Making barrel rifling using steel tubes 

Sounds great! Yes, this works really well and can be made with just an angle grinder, torch and some very basic tools. The end result looked better than I expected, very clean grooves.

Cano calibre 22LR ou 3,57 Magnum?

thank you! I hope it will shoot as good as it looks

Thanks! Let's see the results.

@airsight Idol. pariho kayong magaling gumawa ng airgun. Idol ko kayong dalawa.😊

👍😎👍

Glad you liked it!

Yep, there are many more methods I plan trying

I was thinking you could start with a larger Allen wrench for the steel stock. Machine it to the standards you mentioned, for equal & flat lands & grooves, then heat & twist.

@@DewaSenapanIndonesia 👍👍

@@TheDamnSpot 👍 This was my first time rifling a barrel, and I will still try many other methods

Much appreciated!

Спасибо! Очень интересно 😮

Yep Hammer drill. Or an Air tool

Проталкивать лучше гидравлическим прессом.

@@pcpairgunschannel И да, на али и правда можно купить дорны для нарезей. Я раньше искал по запросу "rfling button" и ничего не находил, но по запросу "helical push drill" они вполне находятся.

@@andrsivohin8167 Круто. Я тоже на токарнике кнопку делаю и на нём сразу накаткой делаю канавки, накатка прямозубая с небольшим уклоном и шагом от 1 до 1,5мм в зависимости сколько нужно нарезов. Смазка на основе серы, талька и коллоидного графита и желательно канал обрабатывать тиосульфатом, как то так.

That would work and I did try it but I didn't achieve as good precision with it. It's about skill so if you can manage to do it and keep the sides consistent in size then you can do it.

👍👍

Rifling gives better results

Sorry, I cannot ship it

Yes, it should be chamfered. It's called "barrel crowning", in the video I did that with high grit sandpaper and an 8mm steel ball, after chamfering the end with a drill bit. That might not sound very precise, but it actually leaves a very fine finish. Some rifle barrels might have different designs, others may have sharp precise non-chamfered ends while others have a deep chamfer. Search "barrel crowning" on Google and check the images, you'll see many different designs. Also, in my case this will not be used for a firearm, but for a PCP air gun.

@@pcpairgunschannel ah, I see, cool! Awesome to learn new things!

¡Excelente! También puedes usar un escariador para hacer las ranuras, si lo giras de la misma manera. Sólo una herramienta de corte que sea al menos 0,1-0,2 mm más grande que el diámetro interior del cañón. ¿de dónde eres? Lo siento, no hablo español. enlace: s.click.aliexpress.com/e/_DDVqDYf

@@arielsgood4972 you can buy precision tubes

¿Cómo lo usarías para moletear? Lo siento no habla español

will use this for a PCP pistol. Stay tuned!

If its not hardened the button will deform and not cut so well. You can also dip it in oil but you need to temper it so its not too brittle

​@@pcpairgunschannel I asked you, if the water for the heat treatment is necessary to be salt water. Is it?

@@Mazarakis_Spyridon Yes, it won't work with just water.

​@@pcpairgunschannel Thank you!

👍👍

because it was only 5.55mm in diameter, that's not enough for rifling. I increased the diameter by doing that, it ended up being 5.62mm

@@pcpairgunschannel 😁😁😁Great, I thought that was likely, but I wanted to make sure.....but did you know why I wanted an Arabic translation? So that I can understand and follow what you are saying. Greetings

@@pcpairgunschannel Весьма оригинально и главное просто. при наличии расширенного разнообразия оборудования есть возможность делать нарезы более технологичней и точнее. я нарезал нарезы спецрезцом изготовленным из шестиперьевой развертки, ленточка режущей части шлифовалась до необходимого размера и длина этой ленты оставлялась на 1.5мм.это и являлось шириной нарезного канала. станок токарный с автоматической подачей суппорта. есть и ускоренная подача, ствол зажимается в патроне. ставятся малые обороты, из ствола выходит приваренная оправка к резаку из развертки. она зажимается в резцодержатель. патрон вращается ничего не происходит и тут включается подача ускоренная вправо. равномерно вытягивает оправку с резцом . при этом выходит и стружка. так как заточка режет металл в стволе. происходит именно нарезка каналов. ваш метод конечно более простой и многим доступнее, но он продавливает каналы. свинцовая пуля мягкая и принимает размер ствола. и даже по вашему методу пуле легче идти по каналам продавленным, они ведь гладкие без всяких там мельчайших зазубрин. ваш метод считаю оптимальным для самодельщиков......удачи вам и желаю быть осторожным с законами.

@@user-qd4bp6kd5m 👍👍

👍👍

Es cierto que mientras lijaba debería haberlo hecho.

@@CarpinteroJesus Hi, there is a link in the description if you want to buy

@@user-ld6te5zr7i it’s just eyeballed, no accurate maths. It still gave good accuracy, check my latest shorts video

No metal cutting tool needs to be sharp like a kitchen knife, rifling buttons dont need sharp edges

The twist of the button forces it to twist around

It's the same as a screw into wood

@@LuluBear974 cools down the Steel faster, making it harder Oil also works

​@pcpairgunschannel At sea level plain pure water boil at 100°C and works just fine. This is why I don't understand the salt part. At sea level, saturated sodium chlorine brine has a boiling point of 108.7°C, and contains 28.41% NaCl... that isn't a big difference enough to justify salt use. Moreover oil also works even though it boils between 200 and 300°C and the higher the quenching temperature the lesser the hardening but still is ok. Do you put your brine in the freezer or use ice cubes to lower brine temperature below 0°C ?

@@LuluBear974 you are right that pure water works too. However its not about the boiling point only but also the thermal conductivity and the density. Salt water is denser and has better thermal conductivity

@@pcpairgunschannel 👍

No difference, they are just different designs.

شكرًا لا يهم من أي اتجاه تدخل الرصاصة، ما يهم هو أن يكون طرفي البرميل أملس، حتى لا تتضرر الرصاصة من أي جانب.

its a blank steel tube, link in description

this is 300mm long, but you can use 200mm, 400mm, 500mm, 700mm... anything you want. this will be used for a PCP pistol.

@@pcpairgunschannel thanku....how can I buying this pcp gun barrel..I want to this barrel..Plzz help me...

@@sonakhuraijam7223 Due to courier policy i can't deliver my own products. You can make it the same way as I did it in the video, you can buy blank tube and rifle it yourself like I did it in this video. If AliExpress doesn't work you can buy it from ebay also, just search "hydraulic steel pipe"

@@RonBateman-vl2wz coming. I am yet to build a PCP pistol

👍

I put a link in the description

so what do you think of this rifling technique?

@@user-ph2lk2rs9e Sorry I dont have experience with gun barrels, this is for a PCP air gun

You could probably Google that,as you well know.give the kid a break😂😂😂

Tienes razón, ya no uso guantes mientras manejo un torno.

Isto é para uma pistola PCP. Vídeos em breve

5.62mm - 5.48mm, 0.14mm

Thank you!! 👍

我将在几周内用这个枪管制作一把手枪。然后我会上传一段测试准确性的视频。

@@pcpairgunschannel 非常期待

@@mrkalikutista8729 I would need more than just a rifling button. Commercial rifling buttons cannot be hammered and need tons of pressure, which will end up costing me a lot more than just 12$

@@pcpairgunschannel you're wrong you can do the same hammering with the cheap commercial one. Or use a bottle type car jack to push the rod instead of hammering it. Google hammer button, it's a good button, im using that one, stay away from those cheap chinese craps.

your mind is so limited

​@pcpairgunschanneive hammered commercial buttons on ebay.. l

​@@mrkalikutista8729 - Fun. You can also buy the stuff already finished. - Unavailability due to local regulations.

Thank you! I will upload testing videos in a few weeks, using a PCP pistol.

@@pcpairgunschannel Waiting.. Greetings

@@srvctek1 whats wrong

A file can be used for chamfering on a lathe, surely. Just dont pull it back and forth

its for a PCP pistol. Check out my latest shorts video, it grouped at 10 yards so well it looks like only one pellet hole

@@No_love69 why?

You are right, I can grind a 6mm allen key to a bit over 5.6mm, but precision is the main concern. This way is much easier to keep the size precise.

why

Хе-хе, це дуже дешевий спосіб зробити це.

@@pcpairgunschannel так отож! Скажу чесно, поаплодував! Удачі у подальшій творчості! 👍👍👍