Make the BEST Gas Bottle Wood Stove! 

This guy's way of explaining and communication is out of this world compared to other videos I've watched.

Great info! Beautiful stoves! I have found that when I watch these videos, it's best done from my own bunker, with a warm blanket and a cuppa tea to soothe me when I get scared. Sometimes I have to pause the video, take some deep breaths and do a short meditation before continuing. Hey, it works for me!

The best Gas bottle wood stove I've ever seen.Great job.

Excellent, high quality design & fabrication. Details make the difference between blah/average & high quality! Thanks for sharing!

Great job . So good to watch something being made, very satisfying.

LOL… neighborhood all goes to a concrete bunker while you prep. I can’t stop chuckling… just found your channel, and I think this is the channel for me. Can’t wait to see more cool stuff.

That was well worth the watch! Great little tips and tricks all the way through. Thanks for sharing👍.

Thank you very much for your very helpful tips, you do know some good tricks. :)

I've opened many many tanks and never had a issue, however you MUST know what your doing!! Just spent all day cutting a tank to build a stove for my shop. Excellent job!! Coast of Maine waving

Great job, well done

Thanks for taking us through your process. I've made a bute wee camping fire for in the gazebo and am currently working on a waste oil fire for my shed, both out of gas bottles from the tip

A great video, I picked up your suggestion of a baffle plate design for my own project. Can you tell or show me how you kept the glass in? i like the idea of the 'W' clips from recycled steel tape, but not sure how you set the glass in place with them. Thanks again for a great vid. Winter here now in Oz, so keen to get the glass door made up and installed on my little heater. Currently just a full steel. I'm also finding if 'choof choof choofs' a bit, so I'm wondering if I don't have enough air inlet, or need to choke the flue down a bit. 9kg cylinder, 90mm flue, ~42mm air inlet. Chimney about 1.7m. I notice your air inlets are higher than most and mine is at the base of the cylinder. Cheer, Paul.

Just landed a few empty tanks today. Will be trying something soon. Nice video.

Nice job. Just a thought; Bending the frame sections around the smaller base of that particular bottle, while being a little more difficult, might work better.

Hello,Thankyou for uploading this episode, ace content, have you had any updates from the water filter system/s,anyhows, thanks again, well explained, top stuff,respect, keep smiling, J

You’re funny. I like you. Great job sir. Subscribed.

The steel banding is also used to hold units of lumber together.

Your work is amazing, and I am most likely to make one myself. I love your clever idea of the double burning plate. I hope you get well wish I knew your RU-vid channel earlier but from now on I'll be one of your followers . 😊❤❤12:59

Super cool, I love it.

I'm sold

All the trade secrets Thanks Stu. "Don't say sorry"😂😂😂 Bunker 3:11 you're a hoot😂 (for ACC, no doubt😊) I'm having des jes vous?

Wirebrush comment, yea the wires have flew out into my stomach, Goggles a must on the grinder

#38-✅👍 Just found out that my .. In-laws... Pawned off all of my tubs of homesteading supplies!! All my tools and plans.. Twenty years of gathering, Gone !!! 😮😢!

Great job mate, just fantastic, any tips on where to get the glass for the door without paying for with a kidney, haha. Seeya Rob

Thank you for the how to video I am fabricating one for myself Question does the heat plate on the inside remove or was it welded solid ? And noticed that one had a exhaust damper. Do you recommend adding one? Thank you. Great video

❤

A few things: Maybe wear two gloves when welding, much safer. Flux-cored welding wire gives off extremely toxic fumes. Do you wear a respirator? The welder won't say 'I'm sorry'.

Talking about safety. You should be wearing gloves and long sleeves while welding. The light is unfiltered UV. So you can actually get sunburnt from it.

Very nice work! Just wondering where you got the 3kw capacity from? I was hoping to get somewhere around 5kw for a sauna out of a 9kg gas bottle stove. Maybe I'll need to go bigger?

I have a flux core inverter welding machine as well, It's small and light with a carrying strap.

I just open my tanks then drill a hole in empty tanks with dry ice around my bit and locally on the tank at slow speed, never thoight about building a bunker and doing it remote 😅

Awesome little stove. Love this!!

u'll only were glove's until u deglove you're self

Do you work for the safety department at work? Most folks work in a way that they are comfortable with. I notice you don’t wear gloves whilst welding. You do nice work on your project….perhaps it is appropriate for people to decide on their own to what they do or don’t. Just get over it please! Nice stove!

This is awesome. Really great work! There's real thought and craftsmanship in this. Not a half-arsed cut holes, weld legs job done. The whole video and explanation was really good. It reminded me of my mentor in my first carpentry job, a very VERY skilled cabinet maker. Meticulous in his work and frustrating at times but the end result was flawless. Truly hats off to you my man. These are the skills and effort that this generation lacks, it transfers to all aspects of life. Sad times

I like it! I seems as if your kung fu could be better than mine 😏