Model 10 Maintenance 

Best Detachable Clipper of All-Time. I was looking around for a maintenance video, this is great.

Thanks for the information on maintaining the Model 10 clipper. I just bought one today and I haven't used it yet. It was great to find this video on maintenance while my clipper is still new. I feel well prepared to maintain my clipper from now on. Thanks again and God bless.

Thanks for the info. My model 10 heats up as well. Within 10 mins of using it, even with a freshly oiled blade, the blades become too hot to touch and the base becomes hot enough to cause me concern. I always take a break to let it cool down, for fear of damaging it.

Great vid dude! My set will be coming in in the next couple of days. Question for you. Would you advise I disassemble them when it arrives and check that it was properly greased before I start using them? Maybe do some pre-use prepping on them so-to-speak.

Thank you for this very informative video!! I just got a model 10 and the instructions weren't very clear as far as maintenance goes. I want to take care of it properly and this video tells me everything I wanted to know!

‘’Ayúdame’’ desarme mi model 10 estando nueva y ya no sé cómo armar algunas piezas del motor 😢

My clipper cuts on and off I replaced the cord but I’m not sure if it’s done correctly I move the cord on bottom and turns on and if I move other way it shuts off should I remove and try putting it back on?

ok man, thanku man.

Hey. I have the model 10 and it seems to loose power then it picks back up. I'm was wondering what's the problem because it's a new clipper that has been used no more than 5 times so maintenance shouldn't be an issue

I remove it to clean then put it back the motor scratches the "brushes" it's not working normally, I cut like few months. Please help out

Did all this. Still runs hot. Needs more maintenance than a vintage car. Waste of time.

does your model 10 run hot?

Great information 👍🏾

Hello I took my model 10s apart to clean and grease as your video stated. I put them back together and there’s a clicking noise and the plastic part moves blade back and forth isn’t moving. Any suggestions?

My Model10 had been running slow and cutting off. I found this video when I first bought it. After getting the brushes this was a easy step by step maintenance plan. fix. My Model10s are purring again! Thank you!!!

the Classic 76 will be eaiser to find as the Model 10 is just release and hard to find. They will both do the same job and take the same blades.

Thank ya god sir!! Specific and straight to the point

Thank you for this tutorial. I'm looking to purchase one and this shows what I'm getting myself into.

how long should I wait after purchase professional use

How often should you do maintenance on the model 10?

Great video, I just ordered a Oster Model 10, this video is very helpful.

I love that clipper!

Thanks for the Info I inherited my dads old model 10 from his barbering days it had been sitting by his koken chair since he had passed no maintenance guide and i need a covid trim

Thank you so much. I followed every step. Your videos really help. I'm loving my Model 10.

So with the clipper on the lever will fall in the slot of the moving blade, with out rounding it out?? Thanks for responding!!!

Thank you this helps a lot...

So clearly. Thank you man !

I clean the grease component out my model 10 runs hot when I turn them on can u demonstrate how to clean the inside of the motor at the very bottom

Thank you for this. These are fine tools glad I watched this video

Great video! I'm pickin up an old progenic from ebay and a set of new brushes from the 50s,is the maintance about the same and will the hinge on the progenic accept the new oster blades and newer brushes.Thxs again great stuff here.

For Home Use (non-pro), one person/one cut, 2 times weekly: (1) How often for Oiling the Ball-Bearing Oil Ports (2) How often for Greasing Mechanism Behind Face-Plate? Thanks!

how often should it be greased

Thanks Dave. I have # 2076.

Why do you need to keep the clipper running then snap on the blade??

Thank you sir!

I’ve cleaned the inside, replaced the grease and replaced the brushes and my model 10s still don’t want to turn on. Has anyone else had that problem ?