Modernize your brace with new gear!

Просмотров 168 тыс.

% 6 970

New woodworkers need a new brace for drilling! Plus an updated tool list! (see below)
More video and exclusive content: www.patreon.com/rexkrueger
Products in this video: (Scroll Down)
Garrett-Wade Versatile Brace: www.garrettwade.com/versatile-9-special-brace-drill.html
Hex adapter for standard brace: www.fine-tools.com/bohr1.html
(Scroll down, look for item #300221)
The following are affiliate links:
Quick-Release Hex Adaptor: amzn.to/3ng8vGS
Keyless 3-Jaw Chuck: amzn.to/3n7jaUx
Ship Auger Bits: amzn.to/2SjLx3o
Freud Forstner Bit Set: amzn.to/36yr2IV
Irwin Spade Bits: amzn.to/3ncv7s2
Diamond Hone: amzn.to/3cQFVr5
James Wright's video on Wood Owl Auger Bits: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bjAomHJ_8mE.html
(If you buy the bits, use James' link and he gets a little commission.)
Become a member of this channel!
Get custom badges and emojis you can use during chats: ru-vid.com/show-UCj4SLNED1DiNPHComZTCbzwjoin
Sign up for Fabrication First, my FREE newsletter: eepurl.com/gRhEVT
Wood Work for Humans Tool List (affiliate):
*Cutting*
Gyokucho Ryoba Saw: amzn.to/2Z5Wmda
Dewalt Panel Saw: amzn.to/2HJqGmO
Suizan Dozuki Handsaw: amzn.to/3abRyXB
(Winner of the affordable dovetail-saw shootout.)
Spear and Jackson Tenon Saw: amzn.to/2zykhs6
(Needs tune-up to work well.)
Crown Tenon Saw: amzn.to/3l89Dut
(Works out of the box)
Carving Knife: amzn.to/2DkbsnM
Narex True Imperial Chisels: amzn.to/2EX4xls
(My favorite affordable new chisels.)
Blue-Handled Marples Chisels: amzn.to/2tVJARY
(I use these to make the DIY specialty planes, but I also like them for general work.)
*Sharpening*
Honing Guide: amzn.to/2TaJEZM
Norton Coarse/Fine Oil Stone: amzn.to/36seh2m
Natural Arkansas Fine Oil Stone: amzn.to/3irDQmq
Green buffing compound: amzn.to/2XuUBE2
*Marking and Measuring*
Stockman Knife: amzn.to/2Pp4bWP
(For marking and the built-in awl).
Speed Square: amzn.to/3gSi6jK
Stanley Marking Knife: amzn.to/2Ewrxo3
(Excellent, inexpensive marking knife.)
Blue Kreg measuring jig: amzn.to/2QTnKYd
Round-head Protractor: amzn.to/37fJ6oz
*Drilling*
Forstener Bits: amzn.to/3jpBgPl
Spade Bits: amzn.to/2U5kvML
*Work-Holding*
Orange F Clamps: amzn.to/2u3tp4X
Screw Clamp: amzn.to/3gCa5i8
Get my woodturning book: www.rexkrueger.com/book
Follow me on Instagram: @rexkrueger

Хобби

Опубликовано:

7 окт 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 794

@userjjb 3 года назад

Rex, I appreciate you publishing a "negative result" video. In science, papers that fail to prove the original hypothesis are often not published because they aren't sexy. But sharing what *doesn't* work is just as good as what does, even if it might not make for as satisfying a result. I've been holding off on buying auger bits I've seen at flea markets, but now that I know there aren't great modern replacements for bit braces I'll be snapping up good ones I come across.

@hartleymartin 3 года назад

I bought my augers from a vintage tool dealer. Not cheap, but mine were about half the usual price because the box was falling apart and was missing the cardboard labels, so less attractive to collectors.

@quickcodecutter 3 года назад

I was in the process of writing a similar reply when I saw this one. My sentiments exactly

@quickcodecutter 3 года назад

I was in the process of writing a similar reply when I saw this one. My sentiments exactly

@AnimeSunglasses 3 года назад

SECONDED!

@BY-bj6ic 3 года назад

hear, hear. Right on. It can't be moon beams, kittens, and rainbows out the wazoo everytime.

@MrJohnnyboyrebel 3 года назад

I have my father’s brace and bits that he used to build his first house in Winnipeg in 1952. He owned no power tools, and he and my Uncle Hank and my Papa completed the build by themselves. The house was located at 56 Essar Ave, but alas, it was demolished several years ago because the owners wanted something larger than a two bedroom, one bath house. I also have his original claw hammer, which is lovingly framed behind glass in his memory and honor. Love your channel, Rex.

@PureBloodWNC Год назад

Treasured keep sakes for sure. I only have a few images left of my father now.

@dolata000 3 года назад

"And how do they work? LIKE TOTAL GARBAGE" --- I spewed coffee on my keyboard. Best darned laugh all week.

@aaronknutson2435 3 года назад

The god DAMNIT James was my fav

@H3xx99 3 года назад

I kinda love that you spent most of the video actively trying to get your knickers in a twist...

@WoodByWright 3 года назад

Great talk man. You hit the nail on the head. I have been eyeing one of those braces for a long time now. Maybe someday I'll pull the trigger. If they made it in a long throw, or short throw version I would easily throw $100 at it. Thanks for the shout out.

@donleondevillafana7615 3 года назад

It would be great to see you both work together. Again :)

@yossigilbert1214 3 года назад

You guys are my favorite woodworkers, love your stuff James.

@madtitan9639 3 года назад

Same - I'd have already bought one, with all the extras, if it came in 14".

@MakinSawdust 3 года назад

*_Damnit James!!! bahahahaha :) :) good work friends!!_*

@KrazyKrafter 3 года назад

Long throw? Short Throw? What do these mean with regards to braces?

@viewsandreviews180 3 года назад

Great video. Just a suggestion, being an almost machinist I took measurements of the movable jaws of my brace and made two new blanks that then had 120 degree inner faces (with back spring attaching them). When these jaws are installed my brace works very well with either hex or round bits.

@Swarm509 Год назад

Honestly you could sell those jaws if you wanted to, I know I would pay for a set and I imagine a number of people watching would too. I have a number of braces I've gotten over the years (usually had to take them with bits) so would love to convert them. Or if you have any specs/details maybe release them for us to get local machinists to make them.

@joshuamurphy5073 Год назад

2 jaws and the notch is just 120 degrees? Hmm. Maybe I can file some spares down. Would buy a set, though.

@nkuete 3 года назад

Good for you for admitting that you haven't found a solution yet! Your integrity is a breath of fresh air on the internet. I think woodworkers need to get a little more real about how many bits they need. I highly doubt really anyone needs the FULL set of Wood Owl bits. Aren't we really only drilling maybe three or four hole sizes? Seems like chisels, where you probably don't need every single size

@charlesrussell9312 3 года назад

This. I just picked up about 100 bits at a thrift store, and still do not have a full set. I was like "aw man?", but then realized that I don't think I will ever have the need to drill a 15/16" hole. And anything over an inch, I'll use an expansion bit for it.

@TheBeeFactory 3 года назад

Yes! I have so many chisels that are just completely unused. I have about 10 different sizes, but I find myself going back to the same 3-4 for everything. I will say the only exception to this is probably forstner bits. Maybe it's just me, but I have found myself needing all kinds of sizes.

@joelkevinjones 3 года назад

I concur with the comment about about the number of sizes needed. I have a set of three Wood Owl bits (1”, 3/4”, and 1/2”) that work very well. I use them directly in my vintage brace and I’ve found if I set it to not ratchet that the hold is better. Combined with an old square shank expansion bit, I can most of my larger holes drilled without using my power drill. If I had a egg-beater drill that took round shank bits, I’d be set.

@David-hm9ic 3 года назад

Wish I could help. You've made me realize what a screaming deal I got last year at a flea market. Got a brace for $10 and the guy threw a price of $1 each for the bits or $20 for the whole lot - a BUNCH of them- turned out to be about 40 plus 2 adjustable bits. After a soaking in Evaporust and hitting them with a wire brush there were two that weren't usable, both die to bad snails. The rest just had a patina of age on them and the nickers were all still sharp. Thanks for lifting my spirits! I just spent more to have a shop built than it will ever produce- if you don't count mental health.

@muurrarium9460 3 года назад

I paid more for the brace (different seller) but also found a great deal on the bits (45 euro for 43 pieces, 40 of them where snails). All they needed were a day of soaking and scrubbing (and I just oiled them lightly on principle). Yes, they were still sharp enough to cut my skin from the strat. So happy (I bought them online, so it was a bit of a gamble.)

@vane5736 3 года назад

My grandpa was a mechanic and had a bunch of braces with these socket heads on them. Thanks for showing me how I can make them useful again!

@crashtestdummy929 3 года назад

"I mean really, who else is dealing with stuff like this?" Hahaha! Rex, you are truly informative AND entertaining! Thank you and keep it up.

@elitiesrin9619 3 года назад

Rex! I am using Irwin's "The Original" Auger Bits instead of the Speed bits you used in the video. It works fine for me! Bought Bit Braces because of your videos and recommendations, I have to say, never regretted the decision. -Love from Singapore.

@dallasarnold8615 3 года назад

Good video. When I was new in the Marine Corps as a helicopter mechanic ( 1973 ) we used a three jaw brace or a rotary hand drill ( most often called an egg beater drill ). Since battery powered tools did not exist then it was perfect for working out on the flight line. Fine tools rarely had any issues with drill bits providing quality holes. No margin for error on an aircraft.

@claybowser698 3 года назад

Mainly I am a traditional woodcarver but I've recently started a journey into woodworking using hand tools. My journey so far has been reading The Anarchist's Tool Chest and restoring several brace bits, and old axes. One thing I've noticed reading the book and from several RU-vidrs is they all mention how cheap it is to buy old hand planes and other tools online through eBay. I haven't found that to be the case at all. Most of the hand planes I've seen sell for more like 60 to 70 bucks not the 20 bucks that they speak about. I really enjoy watching your videos and you are very practical and helpful. Thank you.

@stefanharms8545 3 года назад

Suggestion: in my experience, the old adjustable bits gave the cleanest holes, so I think that a modern day implementation is needed.

@jeffclark5268 3 года назад

Oh my god THIS. I’m slowly working through cleaning the rust off of and cleaning up all the “primitives” I’ve acquired over the years in my recently finished garage. Well yesterday I had used the 5 largest of a full set of augers I got this winter for $15 an so finished cleaning and sharpening them. Before I put the stuff away (I was too lazy to work on the remaining 8 smaller bits) I decided to clean the single sided adjustable and give it a quick file. Well I can testify that after a quick test at 1-5/8”, followed by too many holes at various smaller sizes that the adjustable cuts cleaner holes than the already delightfully clean holes of the main augers.

@HWCism 2 года назад

Well now I really appreciate my old compete auger drill set I bought at a yard sale twenty years ago. Thanks

@davidbladen856 3 года назад

The modern bit braces are with the square drive are usually called speed braces. I make engineering apprentices use them for a while before being allowed impact wrenches so they can get a feel for how much force to use. Then hopefully they won't spend their careers snapping things with impact guns.

@larry4674 3 года назад

Rex: "God Dammit James!" me: *sub'd*

@practilectual 3 года назад

Excellent video - your honesty, sincerity, authenticity and integrity make you a highly credible RU-vidr!

@deezynar 3 года назад

Rex, try again with the Irwin Speedbore. This time, take your file to the front edge of each of the nickers to lean them backwards. Then file the inside face to produce a knife edge. That reproduces the same geometry that's found on traditional bits. However, I run into old bits all the time in second hand stores, and they are cheap.

@kylewoods9182 3 года назад

I've thought about trying this. You're saying to rake back the very leading edge of the nickers so that they don't bite into the wood as aggressively?

@deezynar 3 года назад

@@kylewoods9182 Yes, you are correct. Nickers evolved to be like knives, narrow, and sharp on the cutting edge. That edge has to be right at the outside of the circle that the bit cuts. The angle of the front edge should lean back, but that's a relative term. It should slope away from the direction of rotation. The closer to the tip, the further back you get, until you end at the tip, which is the furthest back. Think of using a knife to cut a piece of leather laying on a piece of scrap wood. You draw, or pull, the knife along the line you are cutting. You don't push a knife along a line because the knife will pull the material upwards and leave a ragged edge.

@Vincent-S 3 года назад

Huh. Might try that tomorrow. They're not too expensive individually, so if I mess it up a bit, it won't be a big loss. That said, still gonna hunt around for more square shank bits and one of those expandable ones. Love them.

@deezynar 3 года назад

@@Vincent-S Old auger bits are pretty common at flea markets, and second hand stores that sell any tools. I'd go that route first, but if you can't find any old ones for cheap, buying a few of these modern bits and modifying them for use in a brace is very doable.

@Vincent-S 3 года назад

@@deezynarThanks for the tip, I think there's a second hand store nearish to me that might have a few bits. I've also been going to estate sales for them and end up being a bit picky about condition for main stuff like the spurs, thread and how straight it is, so it's a little slow going. My brace is a Yankee 2101A, it holds modern hex shanks very well! I still intend to get an adapter though to help save the jaws a little for things like screwdriver bits. It's been well used and loved.

@TheLukemcdaniel 3 года назад

Thank you so much for actually linking to his video. So many youtubers will mention another, using their real name, or something that's only part of the other tuber's name making it nigh impossible to track them down. It's refreshing to see someone give proper credit on something like that.

@davidbrautigam1701 3 года назад

Your face expression at 3:14 when you rotate that chuck is like Eli Wallach in "The good, the bad and the ugly" when he builds his own customized revolver at the gun shop. ;)

@papakelt1 3 года назад

"How much?"

@BY-bj6ic 3 года назад

Userjib said it well below: sharing negative results is important. Everyone benefits when we see the errors, mistakes, and misunderstandings. It's one of the things I like about this channel and the youtube fishermen I watch. Those guys show you the missed hook-sets, bad days, etc. It keeps the youtubers human--we learn a lot more that way. Thanks Rex

@contra81 3 года назад

From my experience, I purchased and used the ship auger style bits from harbor freight. HF is cheap, but i decided to go with the "Bauer" brand. I actually used those during my joiners bench build with pretty good results. Worked alot better at low speed than in my drill, pretty clean hole and cuts left, and it made a difference when i sharpened it up too. Even w larger size bits, i was able to make clean 3/4" holes for holdfasts in the bench. The snails have bigger thread for more positive engagement too, and decently priced.

@chuckgoughiii8215 3 года назад

Rex, ya sold me on this Brace. I have been looking at the Garrett Wade. You pointed out some of the items I was concerned about but you put them to rest. Excellent video. I recommend your channel to a lot of folks starting out.

@SteveD328 3 года назад

I inherited my dad's old brace and bit set, great quality brace and lots of really good quality bits from no later than the 1950s. Dad was a carpenter/woodworker from waaayyyyyy back.

@gregoryhempen3643 3 года назад

Rex I really liked the video and the idea of a 1/2 drive brace. I find a lot of braces, bits and other old tools at estate sales and these are not frequented by many tool collectors. I found a rusty brace (outside ratchet) that was frozen solid at one and picked it up for $0.50. I tried all the different ways to free it up but nothing worked until I heated it up with a propane torch and that freed up the chuck that was sprung and got the ratchet loose. Some time on a wire wheel cleaned it up nice. I got a 1/2 inch impact extension set on amazon and turned it down to fit and drilled it for the pin. I have less than $10 in this. I used the chuck adaptors you mentioned in your video.

@shawnphillips2556 3 года назад

Hey Rex, Fantastic videos. I have learned a lot and been inspired in my wood working. As I watched the video, there is one thing I was waiting for you to try but you never did. I work in the trades, and we get clean cuts with cheap tools by putting down blue tape where we are going to cut. I feel pretty confident that you could get very clean holes from some of those more disappointing bits IF you drill through some blue tape. I don't own a bit and brace, but if you can try this, I look forward to the feed back. Thanks Rex!

@robrosegraphics 3 года назад

I was thinking the same knew i would see this

@lalainaichane319 3 года назад

Oh, that sounds like a great idea to me !

@kerryfoster1 3 года назад

Another great video Rex. I've had an auger brace for 40 YEARS. Don't use it much because flat bits are cheap and effective, but it is brilliant for removing ancient flat head screws. Lock it, rock it back and forth until the screw starts to move. Enormous torque is produced, but it can take the head off Then the ratchet starts to work the screw out. Best regards to you!

@ericjames5163 3 года назад

Great stuff here. Grew up with a brace and bit in my dad's shop. Actually he had two or three always set with certain standard bits. I currently use my 1\2" socket brace frequently, and I converted a smaller one to work with 1\4" hex in my small mechanic box. There is always a place in the shop for a good brace.

@erallen97 3 года назад

Great tips! Thank you for the info about Garrett Wade, they even carry bits for my Stanley push drill.

@dkruitz 2 года назад

I've got a rcanvas rollup set of about a 16 bits that I use with my grandpas brace. I don't use them as much as I could but am always impressed at how they make quick work of larger holes. Brace is great to use with extended Robertson bits for driving screws without having the screw slip. Thanks for looking into this!

@user-wj7ns7ef7k 7 месяцев назад

Even though this is three years late, I just had to comment. Thanks for making this video - drove myself nearly to distraction trying to find a solution for the four jaw chuck/hex-or-round shank bit problem. This is a tool I want to use for building pegged log walls and simple furniture in a bushcraft shelter. The solutions you offer here will work very well indeed - way more versatile then a scotch eyed auger, since you can swap bit sizes, lengths and types. Kudos!

@wemike 3 года назад

Thanks for the video Rex. It inspired me to pull out that same speed bore bit I put away years ago because of the tear out. I tried reshaping the spurs/nickers with a bit of negative rake and it made a much cleaner hole though it still took a little bit to get engaged. Don't actually have a brace atm, but tested it with a ratchet on some pine and poplar.

@longbui6068 3 года назад

I just have got an offer from a used tools dealer on Facebook. It is 10 random quare shank drill bits, all came from Japan and still sharp for $11. So cheap, right? 😄 I understand those bits value after watching this. Thank you so much, Rex ❤

@ianbrown7235 9 месяцев назад

I actually have the Garrett wade and I love it.

@drooten 3 года назад

I love these drills! I've several dedicated for specific drill bits which suit me just fine.

@GraemePayne1967Marine 3 года назад

In my experience, the Irwin Speedbore bits are ALSO crappy in a power drill. I think they are mostly use by electricians, plumbers & others that need to quickly bore holes in framing. (I got one to wire my basement, 6 years ago. Haven't use it since.) Appearance is not important to those trades because the evidence is covered up later.

@johncoops6897 3 года назад

Of course. They are called *SPEED-bore* bits.Think about it.

@eloscuro704 2 года назад

Several years ago, I tried to use an Irwin to cut a fat dowel hole in a bed post. Complete disaster. I wish I had had a bit brace back then.

@Depl0rable10 10 месяцев назад

@eloscuro704 just need spade bits or forsener bits. They can cut a clean hole in a power drill with ease provided you do a bit of practice. That being said the speed bore bits DESTROY wood even when your experienced

@hydrochloridrix Год назад

I have come to pretty much the same solution. That’s why I bit the bullet and bought second hand bits on ebay. 2 or 3 here and there to slowly grow my collection over time plus a nice imperial set from the UK to complement my metric ones. Now I’m all set. And I have to say, I love them. I only recently finished my Morovian workbench which I built using ash. I actually ruined my power drill when I started drilling dog holes into it, smoke was coming off of it. With the brace it was no problem at all, so thanks for recommending them!

@hyperionhelios190 3 года назад

I appreciate you were able to show some different information than James. I did watch his video previously.

@apollunai 3 года назад

I had a full meltdown and bought full set of wood owls. I was able to find a set of NOS Jennings bits as well. I now have both. I had been able to side by side them with the wood owls. I commented on this on James Wright's bit and brace upload Rex refers to here. As much as I love the Jennings, the simple truth is - the wood owls are just better. They aren't cheap, but they are a very high value product. I'll keep the Jennings 'cause I have them - but I'd recommend the wood owls, whole heartedly. Well worth every penny.

@havocmaverick 3 года назад

I got a nice two jaw brace a while ago. I found some bits at a restore and even an extension for square tapered bits. After sharpening they work very nice.

@adrianabshire 3 года назад

Hi Rex, please remember that a lot of people are ‘working’ from home now and their may be little ears around so please watch the language... otherwise another great video and I learn something every time I watch you!

@vstraylight 3 года назад

Thanks to a reply on a comment I left on one of your videos several weeks back, I started looking on Ebay for hand planes. I also started looking for braces and bits too, and I got a great vintage brace with some bits for $25 + shipping. They worked great! I also scored a lot of 27 vintage bits for $40 + shipping that were also in good shape and work well. I can recommend watching Ebay for deals on vintage stuff. However, I do want a set of those Wood Owls someday after my skills improve.

@stevelowe5985 Месяц назад

Rex, I love your style of presentation, as always I really enjoyed this video.

@obyvatel 3 года назад

Really an excellent presentation of something I now know that I needed to know.

@danshobbies9004 3 года назад

I really enjoyed this piece. Keep up the good work.

@georgenewlands9760 3 года назад

I bought a keyless 1/2” chuck with SDS shank from Amazon. The SDS shank is gripped really well in the two jaw shell chuck and the regular three jaw chuck will handle most things. Unfortunately, my experience with modern bits has been similar to you Rex. About the best I have found here in the U.K. are Wood Beaver. I’m not sure how widely available they are under that brand name but I suspect they come out of the same Chinese factory as the blue ones at the start of the review, except they are red. The hunt for good vintage bits goes on...

@lemagreengreen 3 года назад

I never even thought of trying an chuck with an SDS shank... going to try that now. My granddad was good enough to leave behind his brace but I wish I knew where he put the bits!

@georgenewlands9760 3 года назад

eggypickle Good luck, let us know if it works for you. I’ve used mine with down to a 6 mm (1/4”) Brad point bit and it runs true ( I use an egg beater drill for smaller sizes).

@joshualowe9841 3 года назад

I really appreciate the videos Rex, you have really inspired me to start moving a bit more into hand tool work. And just this weekend I found a set of those square shank auger bits at the junk store for 10 bucks, not to mention a vintage D-23. Now I just gotta figure out how to get the rust off and sharpen them. :-) Keep up the great vids!

@terencegelo2199 3 года назад

It seems like the best solution would be a collet insert to adapt from a square base to a hex. Sort of like a Dremel collet. It would be a relatively easy thing to machine, and having it fit the profile of the original square base means that it could be used in any existing drill without needing to disassemble the original collet.

@binnsbrian 3 года назад

Great idea . Make one.

@terencegelo2199 3 года назад

Brian Binns I 3D modeled a mock-up and sent it to Rex today. If there’s something there, I’ll put in the actual engineering time and get a couple samples machined up.

@binnsbrian 3 года назад

Good luck Terence.

@MusicalMethuselah 3 года назад

That's a great idea!

@abujahl1725 3 года назад

I have several antique braces, and use them with hex bits via some $10 quick change adapters. It's worked fine for years, now. Stanley makes them, probably a few other companies.

@mcswordfish 3 года назад

Anyone else giggling like a small child every time Rex says knickers?

@AndresLicari 3 года назад

Run nicker run

@PaulStoopNL 3 года назад

Hey Rex. Great show you have going on over there! You asked how your viewers solve the problem of getting drill bits for their braces. I live in the Netherlands and I managed to get a nice set of 28 assorted auger bits form a retired carpenter. Actually, from his grandson who had permission from his father to sell them. They were a bit rusty but I derusted the whole set with a car battery charger, a bucket and some soda and water. I also bought another vintage set of nine bits (metric sizes up to 25 mm) in a nice pine box, all made by C.I. Fall, Sweden. I'm not sure but I suspect there's still a lot of those around, probably even more (than a lot) in Sweden. Maybe you should ask your Swedish viewers about those. -- Best, Paul

@thomassmith9932 3 года назад

I am glad I watch you shows. I got a complete set of auger bits from my boss. I would enjoy a show on how to refurbish the set to use

@AJ-ln4sm 3 года назад

I've always loved smooth, nice shaped knickers!

@crichtonbruce4329 3 года назад

My brace is a "Fuller 10"/4 jaw" #890-1072. I bought it about 40 years ago and it still works fine. They are still made and are about $45 Canadian. The chuck holds both square and round shanks. I collected the bits I have now over many years from yard sales. My treasure is a Greenlee #8 adjustable. With two cutters it has a 1 to 3" range.

@dougmaurer7570 3 года назад

As someone who is looking to get into manufacturing, this makes me want to make these beautiful tools since I know there's a market in despite need

@BCRBCRBCRBCRBCRBCR 3 года назад

The market has to be tiny, but don't take my guess for it, try testing.

@nathanbame4198 3 года назад

Have been working with a rusty and slightly bent set until I found a 6 piece vintage set still in the wooden box. Set me back $90 but was worth every penny for the difference it made.

@br4mble 3 года назад

Just letting you know I didn't get a RU-vid notification from this video despite setting a reminder on the RU-vid app. Since this is a full time gig for you I just wanted to tell you. I think I'd want to know if I was relying on videos for my family's income.

@BarefootBeekeeper 3 года назад

I have one that is around 100 years old. Still works perfectly.

@bennyavelin3890 3 года назад

The last type of auger bits you tried actually works well if you change the geometry a bit. The “nicker” seems to not cut ahead far enough, the solution was to file back the bottom cutting edge. Also the cutting angle of the bottom cutter is way to high, but that can be filed. The end result is a nice and clean hole. I did this on a dewalt bit. But they are not super cheap, but perhaps the same mod works with cheaper ones.

@Reximusprimebeta 3 года назад

I personally own and use a vintage 1/2" square drive brace with my sockets. It's solid and reliable. Paid less than $5 at a thrift shop. Never thought to get a chuck adapter, thanks!

@BruderJacob 3 года назад

Hey Rex, i got my brace bit with square shape inside and 2 braces for clamping. And i got some great augerbits but with a round shaft. So i got some kind of dissapointed. But then i thought, why not shaping the end to a square cone. Tried and it works very well! now i can use them in my brace bit and with my electric drill. even with hex shaped bits that sould work.

@nickademuss42 3 года назад

I was pondering using my old brace and bit set and remembered the woodwrights shop on PBS, now that's some real vintage tool users show. I have seen many of the bits at antique stores all over the south, you just have to learn how to sharpen them, and one of the woodwright shops shows taught that. he's been on the air for over 30 years so I cannot remember the episode. He also demonstrated spoon bits as well. Looked very labor intensive.

@MCsCreations 3 года назад

Great video and review, Rex!!! Thanks a lot! 😃 Stay safe there with your family! 🖖😊

@benjaminfrayser4392 3 года назад

Thanks for the tool review, Rex. I have been wanting to replace my vintage, 2-jaw brace, but it feels loose and wobbly, even with taper shank augers.

@seantierney3 3 года назад

I finally went and bought a vintage Dunlap brace and now you find a modern one that can use a three jaw chuck.

@markywellsboy2182 3 года назад

Wow. For once something is available this side of the pond that is not available over there. Last year my father gave me my Grandad's brace. Dad had it 50 years, so God knows how old it is. It works perfectly and in superb condition. I love using it.

@mikeking7470 Год назад

Just bought the Garett Wade and the 3-jaw chuck is back in stock. Pretty nice. And the four jaw chuck also has a 4 sided hole in the bottom to grab old style auger bits. I have a pretty complete set of auger bits so good to go for now ($20 and a hundred mile drive).

@Ed19601 3 года назад

I was lucky enough to find a whole bunch of those traditional auger bits in a hardware store in Cebu City Philippines. That place was a goldmine for traditional/vintage hardware. It's called Yutivo&sons in Jakosalem St. (For those woodworkers who may find themselves there one day)

@dancingbearbelly 3 года назад

Where in cebu? Im retiring there in next 4-6 months

@Grant2406 3 года назад

I love the somewhat one sided rivalry between you and James. It is so funny.

@NhyraVirakah2 3 года назад

Rex is just a lovely angry wood man.

@fritzkraemer1668 3 года назад

Nice Video , as allways ! Ceep on going ! I hope there ist a good set out there

@stevemiller9608 2 года назад

Made my own from an old brace. 1/2" drive is brilliant, also bought a load of old auger bits and cut the square shanks off so they hold really well in the 3 jaw chuck.

@scott8351 2 года назад

Good idea, any pics on Instagram or anywhere of your setup? I just bought a set of old auger bits, but looking for the brace now. Not sure what to get yet. I see alot in very bad shape. Thanks

@stevemiller9608 2 года назад

@@scott8351 start with a stubby 1/2 " drive extension. Remove the chuck from the brace. The ratchet is usually taper pinned to the shaft. Remove shaft, keep ratchet and pin. Machine down the stubby shaft to fit brace body and ratchet. Cross drill through the ratchet and stubby whilst in brace body. Knock in the pin. Job done. Took me about 2 hours of fiddling about, mainly looking for a socket drive shaft of the right size, they're not all the same.

@bcwrangler 3 года назад

I was fortunate to buy some old wood working machinery from a retired shop teacher and in the lot were a full set of new auger bits still in the plastic wrap

@55mga1500 3 года назад

I just found (buried amongst a lot of other stuff in my garage) a bucket of old auger bits and I collected my 3 braces to put them back into service. I second you talking about how to clean up the auger bits! One of the three braces was my grandfather's - he came over from Scotland as a carpenter a bit less than 100 years ago now - sadly, I am not sure exactly which of the three was his...two of them look a lot alike! I have some snail-type bits that I use in my brace that I will have to go dig out and try to see if they are any better than the ones you tried. Thanks for another great video!

@ibdavidc 3 года назад

Awesome video, as usual. I lucked into a set of 2 braces plus 15 bits for $25 at an estate sale. I've worked with a few of them, and other than having to touch them up a bit, they work fine. I don't have another solution, because frankly I've not needed one. So, my solution is to be lucky!

@MasterYoist Год назад

I picked up my brace at Tokyo Hands a few years ago. It has no problem gripping drill bits that have a hex shank on the end.

@poormanswaycorey9027 3 года назад

Thank you and James Wright. You both havr great chanles and help me learn great deal. I wish I had time and patience to put into my channel but I rath injoy my time in my shop. But if either of you find yourself in Southern Indiana your welcome in my shop.

@congamike1 2 года назад

Oh. They made a slightly improved speed handle. Cool

@jenkins1979 3 года назад

Hi Rex,In the mechanics world of tools they already make a socket style bit brace .Although Yours looks more comfortable I have never tried it.The mechanics one will take all the attachments you show.thanks for your videos.I love them

@prjndigo 3 года назад

auger holesaws are the best, especially a set that comes with the optional guide-rod instead of guide drill

@erok268 3 года назад

What's funny is yesterday I just used modern bits in mine. And had no issues lol

@danielmierop662 3 года назад

Thank you Rex, great topic.

@bensartakamcas1n126 3 года назад

A thought came across my mind yesterday like maybe making a jaw for the brace if it is replacable. also amazing work mate keep it up, funny though I tried wood working as soon as you showed it could be done by anyone and that inspired me. Good day, take care and God bless.

@max-zv7sf 3 года назад

Love the video, thank you for the good work. My experience is only tangential to fine woodworking. I'm a farmer in Argentina, my woodwoking is only in rough carpentry. Bit and brace drills here are actually still produced and are very common in hardware stores in rural areas, along with new auger bits. They are essential tools in building and maintaining fences, gates and rural structures (very isolated countryside, not much money for batteries and generators). Auger bits produced here are abysmal. I made an adaptor for my drill simply using a machine screw of appropriate size to interface with a modern 3-jaw chuck, filing the other side copying the shank of my 1/2 in. auger bit. Now I can use practically any bit I want. I find that simple, high speed steel twist bits work well with the tropical hardwoods we use here, and leave clean holes. Bits made to drill steel require you to push fairly hard, but you can increase the relief of the cutting edge ad maybe thin down the web of the bit if you know what you are doing, and then they work well. I now use common twist bits for anything that isn't too deep or more than 1/2 in. I still use a lot the 1 in. auger, as it works well, and the long 1/4 in. auger for making the pilot holes for spiking large logs and fenceposts together. For the rest, the augers produced here are too awful to use. With this setup, sharp bits, a good center punch and chainsaw bar oil I can even cut holes in 12mm thick mild steel. I know because i had to do it.

@philedgerton7892 3 года назад

One thing I tried that works pretty well is just to grind a flat on the side of a round shank bit. (Or one of the other type of shanks that you cut off with a hacksaw, leaving a round shank). With a flat on the side of the shank, the jaws on most chucks will grab and work pretty well.

@jad4945 3 года назад

You can go months, years even thinking that you're a fully grown, well adjusted adult with a handle on life and the maturity to handle most situations. Then someone says nickers in a video and you revert to being about 12.

@colt4667 3 года назад

Don't get your knickers in a twist.

@terrywarner8657 3 года назад

He he he. He said but ......

@martinoamello3017 3 года назад

Absolutely! In fact there's a ton of things that can make me much younger between the ears. It's the around the ears part that messes me up every time.

@shawnbottom4769 3 года назад

I was gonna like this but the likes are at 69.

@jad4945 3 года назад

@@shawnbottom4769 Only sensible choice given the circumstances.

@schm4704 3 года назад

Unfortunately, I don't have a solution. I found most of my square shank bits at the fleamarket. Once I hit upon a full box of them for five bucks, so I'm good now, but that's not readily available for everyone. I have a mom-and-pop style hardware store nearby that sells new-old stock ones made by Famag here in Germany, but those are like 15-20 bucks each.

@Bbonno 3 года назад

Fine Tools in Berlin sells new bits in the old style made by Fisch... for some €35 a piece...

@breaux2806 2 года назад

I have an old Stanley 10” bit brace but the chuck is mangled so I’m actually sawing off the threads of the chuck and tig welding on a half inch drive so I can get all the versatility of this tool and the quality of an old Stanley. Thanks for the vid, I would have never had the idea to do this without seeing this a week ago.

@DanteDiamonte 3 года назад

Thanks Rex. I use that adapter for hex bits in my brace. Not perfect but satisfying. I am also looking for a solution. Thanks for making the video

@brbilheimer 3 года назад

I picked up a set of auger bits from Harbor Freight. My set word surprisingly well.

@madladpjl 3 года назад

i use that adaptor in my brace, i shim it with a pice of aluminium foil and it works ok

@James-lo5ne 3 года назад

brah. Those woodowl bits are the shit. I bouht the 3 pack and was blown away.

@brianloos1340 3 года назад

I just purchased several new manufactured square shank bits from a company in Wisconsin called ICS Cutting Tools. They are under $10 a piece. I haven’t fully put them through their paces yet, but I ran a few test holes. The 1 inch bit went through oak like butter.

@davidclark9086 3 года назад

Good Stuff. Thanks for posting. I don't have a good solution as I bought all my bits from eBay and am still learning how to get them nice and sharp and that is not easy. In my latest analysis, I think the snail is the main problem and I am trying to work that out as well.

@thomaswalter8355 3 года назад

For shallow holes nothing beats a properly sharpened center bits. I don’t think anybody still makes them but they show up frequently on eBay. For all their faults auger bits are still the best choice for deep holes.

@channelsixtysix066 Год назад

Yes, Rex, I commented on your earlier video. Not sure if it is still there (I get banned from RU-vid occasionally). Like you, I just think the bit brace is one of the all time great wood working tools. I could not have made my Ikea Stuva/Besta shelf system without it. The brace is the only tool for accuracy and control to bore with Forstner and spade bits. For some reason I kept forgetting to purchase one, until I realised I really needed it on this Ikea. So I went to a salvage yard and purchased a 2-jaw 60 year old, Australian-made one. Then I installed a 6.35mm hex drive quick release chuck and left it as a permanent mod. Now I have access to all the readily available modern Forstner and spade 6.35mm-shanked bits. A vastly underrated, under utilised tool I wished I had, 30 years earlier. I've always liked them for their simple ruggedness, but there is nothing like owning one to appreciate how good the brace really is. I'm going to attempt a full restoration on my old brace, but I'm also after a new French-made brace you see online. Since it is new, I will choose a 3-jaw version. Cheers 👍

@averyo2521 3 года назад

Yes! I finally invested in a bit and brace and got a bunch of auger bits. Someday I might even learn how to sharpen the dull ones up. But if I ever need to drive something with a socket or hex shank or round bit... I'm gonna use those electrons. Hopefully someone finds a solution I can use late at night without waking the neighbors but I certainly haven't seen one that's good enough to actually use in place of my drill and driver in the general sense. They both have their place.

@muxmurki1497 3 года назад

Hello everybody, I followed Rex' ideas on mechanical braces and bought a good used one on eBay for € 12.-. Then I got myself an adapter for about € 10.-, which is originally intended for SDS-+ machines and put a drill on it. Now I cam use cylindrical drill bits as well as 1/4"-hex bits on my brace! I will send pictures of it to Rex, maybe he wants to display them.

@skizzik121 3 года назад

I put a few different twist drills in my indexer and milled my own 4 sided shank. Works fine, im sure that of i used higher quality twist drills they would have been closer to round making the square more precise as mine ended up a bit off center.

@Suitednzooted11 3 года назад

Love those old bits in a power drill, machine off the square drive and they eat wood like barely anything made today and they do it with a pretty clean hole.