Minibike Trike Build - With a Differential! FULL BUILD

Подписаться 177 тыс.

Просмотров 90 тыс.

50% 1

DIFF PARTS:
Differential - www.staton-inc.com/store/inde...
Sprocket - www.staton-inc.com/store/inde...
Brake - www.staton-inc.com/store/inde...
Bolts - www.staton-inc.com/store/inde...
Axle Nuts - www.staton-inc.com/store/inde...
BUILD PARTS:
Leading Link Forks - www.gopowersports.com/minibik...
Handlebar Clamps - www.gopowersports.com/7-8-han...
Handlebars - www.gopowersports.com/mini-bi...
Brakes - www.gopowersports.com/mini-bi...
Bearing Hangers - www.gopowersports.com/3-hole-...
11” 5/8” Jackshaft - www.gopowersports.com/5-8-thr...
Jackshaft Nut - www.gopowersports.com/5-8-jac...
Jackshaft Brackets - www.gopowersports.com/adjusta...
5/8” Jackshaft collars - www.gopowersports.com/jacksha...
Jackshaft Sprockets ⅝ 12T #40 - www.gopowersports.com/12t-jac...
⅝” Bearings - www.gopowersports.com/5-8-id-...
Rear Wheel/Tires - www.gopowersports.com/13-x-5-...
Front Wheel - www.gopowersports.com/10-blac...
Front Tire - www.gopowersports.com/3-00-10...
#40 chain 5ft length - www.gopowersports.com/40-chai...
Engine Plate - www.gopowersports.com/predato...
22mm Mikuni - www.gopowersports.com/22mm-mi...
Header - www.gopowersports.com/header-...
Muffler - www.gopowersports.com/rlv-411...
Throttle Cable - www.gopowersports.com/40-miku...
Gas Tank Bracket - www.gopowersports.com/lil-ras...
Gas Tank - www.gopowersports.com/gas-tan...
Gas Shutoff - www.gopowersports.com/shut-of...
1” Lock Collars - www.gopowersports.com/axle-lo...
Seat - www.gopowersports.com/12-mini...
Twist Grip - www.gopowersports.com/throttl...
Kill Switch - www.gopowersports.com/mega-mi...
Build Break Repeat is Proudly Sponsored by GoPowerSports
*Be sure to check your local laws before driving any non-registered motorized vehicle. Do not attempt these activities at home. All content produced by Build Break Repeat is for entertainment purposes only*
CHECK OUT OUR INSTAGRAM! build.break.rep...
0:00 - 1:44 Intro & Parts Overview
1:44 - 4:34 Diff Build & Mockup
4:34 - 9:34 Building Frame
9:34 - 10:48 Assembly
10:48 - 13:36 Test Drive
13:36 - 14:15 Outro

Авто/Мото

Опубликовано:

3 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 102

@megoingfast 2 года назад

Sweet build guys! Bobby at Metal Fab is a rockstar! Sizzling bacon and building a Wheelie machine!

@miketee2444 2 года назад

Coming from an 80s 3 wheeler kid, the main advice on a trike is keep your feet on those pegs at all cost. The tires will climb up the back of your leg and make your knee caps the new contact patch. That's why nerf bars and the mesh nets became popular.

@DetroitMicroSound 2 года назад

No dive on brake! Just like Ernest Earles intended! Cool little trike! Now build one in reverse! 😁

@bryduhbikeguy 2 года назад

I was thinking similar.2 of those front ends,and a bigger single back tire.If 2 feet longer,it'd be a trail beast.

@randyhertzberg7549 2 года назад

I agree with D L , the bronze bearings will not hold a non-supported load...needs a 4 bearing rear end

@reaper666grimm 2 года назад

Nice build. If planning to do some off-road riding I suggest adding more support for the rear axle and moving those foot pegs forward 3 or 4 inches. Nothing like getting your ankle tore up by the cvt from bump. Especially when you're foot wear has strings and not straps!

@bryduhbikeguy 2 года назад

That's pretty sweet guys.A 2nd set of axle bearings closer to the wheels will make is solid enough for hard trail rides.

@adf8382038 2 года назад

When does mass production begin? "DO IT!!! DO IT!!!" (Starsky and Hutch quote)

@kingman2362 Год назад

So professional work greeting from South iraq

@michaelblacktree 2 года назад

Sweet build! Also, I like how you guys are prioritizing college over youtube. Much respect! 👍

@nashguy207 2 года назад

Cool build guys. You come up with some great ideas. Hope school is going well. Praying for you guys and Daniel. Hope everyone is doing well. God Bless!

@Mikefestiva 2 года назад

Nice build guys! Thanks for sharing this with us 👍🙂

@lsj624 2 года назад

Solid rear axle would be much better. Drift it dude!!

@joshvandruff1790 2 года назад

That things gonna be a wheelie machine! 🤘🏻

@dadsfriendlyrobotcompany 2 года назад

I put a P100 diff on my 1800W power wheels build (soon to be double that). Though my variant has a 3/4" axle, but was able to get it under $100. I did also but a disc brake on either side of the diff, so I have differential braking. Awesome (interesting) trike build!

@dodgeme1986truck 2 года назад

1) those differentials are not designed for loads and need bearings at the ends and at the diff or they snap. 2)the rear brake won't work when placed on the diff... The rear brake needs to be placed at each wheel

@levisylvester 2 года назад

Yes the brakes are important!

@shawnsatterlee6035 2 года назад

Technically yes the brake will work where they have it. Not so well in a corner, but going straight yes. Also when taking off and braking it's actually loading the spider gears in the differential, so I say meh, its all good. Lol

@levisylvester 2 года назад

@@shawnsatterlee6035 a bit sketchy but ok... I have a minibike without brakes 😆

@paulbailey4152 2 года назад

Man You guys do some of the cleanest builds on RU-vid keep up the great work you should have way more subscribers than you do

@darrellkelly7614 2 года назад

Seems like footings could go forward a bit and be wider. Nothing ruins a day riding worse than a chain bite. Plus it'll be more comfortable.

@bighomieJ5X 2 года назад

This bike is gonna ride out nice 💯

@foreman4505 2 года назад

Should put a second fuel tank on the other side of the frame so you have more capacity for long rides

@Duane002 2 года назад

You need to move the foot pegs foreword! The way your feet are on them now, your toes are super close to the ground! If your toe catches the ground, it could pull it under the foot peg and shatter your ankle!

@OGTtom 2 года назад

Great build , looks good

@averyanderson6945 2 года назад

That pull start cage definitely looks cool but it dosent direct the air flow off the fly wheel for the motor to keep cool now

@hasve978 2 года назад

Cool now you need to do a spider version with 2 wheels in front 1 in the back.

@RickC8080 2 года назад

Sick Ride!!!

@usmcmos0317 2 года назад

Cool build always thought about doing one and a great looking Chevy pickup in the video too

@danhambrick6331 2 года назад

Cool build guys....👍👍

@funtoytoyschannel5676 2 года назад

Cool build guys

@marcchaffee7751 2 года назад

i made one of these 30 years ago , dam it was fun . used a 6 hp tecumseh .

@ryanwatkins1821 2 года назад

In my opinion a traditional 3 wheeler has a solid rear axel so when you corner you can get it on 2 wheels and ride it like a motorcycle yea a dif helps at slow speeds but you lose that benifit when under power in a corner because your inner tires just free spind because of no load but a cool build as always

@uncledingovlogs 2 года назад

That thing is rad! We should race our trikes 👊🏼

@frenchokie 2 года назад

Very cool

@gregphillips.1312 2 года назад

For that size Engine and such small Wheels that Geometry looks good! I have always wanted to build a Trike, but the legistration for Road going is tough in the UK

@willieshaw2522 2 года назад

Neat build. I'm not sure about the cage style recoil starter mount though. An air cooled engine depends on the shroud to direct the air flow generated by the flywheel through the cooling fins. Take that forced airflow away and you are really at risk of overheating the engine.

@jamest.5001 2 года назад

Mini trike build. Cool, I'm thinking about a reverse scooter trike build, with car seat and roof! Based on a Chinese scooter,

@davediamond1742 2 года назад

I would Yama bond those hubs flanges to seal, and add more gear lube grease ..like the mini trike idea .. looking great.

@edwardkipp4911 2 года назад

How about a link for the frame kit that you used?

@shaharsdechen2537 2 года назад

12:00 tourqe convertor is right near your leg😬

@abyssflight3907 2 года назад

move the brake disk to the wheel and add a second to the other side controlled by a second lever, this would allow you to control the speed of each wheel independently of one another for sharper turns and a more interesting ride!

@smash12a 2 года назад

Yea glad I did mine with suspension all around. Larger front wheel. Front and rear brakes my seat is lower for better cg points while turning with a solid axle.

@scenicdriveways6708 2 года назад

Nice build guys. Next time use a snowmobile engine. LOL JT

@T0tenkampf 10 месяцев назад

you see that type of front end on a lot of the old school trikes made from VW Beetle rear ends.

@shaharsdechen2537 2 года назад

But great stuff as always

@jamest.5001 2 года назад

A fuel tank from 5" tubing, with a tunnel in it from 2" tubing cut in half, with a strap across the bottom, to mount, with rubber around the tube , for extra support, , maybe cut the seat end of at about a 22°-45° angle, with a 1/8 npt, for a 3/16- 1/4" valve and barb fitting, at the rear on one side, maybe both sides to get the fuel from both sides, possibly put the tunnel in shallower on the front end, to make it look better, and help fuel distribution to both sides of the tank, 5"-6" dia, with about 10"-12" in length, should hold enough fuel! With a 1.5"-2" bunch and fill cap,. I also have a old 80cc Suzuki bike missing parts , but in good shape, I'm thinking about making a trike from, being a I have a small 4wheeler axel, that would fit size wise, and it needs a rear wheel! It could be fun!! Put a 420cc engine on it, maybe a 212-224, use the old engine as a transmission!

@elcaminogaming6707 2 года назад

If you move the rear brake to the axle and put another one on the other side you should be able to control which side gets traction and would steer insanely sharp

@mihkus 2 года назад

That diff is going to break in half, it was never rated for the load bearings to be so far in and wheels so far out, thers way too much load on it.

@Earth11111 2 года назад

Build one of these and make it four wheels and 4x4 with a lil more HP

@jimbrown563 2 года назад

Looks like fun, but that Frame is just waiting to crack, certainly not adequate for any kind of off-road excursions, but then you'd need a rear suspension anyway.

@vettepicking 2 года назад

Maybe a sprocket guard and a wheelie bar!

@colejohnson5447 2 года назад

That front suspension looks just like what came on the old Kawasaki klt’s

@donm.1068 2 года назад

Do you guys, by chance, have a dollar amount on the build. Like an itemized price list. I would like to build one, but would like to know what I'm getting into financially before I get started.Also what do you think one is worth completed.

@luisaugustodutrabenites4231 2 года назад

Please tell me you guys at least considered the total flex of the rear axle... Seems to me you are using the rear axle as suspension once there are more lengh outside the frame than in

@FangOfTruth 2 года назад

I wonder if anyone has used the GPS front suspension for the rear of a mini bike?

@tedbackus4754 2 года назад

Just my opinion you should get another silver tank and put on the other side of the bar to me I think it was a cooler as well. And possibly maybe a little bit bigger motor. But like I said that's just my opinion.

@jonbaggarly6969 2 года назад

Need to move foot pegs forward

@geoffreyjones2000 2 года назад

Waiting for the donut

@fuhkoffandie 2 года назад

You know how sketchy that thing will ride with a differential? Better hold on to something cuz that thing going to turn quicker than you wanted to

@RattyFlyer Год назад

Now you have room for a second fuel tank for more range.

@theamericandreamlegba9638 2 года назад

A death trappppp

@nuclearpowerphysics5409 2 года назад

You need a 125cc engine that you can change gears if you wanna go faster and it’s prob better idk

@dylanzrim3635 2 года назад

Does anyone make LSD cores for these diffs? If so try to find a TORSEN one, both wheels will be locked together 99% of the time, only lifting a power wheel creates full slip and turning is enough to overcome the locking force

@T0tenkampf 10 месяцев назад

there are some cheap chinese ones on ebay that actually seem to work, from what I have seen on other trike vids

@jacobezell9521 2 года назад

How did you mount the rear brake caliper

@devdog616 2 года назад

Sleeve it and drift it!

@donaldburkhard7932 2 года назад

Normal sit in front engine so lower center gravity

@nsjosephh956 7 месяцев назад

Would a 90/65/10 tire fit on that exact rim and suspension?

@pullstartpatriot Год назад

what size tubing did you use for the neck and thickness

@sidekick96734 Год назад

Try it on sand! Will it go?

@MrThunderCunt 2 года назад

Man i miss that intro. Its been a while scince ive watched you guys. Do you guys still ride the rotary kart?

@wippitywine2 2 года назад

Were do you buy the axles

@leronadams9667 Год назад

Can I get a hard copy on the parts t née on How you build it.

@israelalcantar8765 Год назад

How is the turns on it mine feels like shit

@franklloyd96 11 месяцев назад

*It can get very tiring but it were it*

@leronadams9667 Год назад

What is the total cost of all the parts you’re using . Can we get a hard copy of cost ?

@javonbrandon 2 года назад

Do I see a motorcycle business later down the line

@eliveltonsoaressoares6108 2 месяца назад

Look, can you tell me what size rim is on your tricycle?

@cliffpalermo 2 года назад

What was that Jerry can fill mod?

@pollyg562 2 года назад

rake might be ok at speed but at slower times might be squirrely

@DJ_CAZZARELLI Год назад

Will someone please recommend an affordable welder for making minibike frames? T.I.A!!!!

@TrailingThroughLife 2 года назад

Aproximate cost?

@saabkingentertainments.k.e Год назад

Can you guy's help me with my drift trike I wanna sit low as possible to the ground

@michpatriot9097 2 года назад

WHEELIEBARS!!!!! Save your tailbone.

@leronadams9667 Год назад

Why do you not give a price

@Earth11111 2 года назад

Them handle bars are two times to high for me is chop em

@yardsausage 2 года назад

id rock it down ze boulavard .

@richg.8092 2 года назад

👍👍👍👍☕☕🍩🍩

@ClumsyCars 2 года назад

i built mine too long ago

@kencsx 2 года назад

Where's Daniel at

@timpriddy349 2 года назад

needs taller bars

@gumballbreath9466 2 года назад

Electric silent

@jthomas3773 2 года назад

That diff isn't going to last long. Back in the day I had a Bulldog with that diff and even though that design had PROPERLY located bearings and brakes, the bushings failed. Also with the Bulldog the rider sat low so in theory the diff made more sense than here, where the rider sits high and can easily take the load off the inside tire. You guys are just copying the common narrow-spaced axle bearings without knowing why. Come to think of it, I don't know why ANY application would use narrow-spaced support bearings vs wide-spaced.

@albertpeterson7134 2 года назад

Build Break Repeat. What Happened To Your Other Partner?

@hybriddyneguy 2 года назад

Bye bye rear axle!

@donvito4884 2 года назад

Wtf is that on the front l

@lennym1273 2 года назад

I use to own a Honda 250R 3-wheeler so I say this with experience BE CAREFUL THEY LIKE TO FLIP A LOT LOL...

@miguelcastaneda7236 2 года назад

Hmm trying to figure how to build on a poor man's budget came across three of old mini bikes sold by pep boys like twenty years ago they were basically a weed wacker motor.. so diff from a golf cart have to check that out