MAKITA DUR181Z Strimmer line replace / Install new string trimmer line

Подписаться 1,3 тыс.

Просмотров 51 тыс.

50% 1

Here I show you how to replace worn out /used up string trimmer line on the cordless 18 volt makita dur181 single line stimmer / weed whacker
Please subscribe my channel and like this video as its always appreciated. Thanks.
Akuoly 100m Strimmer Line Mower Line Round 1.6mm
amzn.to/3OSLLN8
Makita DUR181Z 18V LXT Cordless Grass Line Trimmer Strimmer Body Only
amzn.to/4340qZN
Disclaimer: The links above are amazon affiliate links. If you use these links to make a purchase, I may earn a small commission at no additional charge to you which helps support the channel
Disclaimer; This video is for guidance only, as any project always wear the correct safety ppe and follow all safety guidelines.
Please also be advised that this video is only a guide and I accept no responsibility for any injuries loss or damage occurred while following this video.

Опубликовано:

14 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 43

@erniepenny221 8 месяцев назад

Thanks Mick, just what was required, regards from N.Z

@jameseruera9642 Год назад

great help, thanks for sharing, maybe try outdoors for more lighting

@micksmaintenanceanddiy Год назад

Thanks,Yeah sometimes the go pro camera can flicker with the led lights in the workshop so kept the lighting to a minimum.

@cherieturner2 12 дней назад

Very helpful, thank you Mick.

@micksmaintenanceanddiy 12 дней назад

@@cherieturner2 You're welcome.

@callmeoz2554 9 месяцев назад

Lifesaver. TY!!!!

@KINNZ94 23 дня назад

Very helpful mate! 😊

@jovosedlar3395 Год назад

Turn the light on, it is so dark and hard to see in the future. Other than that good video, thank you.

@Pb4Au Месяц назад

Good, easy to understand video, thank you

@micksmaintenanceanddiy Месяц назад

@@Pb4Au Thank you

@BulleDK 6 месяцев назад

Thanks a lot from Denmark

@micksmaintenanceanddiy 6 месяцев назад

Glad it helped.

@geertdepickere5501 5 месяцев назад

Hi, I have a DUR193Z with the exact same mechanism. It is brand new but I have a major problem with it: The line keeps breaking (after using it for 30 seconds) right where it comes out of that whole. I then have to each time take out the head, unwind the wire 10 cm, stick it through that hole again, reassemble the head after which I can again use it for another 30 seconds to a minute. Drives me crazy. Any ideas?

@darrenstirrup5516 4 месяца назад

Excuse for asking this but r u aware that u have to bump the line out😂

@geertdepickere5501 4 месяца назад

@@darrenstirrup5516 Yes I am aware of that. But when the line breaks at the exit hole no line sticks out anymore and bumping does not help in that case. And the line always seems to break right there in my case. Looks like a design flaw to me...

@darrenstirrup5516 4 месяца назад

@@geertdepickere5501 hmm sounds like a fault like u say.

@antasosam8486 4 месяца назад

Try another type of string, like round profile (cheap actually) and dont be so agressive on corners. Also check for sharp corners of gadget, this may be defects of manufacture, highy unprobable.