No video :(

Metal Gate Build Using Tigerwood | JIMBO'S GARAGE

Подписаться 261 тыс.

Просмотров 74 тыс.

50% 1

#JimbosGarage #Welding #MetalFabrication I built this beautiful tigerwood gate for a customer and it turned out amazing!
Subscribe to Jimbos Garage: bit.ly/JimbosGa...
HTP: usaweld.com/?r...
Black Stallion Welding: amzn.to/2XJHBJV
Champion Cutting Tool Corp: www.championcu...
King Metals: www.kingmetals...
Grinding wheels I use: amzn.to/2PPdEpo
Buy a Jimbo's Garage Welder holders here: www.jimbosgara...
Camera I use: amzn.to/2CfEFOi
Follow Jimbo:
Facebook: / theofficialjimbosgarage
Twitter: / jimbosgarage
Instagram: / jimbosgarage
About Jimbo's Garage:
Jimbo's Garage is a channel to watch real metal, steel, welding and wood projects.

Опубликовано:

23 апр 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 145

@kustomaf7606 6 месяцев назад

It’s time consuming, but letting the piece cool down completely while it’s all clamped down is the only way I’ve kept things square. And it’s the main reason I spent the money on a fixture table. Love your videos. You keep me motivated. Thanks!

@didadida4279 Месяц назад

🇪🇬Creative greetings to you from Egypt

@francis-paris1629 2 года назад

Bonjour Monsieur, je tiens à vous féliciter pour votre professionnalisme en tant que serrurier, soudeur ... Je me suis abonné à votre chaîne youtube depuis longtemps et je ne rate jamais une seule de vos vidéos. Félicitations et à très bientôt pour une prochaine vidéo de votre part. Bye 🖐️ from PARIS 🌷 FRANCE 🇨🇵 Francis.

@Blue_collar_craftsman 2 года назад

You tack bars on the inside to keep it from bowing. If it still bows you can add a little bit of heat to the inside of the tube and shrink the steel. I used to build Derricks for drilling rigs and we had to heat the bottom of the tubes to get the bow out

@TheModelmaker123 2 года назад

Agree with Tyler on the heating. If you need to bow it out heat the inside and let it cool. From a practical perspective you can clamp it all you want, but the welds cause shrinkage and expansion and as soon as you release the clamps the internal stresses will cause distortion. Unless you have a very rigid frame with lots of cross bracing, you are going to get bowing. Time is money. So, just weld it and make adjustments after. You can use a hydraulic jack, a come-along, beat it or heat it. All will work for this application. With that welding table you can easily perform any of those straightening options as you can lock and pin at any location. The severity may determine the option to use.

@8LARAIDER4 2 года назад

Any videos out there that show?

@Mardy-old-Bstard 2 года назад

I tack the inside of the flat plate (to hide the welds) and it still bows.

@Danny-qp5gl 2 года назад

You're right. That's how I build rails

@bobomounten3098 2 года назад

Right solution for that kind of problem with frame.Big hammer some pieces of wood and everything will be okay 👍On the end we work with metal, it's not some plazma TV 😉 greetings from Macedonia 🇲🇰

@noname-ox4yt 2 года назад

They make a 2" deep lock box Jim.. or at least they used to.. think i got em from Jansens ornamental. On the heat draw from the inside weld i used to just take my torch (can use a rosebud dont have to) and apply an even amount of heat to the first 3 or 4" fron corners of tube on the outside obviously and the opposite draw effect would usually bring the middle back out pretty dam close with the right amount of 🔥. Appreciate the videos dude keep it up 👍

@denniskennedy6579 Год назад

Ive been welding Pretty much all my life ( 75) years & Really Injoy your videos. Proves you Never know Everything, keep making the different types of products & posting.😁

@TopQualityIronWorks 2 года назад

I love how you extended your welding table nice very nice....

@primojimenez5321 2 года назад

Put heat dots with the torch to bring it back!!

@dizzolve 2 года назад

15:45 maybe you could preshim a backward bow into it planning for the warp when you weld the other side

@trg3761 2 года назад

Save the inside corner filet for last. outside corner first, then face weld next, and if you can flip it over and do the face weld on the other-side. then do the opposite face, next like doing up lug nuts alternate your welds. Inside corner filet last that one pulls the most.

@formekinetics691 2 года назад

Cheap hydraulic ram kit from Harbor Freight would help with fixing warp... more control and less noisy or violent.

@robertteap8052 2 года назад

Problem with a hydraulic ram is it pushes in both directions.. so would require stabilising the straight side in many points and fixing a sturdy support for the ram to push against.. a lot easier to just use a 12lb. persuader.

@brunoparma9179 2 года назад

I usually leave the inside to be welded last. Works pretty good for me, I haven`t had this issue anymore. Great job by the way.

@victorshaw7173 10 месяцев назад

Great work! One tip if I may add is to end your welds on your tacks, rather than start on them. Your tacks are "cold" and running your weld over them will help the "cold" tack fuse in better with the base material.

@veredm11 2 года назад

Hi I'm learning a lot from you I'm waiting patiently for the next video Thank you very much dear man

@govsurplus5496 Год назад

you get the torch out and heat on the other side of tubing in same spots as your stitch welds on flat bar

@gregturcotte8778 2 года назад

Beautiful job Jim. Thank you for sharing this. Metal is easier than wood to work with in my opinion, but it still has a mind of its own. Simple & effective fix!

@mc.builds 2 года назад

Great job Jimbo! Always learning something new watching your videos, looking forward to the next!

@staybusybuilding2910 2 года назад

Thanks for all the knowledge. Watching your videos has inspired me to get a welder and tackle some awesome jobs.😎✌🏼

@metalsyndicatefabrication519 2 года назад

Thx for the inspiration on the different gates you build! I ended up building my mom one for her birthday!! Thx again.

@TheDrunkenAlcoholic 2 года назад

Lol your fixing method is so quick it's probably not worth the time to tack some bracing on the frame before welding, good job mate.

@fierro7170 2 года назад

Cut some pieces of 1/2” or any scrap metal same size of inside dimension to lay inside the frame 2 or 3 top middle and bottom that really helps out .. I have a few out of 3/4sq with a 5/8sq inside to slide in and out with a bolt handle to adjust to different sizes ..

@darrylwhite8912 2 года назад

Hi Jimbo love your work I do a little welding my self , I’m learning a lot from you ( from Trinidad 🇹🇹)

@larryvollmar8763 2 года назад

Great looking gate!!🔥🔥 To remove bow I apply a little heat on opposite side with rosebud. When it cools it shrinks back and now usually disappears

@charlesfields7908 2 года назад

Rule #1 when welding, be comfortable.....even if its in socks and sandals 🤣. Jimbo your the master when it come to being comfortable while welding. Great job on the gate looks fantastic as always look forward to seeing your next project 👍😁

@daracus1202 2 года назад

Time's money, always try for a flat weld, less wire and grinding, plus i would only tack at first just in case something get knocked out of whack. Luv videos and the shop.

@rafatrill 2 года назад

Tack tack tack is the key meaning everything including cross braces even if it's temporary before welding everything so u can move around also when welding. They have air Jack's also hydraulic Jack's use to open wider those work also but pretty pricey.

@Nicola_Colonna Год назад

nice simple and functional idea the extension to the counter

@Steve-Z68 Год назад

Quality work and 100% on learning from your mistakes

@volcarak43 Год назад

Awesome video..! i like what you build 👍

@Hawkeye14341 2 года назад

I would love to see an in depth video of how you measure the space, account for the hinges, account for other gaps and spaces need, how you put a straight piece of steel to uneven rocks. And why people can’t just lift these gates off the hinges?

@8LARAIDER4 2 года назад

I just made a door and i left a 1\8 gap for allowance and went to install and it still rubbed on the top frame. I think i used to heavy flat stock and yeah

@philortega6516 2 года назад

Those are his secrets! Lol. Really it's all just math,that you use for the width of the hinges you use ,the with of the gate opening for you application. It's all on you to figure out and subtract, divide. Simple.

@JimmyLee0757 2 года назад

I'm a serious fan of your videos but I just have to tell you that I LOVE the intro, "Welcome to Jimbo's Garage." We had a hunting game for our grandboys, when they were little and the voice and intro sounded just like yours LOL.

@robertstrassell405 Год назад

straightening instead of pounding it with sledge. and since you have a pinable table. pin material and use a porta power to straighten the metal. will give you a more controlled straighteng process

@Abowhuntersjourney Год назад

The only way I’ve found to stop warping on this type of fab work is to tack some braces to the workpiece diagonally in both directions or diagonally in alternating corners 2 seems to work well

@philortega6516 2 года назад

I would like to add to this video. What I do is pre drill thru holes on the angle iron and you only need to go thru the thinner sheet tube with self tapped screws. And then there's less chance of damaging anything.

@wilbrown2116 2 года назад

Get you a Porto power. They come in handy for a lot of situations.

@TheRealSlowhand 2 года назад

Hi Jim, I just got a moment to watch this latest video and, WOW... Not sure I like your idea on straightening but here is what I've done in the past... Run a few long beads with your MIG along the length where the bow is and it should draw in on the side with the bow and straighten in...

@bobjones9727 2 года назад

Beautiful build. If I was ordering I'd add a small medieval type door to peek out of and use all black screws

@jamesadams893 2 года назад

Love the work boots you're sporting in the shop

@wonseokkim8717 9 месяцев назад

당신은 정말 기술이 좋아요 아주 멋지네요 😂😂😂😂😂

@dougsweldingfabrication953 2 года назад

Dang Jimbo... another beautiful project ! Thanks as always for sharing.

@8Ballmfg 10 месяцев назад

Hi Jim. Been a tubing fabricator for 40 years you need a (Monkey on a stick tool). Simple to use, cheap to push or pull tubing.

@calinsandor9518 2 года назад

Hi mr. Jim. I'm a welder and here are my two tips and tricks which I use when dealing with warping: 1)ex. If I have a warped rectangular frame, I just give some spot welds in equal distances from the center on the opposite side, and when it cools it should shrink back straight. Always apply heat to the opposite side where it bent. 2) I use two portable 4 ton kit with a lot of adaptors and a 5 t pull jack using with some heavy duty chain and straighten things out very easily. Sorry, but I never use a sledgehammer to straighten stuff out.

@r.rodriguez4991 2 года назад

You might try a farm jack to get that warp out in a little more of a controlled fashion.

@garyjones2582 2 года назад

That was a quick 30 minutes.. Well that turned out beautiful Jimbo, as all your work does... lol , definitely barbaric, but whatever works.. Thx for taking us along.. Take care my friend..

@jasonturner1045 2 года назад

very nice

@JoshuaSHogg 2 года назад

Exquisite

@andrewiida3802 Год назад

Dude this is great. I wish you would lay that tongue and groove at a 45. I feel like it would give it a snazzy look. Great stuff.

@doprace8335 2 года назад

Nice 👍

@madcapsportsgarage9761 2 года назад

I use my porta-power to straighten a bow like that.

@kevindavis6042 2 года назад

That wood is awesome on this

@alvindueck2104 2 года назад

That sure is a beautiful gate, Jim

@scottm124 5 месяцев назад

fricken amazing love your channel

@paulmorrey733 2 года назад

Thanks Jimbo

@samoandude6838 8 месяцев назад

Beautiful work man!!

@SchysCraftCo. 2 года назад

Very nice Job Jimbo. This is a very nice design. Hopefully you or the future owners get great use out of it my friend. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep making. God bless.

@NCTradeCraft 2 года назад

Hey Jimbo, back when I used to make gates more often or railings, I would use a couple of ratchet straps or a come along to an anchor similar to how a body shop uses a body puller. You could also use a hi-lift or farm jack or any type of streamline Jack or a hydraulic power pusher.

@imtimrich 2 года назад

I reseal/stain my wood fence every year with the same product, it works great and looks great 😊

@hubertrobinson8825 2 года назад

That gate is a beauty love that tiger wood great job Jimbo

@kelaslas2636 2 года назад

I am very impressed with the way you work, and I really want to work in your company, thank you very much mr.

@allinghamremovals4868 2 года назад

Nice

@duncpap 2 месяца назад

Heat the metal up with torch it will help stop the hot spot or hit it with a hammer or press it out

@Brian18741 2 года назад

Wow turned out amazing 👌👏👍

@lakebum6211 2 года назад

I worked at an aircraft company and our weld fixtures had chill bars (I think they were brass) around each weld to absorb the heat. A wet rag may do the same though.

@nstufflebeam 2 года назад

Beautiful Gate, great job!!

@rioganstech9275 Год назад

Can you make a video on how you go to the clients house and do measurements ? And also about settting your post and leveling the gate ?

@cleokey 2 года назад

Outstanding

@scottysiman8154 Год назад

Hi, Thank you for your videos they are very helpful. I just built a gate with some help from your videos. What do you do for the door latch and strike plate on the post i can’t find any videos on how to do that part

@elmobolan4274 Год назад

RICH, RICH, RICH...

@eccentricsmithy2746 11 месяцев назад

Using thicker wall material will help prevent bowing

@Angelcf62 2 года назад

super Nice !! I use a floor jack to straight my sides, I have only made about 4 gates just for my house, learn from your videos :)

@CrazyFilmsofficial 2 года назад

1. Brace every corner 2. Weld alternate outside fillet corners 3. Weld alternate but corners but start from the inside corner of the frame and work your way out to the outside fillet you just welded 4. Then just Weld your inside fillets but still do opposite corners. Probably wouldn't hurt to clamp down to table where you cam either.

@andersonmartins2095 2 года назад

Boa noite. Tudo bem? Esse portão ficou "perfeito", um excelente trabalho. Já sou inscrito no seu canal no RU-vid tem um tempo. E desde o primeiro vídeo que eu vi reparei que você é um profissional diferenciado na área de solda/serralheria. Você tem o dom, meus parabéns pelo seu trabalho. Um forte abraço e Deus abençoe você e sua família. Brazil/São Paulo.

@OGMsAxiomatic 2 года назад

1. Great project, im hoping i can do a gate like that for my yard at some point. 2. Not going to lie Jimbo, I'm concerned about your ungloved hand. Just wanted to remind you to stay safe. If you keep the glove off because it's hard to feel what you're doing, you could try a TIG glove on that hand so that you're protected and can feel a little bit better.

@donsmith9081 Год назад

Agree, especially being a red head. Also need to protect your lungs while welding, grinding and painting-if you want to keep doing it down the road.

@Mardy-old-Bstard 2 года назад

I have a way Jimbo. One day I'll try to do a video and show you. Send you a link. It works almost millimetre perfect every time. I can't stop the plates from bowing the steel without a homemade press.

@ChristopherSalisburySalz 2 года назад

What about putting in some of those locating pins so it can't move while it's clamped? If you don't know how to stop it I doubt I would be able to either.

@gonzalezliu86 2 года назад

that just happens because of the metal shrinkage. i try to put a little bend in pieces that i know are going to get a filler added to them or use a bottle jack and 2x4s after the fact to rectify the warpage as much as possible. I don't think my shop (garage lol) would survive if i missed with a sledge and sent it across the room.

@Okcbill3500 2 года назад

How was the top radius determined? Gap between sections and gate? Thx. Nice job.

@johnsassano8728 2 года назад

I just shoot for a 12 to 18 inch rise from end of gate to center for driveway gates 12 to 20'

@ericrichardson6899 2 года назад

Awesome video, love the work you do.

@STEVETHEBARBER 3 месяца назад

Hi, I'm not a welder yet, but I wanna be, that's why I'm watching your vids. Good stuff btw. I just thought I would contribute or see if I can answer your question about bowing. Would a brace in the middle either wedged, clamped or tac welded solved the bending problem. I know you said it was from heat, but I'm not exactly sure what or how it happens.

@ggcutter4098 2 года назад

nice work

@mojo9620 2 года назад

TO FIX DRAW: Before you weld along the length pull the bar out about 10mm so that after you weld and release the clamps it should pull back to about straight.

@theessexhunter1305 2 года назад

Very neat..

@dizzolve 2 года назад

that stain really popped that wood nice

@JP-rc1nv 7 месяцев назад

Hey brother, love the content … question : on the 1x2 rectangular part with the radius, how thick is the Steel?

@Tig-Weldor 2 года назад

The bowing is happening when you weld the flat bar along the length. To stop it you need to force bars in that are a bit oversize to bow the frame out the other way while you weld it. How much you force it the other will take some trial and error. But to be honest it’s probably not worth the effort if you can easily knock them back out straight like you have.