper torrent coil with the current to accomplish what the math tells me will occur. I have been told this is perpetual motion, but I do not agree. I think this is just a way to use the magnets properly. Now I did find one thing, the constant pushing and pulling on the magnets wore them out. (lost their magnetism) I just do not know how fast. I still think this could work for a while to be commercial. But aren't we all optimists. :-) Just be careful, these magnets bite fingers.

@Motionmagnetics Год назад

Have you shot any footage of what you are describing here? I would love to see the physical results of that track.

@transformyou7495 3 года назад

Tysm your videos are really the only videos that I trust the info. I'm also building my own magnetic system, but I think I will be sad when it works because this is my only passion in life. But because of you I understand how the system work that I made and I could solve alot of the problems. The best advice I think was to start with a linear assembly before you make a rotary system. I watch your videos every day, I know there are not that many to watch but the information brings inspiration. Tysm

@joshuanorris9785 3 года назад

how is your experiment going good sir? Id love to hear feedback!

@ANT-jm4qx 3 года назад

This dude really believes he doesn't need to obey the laws of physics haha

@harizhaqim3906 2 года назад

At least he tried

@ashercorbett8089 20 дней назад

*Issac Newton posting wanted posters for breaking the law

@FiveTrackTape 4 года назад

Brilliant. Thank you sir.

@Motionmagnetics 4 года назад

Thank you.

@RAFAEL_ANRIAL 3 года назад

@@Motionmagnetics Hello! A friend of mine who had a free energy generator showed me a diagram of how to make a magnetic switch where the switching cost will be 1 W, and the gravity will be 200 kg, which must be accumulated in the flywheel! it all works, switching by electrical impulse

@kongdmg Год назад

been a fan of you channel for a while.. def good to have an optimist mindset in new idea or old concepts.. ive constructed a concept that remove all issues (known) so far.. needing more resources to build it without the extra questions and more professionalism..

@hansbraun2726 Год назад

I love your videos and I appreciate all you do very much. I admire your creativeness and your ability to apply your ideas into working models. Thank you for sharing all you do with the world. The work required to "switch on" the shielding will always exceed the work done by the field moving the magnets. The strength of the field drops inverse squared with distance. So the distance required to fit adequate shielding to block the field will diminish the force to less than the force required to move the shield into position. and leverage does not change the work done. It just allows for a smaller force over a greater distance or for a longer time. I was obsessed with this idea for quite some time but throughout all my experiments, eventually came to the conclusion that it wasn't able to overcome the laws of conservation.

@planesmart75001 3 года назад

Hi, I love what you have done. This is a way I have not ever considered because I had trouble with the co-netics. I have been interested with magnetics since high school, which was a while ago. A long while ago. I have been playing with these designs for a lot of years. A lot of years. Before 3d printers I was making the frames in plexiglass. Before that I tried Aluminum. This was before I experienced the eddy currents. I was able to make a motor which was more of a clutch. It had 10 lbs of resistance one way with 1/2 lbs of resistance the other. I am very excited on my current design (but I have been very excited on the last 50 too) . In college I found no one knew too much about magnetism. So I experimented. I have smashed fingers many times, and then in a Popular Mechanics (I think) Howard Johnson patented a motor. My main problem is that my profession was computers. Once my son was playing with some less powerful magnets and yes placed these on a laptop. My desk has 5 monitors with 7 computers. They are not all PC's. I had even worked with a professor in Ukraine, and I had some special curved magnets made for me. I was going to try and make the motor Howard Johnson drawn up. These are in the crescent moon shape. I have never worked with these, mainly because of all the computers. Now where you are using fidget spinners and 3d the carriages, I used the LGB (Large Trains) to experiment. I still never got to use the curved magnets. These curved magnets are about 10 inches by 4 inches. I think I got 5 of these. I would give these to you if you are interested. You have been the first magnetics person who was not touched in the head. I include myself as touched in the head. I have always known since I made my "clutch" it has a difference of 9 1/2 pounds. If I could have shaved that 1/2 lbs off, then I would have had a true magnet motor. I am almost 70 years old, I have a degree in Quantum Physics. (I failed English many times). This all said, would you be interested in having these magnets for free. They cost a bundle, but I do not know how much longer I am going to be around, and you seem to be the perfect to give these to. Just keep posting these fun videos. I have never posted anything, because I never got anything working as a motor. Always close, but quit mostly because I did not need to loose any more computers. I have been told many times this is perpetual motion, I never believed it. I just believe it was a force we never explored to find how to control its powers. Let me know if you are interested. Thanks

@joshuanorris9785 3 года назад

any updates on your design sir? I'd love to hear discovery!

@JustChillingOut Год назад

🦋 I as well have gotten up in years, so time is no longer on my side either. I explored the idea of using curved magnetic fields, but simply switched that out for a curved magnetic 🧲 runway plate that provided equal if not better results. I then realized that no matter the shape of the magnet, that as long as Newton’s third law of motion was always in play, a magnetic motor wasn’t possible. Then I remembered a simple demonstration in Highschool Science where the lid of a tin can would shun a magnetic field. However, simply shunning the field was exactly half of the equation to overcoming Newton’s third law of motion. The second half of the equation was a light bulb moment. Since the attraction from one magnet to another magnet is far greater than that of the attraction of a magnet to steel, capitalizing on the difference between these two attractions would become the magic bullet for overcoming Newton’s third law of motion to creating continuous motion for a magnetic motor. Ten minutes later, I had created a simple magnetic shielding process that shunned 99% of the magnetic field. While at the exact same time a portion of that magnetic field is left wide open where I used my shielding process to focus the field like that of the barrel of a gun. Now I had stator that would easily overcome Newton’s third law of motion that worked prefect. No Longer was the equal and opposite force an issue any longer. I know had an imbalance system. Lastly, I came to realize by putting a layer of paper or art board between each thin layer of metal shielding dramatically increase the performance. Soon afterwards I publish my findings on RU-vid revealing that you can indeed overcome Newton’s third law of motion. In about two months my video had received over ten million views. That’s when RU-vid took the video down, saying that my video violated RU-vid’s community guideline. Figuring this was just some simple mistake I then posted my latest new findings in a new video. In just two weeks, RU-vid also took that video down stating it was in violation of community guidelines. Now I knew this was no accident rather I was being targeted. Just three days later I tried to post a new video to my channel only to discover RU-vid had taken down the entire channel. So I started a second channel. This time trying to be more stealthy about what and how I made my videos. That still did not help. Within a month that channel as well was taken down by RU-vid. If I had not known before, I knew now that my research was being targeted in the name of suppression of information. Since then I have avoided putting up any such video that proves a magnetic motor is indeed a reality. Rather I reposted all the old videos that never showed anything working, only videos that showed the viewer what you need to do to get it to work. RU-vid never took down that third channel of mine. At least not yet anyway. I also published a video called, magnetic shielding the holy grail. Soon after that video went live somebody else made a video trying to make me look like a fool for my claim. The way they demonstrated the magnetic shielding technique not working was not the same technique shown in my video. Obviously this was an attempt at disinformation, to lead people away from my solution to overcoming Newton’s third law of motion. Sometime later I found a couple of other channels who successfully replicate my findings. Why motion Magnetics here has never bothered to implement some or all my research into his is mind-boggling, as he has watched my videos. Had he done so, he would now have a working magnetic motor, rather than giving up and walking away from his RU-vid channel. His magnetic switch has a flaw in it which is easy to see. At least for me anyway. The shielding that he is using also has a magnetic attraction which creates friction. Where as my system is not only friction free, but there are no moving parts other than the armature. Motion Magnetics armature switching system is very limited because it’s very mechanical and makes a horrific amount of noise and extreme vibration before it would ever obtain any real speed. Where is my set up is 100% quiet, with zero vibration. No time to proof read, so I hope all of this makes sense to the reader. Hope you’re still around and doing well during this plandemic.

@josephmaza3492 Год назад

Hey man can you post your work on you tube or any other platform that you may have am very interested in what you said in your message

@trinkladd Год назад

@@JustChillingOut sir. Would you share your videos with me. I will share my email. Thank you. IhAre that your work fell on deaf ears. Any advance I would make in your discovery. I would always give you credit. So that your discovery may live on.

@JamesRoneyStators Год назад

🧲 If I may… replacing the shielding plate with the two holes in it with a cut sheet to size of a piece of PVC, would dramatically reduce the Coggin effect you are experiencing. Simply replace the location of those two holes with button magnets of the same size, making sure they are in repulsion mode. Rather than time the movement of the two staters to get out of the way just as the armature magnet is leaving, you would do the opposite. Now you would have each stator magnet come into position just as each armature magnet was 56% to 66% past the center of the stator magnet. Since we would now be working in repulsion mode, this will cause a huge forward motion kick to the armature magnets. In retrospect, your design here will cause an enormous amount of vibration. Anytime we create something that has to start and then come to a complete stop, and then reverse direction, only to repeat this process over and again always leads to vibration. Whereas continuous motion in one direction is what is truly needed. My one way stators are basically a passive magnetic switch that Illuminates the need for Mechanical switches. Just so you know, this challenge of solely using magnets has already been solved. At this stage my goal is to provide a design that generates immense torque. I see you messaged me , and I have yet to catch up on everything, but I have been away battling health issues on the home front with the wife, along with Christmas. Good to know you made it through the plandemic. Turns out the cure for it was super simple to the tune of 35,000 mg of vitamin C. Medically proven to work 98% of the time except on those who are too far gone which is the last 2%. This simple solution that is now being used throughout the world is still banned aon most major platforms to talk about otherwise you’ll get flagged or possibly lose your account especially if you use the word cure in the same sentence.

@Motionmagnetics Год назад

Thanks for the input. Always good to hear your thoughts and suggestions.

@VenturaIT Год назад

@@Motionmagnetics I must not get it, and I haven't studied your design, just watched the video quickly... but why are you using magnetically effected shielding material (steel) instead of aluminum or another non-magnetic metal to shield it? The energy used to move the shield over the magnets seems like it would be a drain on the system? I'll have to watch the video many more times. You could also make the stationary magnets electro-magnets and have them computer switched, I'm sure you know this. I think the energy to magnetize them could be powered by the motion created?

@VenturaIT Год назад

@@Motionmagnetics Today it can be done with arduino or rasbery pi. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-J2bPDDWqSvM.html

@VenturaIT Год назад

Yep, someone doing it with arduino: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WkcVtNjKY7k.html

@VenturaIT Год назад

@@Motionmagnetics ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7xYdaipXXwU.html this kid did it, he says that the sticky point is the just the last 2 magnets... so if those were either removable (like in your design covered with a shield) or just able to be turned off by a computer, maybe that would work? i can't see that the unsticking electromagnet takes more energy than is produced through the rest of the turn, but I don't know the values... maybe you could tell me? Really I think you have your motor with the magnets you showed where you just twist the turn and the magnet is turned off, that's all you need and that can be powered by solar making it virtually free... I'm guessing the guys in washing tin cans and their men with weapons already has been doing this for a LONG time...

@RoelVandePaar 4 года назад

How about using 4,6,8,... arms so the offset between is smaller and higher force and speed can be achieved with smaller magnets?

@brettkarling5671 Год назад

Dude this so fucking amazing. I feel like even with a small amount of electrical energy providing the sliding motion of the slide the rotating part may produce more, and I think would produce more energy than it would require to move the slide back and forth. Especially when on a larger scale because the amount of energy to move the slide wouldn't scale the same as the energy out put of the rotation. In my mind you just made free energy my guy. I really hope you're ok haven't posted in awhile. I want to work with you and help fund your research.

@ramev282 Год назад

Exactly my thought

@7gone Год назад

Same as me, I have plenty good ideas, but dont have working place :D

@Motionmagnetics Год назад

Thanks. You may be right. I've been active lately with new content and am currently 3D printing parts for a new project I've been working on for a couple of weeks. Should have the video up soon.

@jimmysyar889 Месяц назад

What you feel is completely wrong. You can't produce energy from nothing.

@JanMartinusSlootmaker 4 года назад

The world is a better place with bright souls with great courage like you! Thank you

@williammeador2181 3 года назад

you are lost if you really believe

@rikkardo9359 4 года назад

Thanks for calling us viewers intelligent. Here are things I noticed with my intelligence: This model was not ment to be just a demonstration oof the principle. It is simply too expensive and built too precisely. You could have just shown the principle without building a permanent model, like you did it in your other videos. This leads to the conclusion, that you built the motor to work. Well, it certainly didnt work, else you would have shown the running motor. But because you are so convinced about the existence of free energy and because you invested so much time and money in proving it, you just blame it to the model's quality. There is a simple explanation why none of your projects worked in the end: There is no free energy and thermodynamics is not a lie. It's up to you to decide whether to give up or to keep on trying. If you get only one of your machines working, the nobel prize will certainly be yours the following year.

@omorganstudios Год назад

Agree...just prove that the energy into activating the switch is more or less than the energy lifting the steel plate. This should have been the first step before building anything.

@daenghalim3221 6 месяцев назад

Anda seperti orang baru kenal internet dan youtube. #energi bebas itu ada, baik dari matahari, magnet, air, batu, dan berat beban/gravitasi. #orang2 yang telah sukses membuatnya menjadi meninggal ketika ia berterus terang penemuannya. Di belgia inventor mati setelah didatangi beberapa orang. Dan itu tidak hanya di belgia. Di negaraku sama. Demikian pula di singapura, thailand, dan australia. KECUALI Mereka mau bekerjasama dengan pemerintah. Anda paham maksud saya? Di tempatku malah sekeluarga hilang setelah menemukan konsep bagus dan dia tidak mau kerjasama dengan pemerintah akhirnya tamatlah riwayatnya.

@kingofcastlechaos 3 года назад

In 1983 I met and married into a wonderful family. My new father-in-law was a college professor. I showed him my idea (nearly identical to yours with angled magnets and axial in nature) and he really ripped it as foolish and I dropped it. WHAT AN IDIOT I was. Don't listen to anybody giving you crap on this idea. Back then we did not have 3d printing, CAD, overnight shipping, etc. You can do this!. Come to think of it- I actually can do this since I never threw out my original prototypes. They are coathangers and shelf brackets, OMG they are ugly. Thanks for sharing!!

@DBowling11 2 года назад

I would recommend using square (ore even rectangular) magnets so that not only the area of the uncovered magnet and covered magnet are the same, but that the magnetic forces are the same. I have done similar experiments and discovered a WORLD of difference when I went to square magnets. Look at the drawing at 5:19 in your video, and the difference a square or rectangular magnet would make.

@mikesetbacken7891 3 года назад

About 12 years ago I used to fallow the Peswiki page ,whitch has been dismantled..for unknown reasons... it was a sight that had up todate of all technologies . There was a guy who had a very similar device like yours. Different but doing the same thing.. I contacted him .He said it was working ...I have been working on my own design for years now.. Nice work ..

@RAFAEL_ANRIAL 3 года назад

Привет! Мой друг который имел генератор свободной энергии показывал мне схему как сделать магнитный переключатель где затрата на переключение будет 1 вт,а сила притяжения будет 200кг,которую надо накопить в маховик! всё это работает, переключение электрическим импульсом Hello! A friend of mine who had a free energy generator showed me a diagram of how to make a magnetic switch where the switching cost will be 1 W, and the gravity will be 200 kg, which must be accumulated in the flywheel! it all works, switching by electrical impulse

@kugle1000 3 года назад

Так вот от куда ты черпаешь идеи для своего проекта :-)

@DJIzzyDC Год назад

Also you are correct that wind turbine low RPM magnetic Generators are the best candidates for this, as i just ordered an 8KW one that i am going to power with one of these inventions

@petergedd9330 2 года назад

Those fidget spinners are totally inspired, what a great idea. Thanks for your openness, thats not easy!

@crohkorthreetoes3821 Год назад

Your contribution is very much appreciated

@DJIzzyDC Год назад

I have seen designs that rather than using a magnet and shielding it when required, they use an electronic coil that produces a magnetic field, then all you so is somehow switch that magnetic field at the precise time and this would solve the problem, and the coils could eventually be powered by the generated electricity of the generator

@BobWidlefish 2 года назад

Thank you for sharing your work!

@saifudinzuhri9759 4 года назад

I think you need more energy to switch it on and off than just what the rotor can produce the energy. So try to add flyweels big enough on your rotor to add more energy to your rotor..

@Invictuss 3 года назад

Input VS output will always have the same outcome, adding a flywheel will just delay that.

@kingofnothing2260 2 года назад

I appreciate your process. I work similarly. Keep working on this. There is no free energy, but working on design increases your skill of design and production. Great life skills. I am working on a few things myself.

@airmetalmedia Год назад

There is free energy, we just haven't cracked it yet.

@v10squirrel 2 года назад

With the iron bars spinning pass the magnets I’m curious to see if they would become magnetized also. Thanks for sharing

@CYBERshaders42 3 года назад

Good ideas for making the world a better place.

@inertproductionsalternate9114 3 года назад

Haven't seen anything from you in a while. Everything alright?

@bolagadalla 3 года назад

Imagine him figured out how to do it, now the government has him in some room out in no where making magnetic generators for him lol.

@bolagadalla 3 года назад

But yea, tbh thought the same thing

@jdjizzle 3 года назад

I had been following this guy for few years and feel the same why kinda odd how he seemed to be close the nothing for a year

@jacobgreen3415 3 года назад

He got sucked into the magnetic multiverse

@officialjayee9688 2 года назад

We need to find this guy!

@RoelVandePaar 4 года назад

Uplifting and a cool approach. You rock.

@shahjahan8 3 года назад

I love ❤️ your patience about making magnetic moter

@teresashinkansen9402 Год назад

Its so funny how so many people think this is possible but there is no free lunch, the energy needed to move the shield in place is always equal or greater than the energy the magnet gives to the rotor, magnets are just like springs.

@BolivarTavares 4 года назад

expandiu minha mente, obrigado pela idéia e o conceito... vou aplicar em meus estudos e protótipos... chegaremos lá....

@Motionmagnetics 4 года назад

Obrigado. Eu agradeço.

@dustind3502 4 года назад

I see you are working from mechanical switching, I would like to remind you there would be more limitations on the speed of switching possible vs electronically switching, and suggest you work for more torque vs RPM to help eliminate mechanical wear and noise generated from mechanical switching.

@easycheese6409 3 года назад

I would have went with a cam or swash plate for the switching, but it's builder's choice.

@joshuanorris9785 3 года назад

@@easycheese6409 how are your designs going guys?

@916619jg Год назад

That magnetic switch is awesome!

@Traderhood 3 года назад

Brings back memories of Steorn. I am pretty sure what they’ve got worked. They probably either shut them up or paid them off.

@geauxracerx 4 года назад

Seems like you could accomplish the same goal with less expenditure by replacing the moving shield with a pulsing electromagnet/magnets. That pulse at the right time and push/pull the rotor through the flux of the magnets. Great work as always though

@steve-o6413 4 года назад

He works solely with magnets...

@geauxracerx 4 года назад

Steve-o yeah I get that, but it still seems like it would be 10,000% more efficient. The power required could literally be produced by the stator and have tons left over.

@Motionmagnetics 4 года назад

Any electrician could do that. And there's nothing wrong with it, but that's not my overall goal.

@geauxracerx 4 года назад

Motionmagnetics yeah I get I’m leapfrogging the goal of make a machine run by nothing but Magnet part.

@williammeador2181 3 года назад

@@Motionmagnetics what would be your overall goal? free energy

@johnsonmonsen 4 года назад

Great, thanks for sharing! You could show the working assembly on April Fool's Day. So no one would consider it as real - except your loyal followers. There so much fake overunity devices out there. Would there anything "suspicious" about your device? Back in about 2005, when Mike Brady (Perendev Motor) was in Germany, there were no way to get a look at his device. I've gotten him on the phone but there was just an announcement for further official presentation which unfortunately never happened. Back then my English was very poor and from this time on I was curious about the possibility to have a look at a self sustaining magnetic rotator. I remembered because you showed the Perendev video at 2:00. All the best :-)!

@jimmysyar889 Месяц назад

There is no such thing as overunity

@overunityinventor 3 года назад

The best thing about your videos is that you record them first and add commentary later. It makes them more professional. 👍

@jimmimak 2 года назад

Can you use a cam or linkage or gear arrangement to move the shield in front or of the static magnet, or move the attracting magnet out of the way once the rotor magnet/steel bar is passing? I don't think the static arrangements will work, but a dynamic mechanical solution looks possible. You can get magnetic shielding materials such as Mu Metal. Some nickel based alloys are good too. Iron or ferrite that hasn't been magnetised might work. I once opened up a hard drive and inside there was a powerful neodymium magnet which had a shield bonded to one side. It was almost like a monopole; the shield was so good that there was almost no magnetism compared to the other side. I think the shield was made from stainless steel, but I'm not sure which grade. To those saying it's impossible and breaks thermodynamics: It's not free energy, because manufacturing magnets is energy intensive, and their force diminishes over time. Think of a magnet as a battery or capacitor that instead of storing charge, stores magnetism.

@otakatekmatok 3 года назад

Mantap,,mamper di cancel otak Atek motok.motor lestrek ngecas sendiri.gk usah ngecas di rumah.

@walterhynson2898 2 года назад

you could use an electro magnetic to replace the shielded box magnets and slider ,simply reverse the polarity of the electromagnet at the right time

@anim8dideas849 Год назад

that using a lot of energy

@mohammad-mahditaghipour4307 4 года назад

Thank you very much.

@Motionmagnetics 4 года назад

You're welcome. Thank you for watching.

@trench01 3 года назад

You know even a 10 second video saying you are ok would be good to know since its has been a while.

@gUVUsKgUVUsK Год назад

Thank you for sharing Would a spinning disc, rather than a rocking table, perhaps require less energy to overcome inertia on each cycle?

@jdikoder 3 года назад

With all due respect may I suggest: I think you have already consider thar you have 2 magnets at the left and the right of the ball, and below you have gravity, so you have kind of 3 magnetic forces around (I think you have already considered gravity long time ago) Have you tried putting magnets not at the sides but at the top and the bottom of the track? (Maybe you can also use a sylicon transparent hose or other materials for the track to reduce friction. (I can be totally wrong but hope my suggestion somehow ;) )

@panzerofthelake4460 4 года назад

If anyone rebuilds this PLEASE upload a video (without monitaricization) of how long it spins I'm kinda too suspicious but concidering the guy is a genius, this should kinda work

@ronaldd2154 4 года назад

Lol, he won't show a "working" model. Only claim it "should" work. If he does, he won't be alive for long.

@panzerofthelake4460 4 года назад

@@ronaldd2154 lmao U believe that they follow people who build working "free energy" aka overunity devices? Damn, it's 21st century nobody's gonna kill you for this

@ronaldd2154 4 года назад

@@panzerofthelake4460 You have no idea...... Overunity means end of the slave trade which means hundreds of thousands, if not millions of vultures, leeches, parasites won't have power/control over you anymore in a very significant way. You really think they'd let you get away with destroying their way of life and agendas?! They rely of you. The last thing they want is freedom/choice. Overunity if it ever does become mainstream will only cause a global war bigger than anything ever before. How many businesses would shut down if people decided "ahhh fuk it, i don't have to go to work today, or tommorow, or ever if I dont want to" The only reason why they are transitioning from petro-dollar to renewable "green, solar, wind, healthy" bs propaganda (yes its cleaner) but is so you pay AGAIN for it, and with everything being converted from analogue to digital /Electric means they can track you anywhere, anyplace, anytime. We're all just animals in a giant cage, zoo, and its a matter of time before "Quantum" tatoo / micro chipping people will become the norm. Like Norton/mcafee antivirus for computer, so will it be for humans, your taxes will pay for a subscription for Mandatory vaccines, and optional for others (to make it look like you have a choice). All just illusion. Look up Edward snowden and surveillance, look up how your data right now is being tracked, everything you type, everything you view, everything you DO on your phone. People are business. Middle-class eventually won't exist, just rich and poor. With robotics and renewables comming in, millions of basic jobs will be wiped out for us, even though it will also create jobs (they will require higher levels of education and overall intelligence). Elon musk is working on his neura link in an attempt to stick a digital interface to the human brain.... Now that will give you an advantage over other "normal" people when looking for a job in the future, but you certainly won't be human anymore. This system is not under true democracy, but hi-jacked by evil. Globalist cabal networks rule it. They are trying to monopolize anything and everything including nature itself. It means they are armed with weapons and tech so the other 95% can't fight back, and we are only further supporting them to our enslavement ..... I leave you with two quotes, hopefully they make sense: "The devil doesn't sleep" "In times of peace, prepare for war"

@joshuanorris9785 3 года назад

@@ronaldd2154 how is your design going guys?

@panzerofthelake4460 Год назад

@@ronaldd2154 damn.

@DQuale 2 года назад

try using a ring magnet with a rotating iron shield in place of your hole shield, I used it in my lenzless generator with success, there is no drag when you rotate an iron piece parallel to the surface of a magnet, stay away from attractive elements in designing a magnet motor, it will always fail, use only repulsive effects to cause rotation.

@Mike-ff7ib 2 года назад

The key is to eliminate the energy lost. In every case the energy gained is canceled out with friction and clogging. Magnets have energy to harness but to date no one has figured out how to do it.

@airman16105 Год назад

Have you thought of using Mu metal? We use it to block magnetic fields around compasses it would lighten the slider. You can buy it from an aircraft spruce and specialty. Great project.

@davef5208 2 года назад

Everyone likes to make myth busting (or fake) vids on perpetual magnetic motors. But, I still believe there's a way to line up magnets in the rite order, that you can make it continue to work, without a power source. What about those lock switching magnets? what if there's a way to make levers/arms, and maybe counter weights that continue to switch the magnet on and off, therefor it continues on it's own.

@bradley5819 9 месяцев назад

How much energy does the switch use? If too much then game over.

@dumbcat 2 года назад

i've spent a lot of time looking into PMMs. yesterday i prayed and asked God if i was wasting my time. then i watched the beginning of the documentary "A Machine To Die For" which believe it or not i had never seen. in the first 10 min i heard, "you are in danger of becoming obsessed by perpetual motion and spending the rest of your life divorced from your spouse and married to a machine." i seriously doubt that was a coincidence

@nobulistic 3 года назад

I have taken inspiration from your machine to build something similar with the materials I have to hand. I used 2mm thick mild steel temporarily to prove the principle and if it worked I would have purchased some MuMetal sheet. I believe it needs a solenoid to rapidly move the shielding at the precise moment. Obviously to be over unity, this will require the machine to generate some electrical power for the solenoid and control circuitry. My present oscillating disc method is not suitable for high speed operation, a lightweight sliding shield would work better, which I will experiment with. A rotary shielded disc would be ideal if the required timing could be achieved, but this is complex. Here is a video of the machine I produced where I have demonstrated the required fast movement of the shielding disc to achieve rotor motion. I could reduce the air gap between the magnet and the shielding but I don’t believe it will make it run. The answer seems to be rapid movement of the shielding material. The small magnets underneath the disc smooth out the transition and provide end stops. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-n6ZMapMgf94.html

@MrWeb3 3 года назад

*no offence you don’t understand magnetism*

@ronaldreaganwasthedevil 7 месяцев назад

What mistakes does he make?

@ashercorbett8089 20 дней назад

*No offense, but you don’t understand magnetism No offense, but you don’t understand grammar. :)

@primemac3dstudio18 2 года назад

Speculation is that the metal used is causing a fluctuation in the magnetic field and that is why the filed is not steady. It would be wise to remove all metal except the mail metal areas and magnetic. The field pitch is of value so you may want to a magnetic field visualizer to see what the filed is doing. The best way to move forward to to see what the field is doing in your project. I suspect you will see a magnetic spike do to the extra metals. The key is to locate the end bridge of the field. That field is the key to creating perpetual motion

@ModitRC 2 года назад

Literally have been experimenting with this albeit slightly different.

@madtscientist8853 Год назад

If I'm hearing you correctly, what you're basically saying is you made a mechanical pulse width modulating motor.

@mr.upcycle9589 4 года назад

You can man 👍😁

@randolphsnyder1505 Год назад

I am a old mechanical engineer and have always thought that magnetic attraction forces might be harnessed using levitation ,of course, if you read the 200 year old Earnshaw theorem and understand it, you will come back to the same seemingly impossible problem of intermittently blocking or turning off a permanent magnets field.

@andyearl6784 Год назад

Clever man, I love the comments from negative viewers: noun: one that views, not one that participates or one that thought of, unless you have thought of or participated then your no more that a viewer! Probably sitting on your couch with a bag of chips wondering why your wife and kids went for milk and you’ve not seen them since, if you’ve nothing constructive to say,

@Jamesrealasdeath 4 месяца назад

Okay, couple of things you did wrong. Number one you're working on attractive Force rather than repelling force. Number two just build it like a standard engine. You have what I call the mag valves at the top of the engine working like the valves on a standard engine. The Piston will be made of a high-powered neodymium magnet, with the mag switch at the top of the cylinder. This will have a cam that rotates the mag switch on and off. Once the mag switch is turned on to its proper polarity it shoves the Piston down due to repelling forces. Then you really don't have to worry about modifying anything else about the engine, it'll function and run just like a regular engine would. Make it happen captain.

@ashercorbett8089 20 дней назад

He can’t work with repealing force, because that would require the use of a “static” magnetic field If he used that, it would be attracted to the high permeability shielding material, thereby stalling the motor But using “attraction”, the rods can pass by the ferromagnetic shielding material

@johnnynolan7844 2 года назад

What about a wheel on one end of the shaft, that spins a disc like magnetic lock? I had this same idea a while back, but yours is much better.

@TheBlaser55 4 года назад

Thank you very much for what you have shared!!!! Have you considered sharing the 3D models either via direct donation or as a perk via Patreon or something?

@Motionmagnetics 4 года назад

You're welcome. This is more of a test model. If I had one with all the kinks worked out I'd consider it.

@panzerofthelake4460 4 года назад

@@Motionmagnetics :( leaving the poor gang behind

@RoelVandePaar 4 года назад

@@panzerofthelake4460 yeah please share it. That too is being open and collaborating! You say in the video you want to better humanity and collaborate.

@clayscreations9300 3 года назад

@@Motionmagnetics Then we could share Your projects

@nayanmipun6784 3 года назад

No law of thermodynamics says that self-sustaining almost perpetual mechanism can't exist

@5disguised 3 года назад

Imagine quoting limiting out dated laws made buy humans.

@nayanmipun6784 3 года назад

@@5disguised I understand, humans made laws are important and we need good human made laws

@sgteley5181 2 года назад

when i was in highschool i thought of how to huild one and ever since i have had idea of what where and how and so many different possibilities like if you made one that crates power or one that runs an air pump then feeding itself then powering it's own supply then doing batteries or an air pressure tank. the possibilities are endless and world changing if it wasn't made illigal to make unregulated power. EDIT: making use of a weighted flywheel on the side for added motion would help it's to spin an alternator if i am not mistaken

@donaldknee9162 Год назад

Have a better way to shift the plate a flat ring or plate attached to one end of the armature with a wave in it and a 2 pronged guide on the shield plate adjust the position of the wave plate for smooth motion and put a disk brake on the other end to stop the moter for maintenance make sure its balanced and create a generating armature in the center between the metal rods and you have a self powered generation of electric power

@magneticpulseengine3605 2 года назад

Well you are not wrong but switching that field on and off comes at the cost of the rotational force that you had hoped to give you the net benefit of the thing to start with for sure It’s outside the box thinking.

@mtx_by_ovimoto Год назад

Sounds like Charlie Hunnam's voice 🙂

@Motionmagnetics Год назад

I wish I had him to narrate my videos.

@danielrehak4810 3 года назад

Have you finished a functional prototype of a motor with magnetic shielding ???

@mikeconnery4652 Год назад

Have the magnet go over small coils and have the coils connected to a battery. Now you could energize electromagnets.

@Motionmagnetics Год назад

I'm currently building a gravity generator that will do something very similar to what you're suggesting.

@Mrbobinge 3 года назад

Magnetic gating is as old school thinking as Granny told you about. Instead, with zero electrics: get each progressive cyclical magnetic torque to be double each previous magnetic drag. It's in the geometry, baby. I provide, you make.

@GodGuy8 4 года назад

Gods gonna bless you man

@brotherstech3901 4 года назад

This motor design has mechanical limitation on switching however a system of gears can be used to make high rpm motor . Also , moment of inertia is important. Good job sir!😊

@HomicideHenry 4 года назад

My question is just how long can you run that set-up? It looks like it puts out a nice amount of torque. Jesus Christ Almighty God bless you all 😊

@Motionmagnetics 4 года назад

Thanks. This one isn't set up to run continuously. It's simply to demonstrate the principle. The magnets need to be square to properly create a smooth transition from magnet to magnet when sliding the shielding material.

@williammeador2181 3 года назад

@@Motionmagnetics wil never happen.. magnets will not produce a usable force withoutan input..

@hydniq3327 3 года назад

that is a great idea. could we have a follow up video ?

@Timtron432 4 года назад

Very nice!

@oscaralvarez5810 3 года назад

Amigo cuando lo logre es a usted el que le voy a decir primero porque usted tambien a buscado por mucho tiempo 👍

@ottawadigs 2 года назад

you can add small opposite magnets to each end of the slider and the posts so it doesn't bang 😀

@videomang 4 года назад

The main reason a magnetic motor will never work is because a magnet moving near a copper coil to generate a current creates kinetic resistance -- it is impossible to create a motor that will press pass the resistance and create a current. You may in theory be able to create a motor that can maintain a spin that was started by an exterior push, but it is constantly losing speed from friction and force keeping the magnet from moving near the copper.

@kennethwebber1896 3 года назад

I like the way you think interlectual property is use as a tool to divide us and ecourage us to clutch to knowledge in selfish way like the few who who control us.☺

@phuthai 4 года назад

Great.! Thanks for sharing

@redcastlefan 3 года назад

Your channel is amazing. please never stop

@TheRainHarvester 22 дня назад

I missed the reason you didn't show it working. What is it?

@Naomi_Boyd 8 месяцев назад

😂😂😂 All you need is stronger magnets and less friction than I have, and yours will work guys. I'm sure of it. 🤣🤣🤣

@CliveCrawford-p5u Месяц назад

I hope you are still interested in collaborating ideas because I have also been busy over the years with a idea, and came up with a solution for when we put our 2 models together we can have a working model. Let me know if you want to explore my findings

@psecdocumentary 4 года назад

"There are very good reasons for that, which I will leave to your imagination" -- alright, I'll be the one to blurt it out: not wanting to be murdered (literally) by the oil industry.

@norwegiansmores811 3 года назад

or... maybe its because it just does not work? more energy is lost than made so it grinds to a halt.

@NijiflianBustock 3 месяца назад

How much energy does it take to move that metal plate back and forth through those magnetic fields?

@ryanjamesloyd6733 3 года назад

I've wondered about this, ever since I first saw one of those switches several years ago. It seemed, that a better engineer than me, could make a mechanical alternator, with clever gearing.

@dee5556 2 года назад

Already did, It works great!

@Shadobanned4life 3 года назад

I salute your craftsmanship and hard work! Magnets are fascinating and confounding,as the same problems always seem to appear on these devices no matter how they are made or designed,every project seems to end-up 'stuck in the middle' eventually. Some designs manage to postpone this for a couple of cycles but they never really get going under their own power for very long. Worse than that,there are too many dishonest hacks that turn these projects into a battery and motor-hiding contests. If you are enjoying yourself and learning something,you are doing more than lots of people these days! Keep good track of all your data,this problem may indeed eventually yield in small increments. Whatever happens,at least you are having fun,learning,and sharing these nifty vids! Thank You,this is very interesting🌞

@danielrussell2959 4 года назад

I designed one that works on the same principle I would love to collaborate and make a working model my designs improve on the magnetic resonance of effectively shutting off the magnets

@Motionmagnetics 4 года назад

Have you posted any videos of your work?

@danielrussell2959 4 года назад

No I haven't only because I'm not very good at making videos I don't have any RU-vid videos but if you are interested in sharing knowledge and building a working one you can post it on RU-vid all you want I simply want to find someone like minded as you to help make it work I will show you my rough designs and concepts free of charge and if u draw a more detailed design based off them all I ask is that I have a copy so I can build my own

@joshuanorris9785 3 года назад

I'd love to hear about more discovery good sir! Do you have any updates? Thank you

@robertneighbors4091 3 года назад

When you rotate those ferrous rods over your magnets, over time, they will take on the same polarity as the magnets (leading to reduced attraction and /or failure to attract at all). It's very common phenomena.

@clayscreations9300 3 года назад

Is there a better type of material to use

@easycheese6409 3 года назад

Laminate amorphous. It's a form of silicate steel used as the core in low loss electrical transformers, extremely thin, extremely sharp, and known to cause cancer in the state of California.

@tonymontana1774 3 года назад

Great Work!

@intonsoriano5861 4 года назад

You can use spring to make it simple. How? Put spring in the center of your circle move spring bended 45 degrees on surface of disk and you'll found out the tip of spring is moving in circular as well as you move the disk. You can put magnet on its tip and it switches it's polarity as you were trying to do with your project. Try it and you will found out. Bend the spring on your fingers and make a roll

@joshuanorris9785 3 года назад

how is your design going?

@codyshowalter7128 2 года назад

Magneto (Massey Ferguson works) stationary electromagnets (3) you can sort the rest 🫥

@codyquist4908 Год назад

maybe use pvc with caps on the end so you dont have to print something that large?

@johnM-Jr 2 года назад

Can you shield the "gate" in a v gate motor? In a harddrive, the magnets are mounted to a metal frame, is that magnet shielded?

@MrTench8 2 года назад

The effort to moved the shield would be reduced if you got the covering and uncovering equal. Square magnets covered by square holes achieve this. Round holes and round magnets with the holes and magnets equally spaced does not due to the opposite curvature of the opposing sides, it creates and elliptical shape on one magnet with a smaller area than the eclipse shape on the other.

@aaaaaa2206 Год назад

I bet he doesn't post working demonstrations of his creations because he wants to stay alive and not commit "suicide", die in a "traffic accident" or of a "heart attack". These are the most common ways inventors who could potentially change the world die before they could mass produce their inventions.

@billnatan536 3 года назад

Thank you for sharing.

@NathanCoppedgeVideos 3 года назад

Though you might want to see something that works without batteries: ru-vid.com/group/PLcttXCrYoAgOH6cemLCCVsBHGibCxC4g_

@earthenscience 2 года назад

I believe the magnetic sticky point can be overcome. I have reason to suggest this based on experimental results. Unfortunately I have no solid data on this, because during the experiment, both the magnetic viewing film and iron filings returned no usable data, so I don't know how it works. The problem is nobody knows how magnetism works. We are like in Plato's Cave trying to master magnetism. Mainstream science youtube channels will say magnets are due to Einstein relativity, then the mainstream science later says how Einstein's relativity doesn't add up and has errors. So the only understanding of magnetism is from a flawed theory that doesn't add up. Maybe there are magnetic vortices but maybe not, some things about magnetic vortex seem unclear, if there is a vortex why do iron filings not move in a magnetic field? I watched a science video uploaded by the Science Asylum claiming that magnetism has curl but 0 divergence, but then the picture they showed (at least to me) looked like it had divergence.