At 14:30 he glosses over the loop function, for anyone wondering. Function 8 is the number of cycles. 0=Loop forever 1-99=number of cycles to loop Hope this helps others, I've seen quite a few comments about the looping function.
Thanks - very helpful - and this is a critical function. I found a clue to this in a table I found by googling "canton electronics Model IO52B02". Instructions there are a good supplement to what is in this video.
jw, I have a YYB-5 control similar to the one shown here. When I program P1 and short IN1 to ground it only runs the A timer. It does not automatically go to the B timer. When I short IN2 the B timer runs. When I program P2 and short IN1 only the A timer runs. No C timer or B timer. I tried seconds and minutes configurations but it still never automatically goes from the A timer to the B timer. I altered the all times to be sure it was programming correctly. Any suggestions are appreciated.
Amazing video. Helped a lot with my son's technology project. We ordered this from Amazon but didn't receive any programming instructions. We tried for many days but we could not figure it out. My son was so frustrated and we were about to return it, but we came across your video and it was a lifesaver. Very Helpful. Thank you so much.
Very awesome, informative video. I’m doing a little project and needed this little board. You explained everything so well it literally took me 5 minutes to set the whole thing up. Thanks a lot my friend.
To be frank the video is really nice and I liked the way you have made and explained settings . I wish you could help your viewers with their doubts rather asking them to watch the video again. Questions they hv asked were not covered by you in this video
REPEATING (LOOPING) PROGRAM: Several people have asked how to set the board to repeat the cycle automatically. Essentially, parameter 8 sets the number of times to repeat, 1-99. 0 means repeat indefinitely. Default is 1. I found a clue to this in a table I found by googling "canton electronics Model IO52B02". Instructions there are a good supplement to what is in this video. (Shoutout to jw11432 who also addressed this in his comment).
Hello Ahmad, and thank you so much for your comprehensive video. I looks so difficult for me. I am looking for a module to trigger a linear actuator. In fact, I just need the function F-12. By chance, do you know if a simpler module that does just that exists? When the linear actuator arrives at the end of its path, there is an internal switch that cut the power. So, my idea is to set up the time for the same length as the linear actuator, so, when the linear actuator arrives at the end of his path, the module will cut the power and wait for the reversed trigger. Am I right?
Great video. 1. If one cycle of f01: t1 t2 and t3 completed in order to activate it again i need to diconnect the 5v power and connect it again? 2. If i want to do one cycle of f01:t1,t2,t3 and afterward want to start a new cycle of f01:t1 do i need to be program it again?
Hi! Great video! Can this be used with an 110V 750W 1HP Sewing Machine Servo Motor? And can you suggest what wires and trigger to use to initiate a forward,stop,reverse cycle?
Can this be used to control an actuator in the same fashion? Actuator extends for specific period of time, then pauses for specific period of time, then reverses direction for a specific period of time. I would be looking at a 12 volt actuator arm. Thanks!
I’m planning on using 2 of these on funtion 11 one for each 100w 24v dc motors each motor will be moving in the opposite direction at the same time of day how can I trigger this to work on a timer I want it to open curtains at a set time of day then close them at a set time Thank you
I have a YYB-5 control similar to yours. When I program P1 and short IN1 to ground it only runs the A timer. It does not automatically go to the B timer. When I short IN2 the B timer runs. When I program P2 and short IN1 only the A timer runs. No C timer or B timer. I tried seconds and minutes configurations but it still never automatically goes from the A timer to the B timer. I altered the all times to be sure it was programming correctly. Any suggestions are appreciated.
i got the following problem! i fitted this board on the 4x4 - 4x2 system on an ATV...it works like a charm except every time that i turn on the key, it will run for the direction where the switch is on! Is it possible to configure this board in orther that evary time that it turn on, it doesn't run the motor? Thank you for the help! Cheers!
I don’t know exactly what you are using this for, but if you wire it to constant power and not ignition, it will not turn on every time with ignition, instead wire it to constant power and add a normally closed momentary switch on the negative lead of your circuit board, Now you circuit board will only run when this switch is pressed. Good luck to you.
Thanks a lot for this explanation. English is not my native language. But the only question I have, is it possible to set at auto repeat? So for instance forward for 2 sec, stop for 0,5 sec reverse for 1 sec and then forward until trigger van Capatative sensor and repeat? Hope you understand what I mean? Thanks in advance.
you are welcome. have made over 460 videos and don't remember what I said. But when I explain something, I don't leave details. So if you watch this video multiple times, I am sure you will understand all the features. good luck
If i want to connect 220v motor and i want that the mototr spin clock wise 30 seconds and in counter clockwise 30 seconds and than repeat the cycle for 300 seconds 5 cycles. I also want to activate the cycling by push button and stop by stop button. Which connection i need to use? Every time i press the stop key the cycle will stop and every time i press the stsrt button it will start without disconnect the 5v power? I want this setting remain constant. Is it possible?
Thanks for the reply - the problem I was having was I used the same power source for the motor and control circuit. Once I suppled them separately it worked fine. In my final application though, I will only have one 12v (battery) source to power both. Is there a device I can use to isolate the single supply and essentially make it two independent sources? Thanks
I don't remember what I said in the video. but this has different functions. with trigger (when wire is used) and without trigger (without wire). So yes. you can. you have to watch it fully as I have explained all functions of this module. good luck
Can it be programmed in a way, that motor goes forward for desired amount of time, and than backwards for desired amount of time and repeat this cycle indefinitely? What kind of motors does this module support? In the video you used DC brushed motor. Will it work with brushless motor or AC motor as well ? Thank you!
Hello, I believe I've explained the best possible way all features. so if you want watch it fully, you should get the answer. This is only for DC motor as I mention in the video. Brushless motor has special speed controller.
Hey there and thanks for this video, I wouldn't been able to get this done otherwise :-) Is it possible to program this device with Arduino or Raspberry, so I can get some individual timings into it? I would like to have it going like this: forward, stop, reverse for 1 minute, then 1 minute pause and 10 seconds forward, stop, reverse every minute. I want to use it to develop classic film with that ;-) Thanks a million for your help!
@@robojax Hello and thanks for your reply! I'll check some more videos from you this evening after work :-) Is it hard to program this device I053A02 without knowledge of coding? If you like classic photography, I'd be glad to share my results for maybe another of your awesome videos ;-)
actually you can't update the firmware (code) of this. it is sold like that. you would have to use Arduino is the most flexible device and you can do anything you want. there are tones of codes and videos available. Yes I love photography and I spent time taking photos. but how would I use them in my videos? Share please so I look at them.
Can you set this repeat the action continuously? Like forward for 5 seconds, stop for 5 seconds, reverse for 5 seconds then stop and repeat the cycle again ? Also can you connect a speed controller to the dc motor and it still work normally ?
Hello, I have explained and demonstrated all features of this and don't remember anything about it. so if you watch it multiple times, you may understand all the features. but for sure nothing is left out. so watch and find out.
I'm new at this electronics stuff so bare with me, I have two questions 1: can I set option 8 to 99 so the program will run 99 times. 2; I was lost when you said, "9 is that if the trigger happens continuously pressed or just low level we are not changing." what does that mean?
to answer your question about "99 time" I would have to watch the video. So you watch it because I don't remember. your last question, "continuously pressed" means keep it pressed. when you press it, it sends 0V or LOW to the input. you can also use a computer or other devices to send 0V or LOW signal to make it work.
Hello, I just watched your video and programmed the unit. It works, but now it won't stop running the program. F8 is set to one, but it just keeps going. I saw a factory reset option of pushing the ++ and -- buttons simultaneously for 5 seconds, but that doesn't stop it either. Could it be defective?
la ripetizione ciclica (8) funziona solo con F-01 e F-02 e non funziona con F-11 e F-12, pertanto non sarà possibile in F-12 comandare il numero massimo di ripetizioni. cerco di spiegarmi se volete che un attuatore avanzi per x volte comandato dall'impulso del pulsante non funzionerà. infatti in F-11 e F-12 manca il numero di impostazione 8.
hi there, ive got a 24v garage door motor with a burnt out wireless reciver board that does not work, but when i applied 24volts direct to the motor it works under load which works fine to open garage door and close. i just need a replacement 220-240v to 24v reciever board relay with a built in timer. do you know which one should i buy. i dont want to buy another whole garage door opener/closer, when the motor still works. (ive all ready check the circuit board 24v reciever relay timer with i can not find no issues that i can see). ive checked aliexpress but can not find one that suits my needs, please help anyone or send me link off video that can help me out.
Hi. Can I use it without the trigger? Eg. Program it forward 5 seconds->stop 5s->reverse 5s and repeat the program indefinitely without triggering a program every time?
Hi, someone else might reply. I don't remember what I said in the video but that is my rule to explain everything so if you watch it fully, you should get the answer weather you can do it or not.
Why can't you say in yes or no that if this circuit has option to run for few minutes forward then stops there after runs reverse. In you video you have not said anything about loop . That's the only part missing .I wish you could have clearly said in yes or no. Overall I like the way you explained the setting , very nice review .
@@robojax It DOES HAVE LOOP! Quote from the page: "The number of cycles is the number of repeated actions (Nx =0 means always loop, Nx =1 means no loop). So you can set the number of loops: 1-99 times or forever loops." But it did come with 1 as default, so it did not loop and you did not dig that. You are also not aware that most anyone who would need to use a motor would need to loop probably, so an important part you skipped. You are one RUDE person, btw. I have never seen anyone answer this way on YT.
@@x-0-x-0 Dude, thank you _so_ much. I see so many people asking this question (and you're right, anyone looking for this feature will likely need some degree of looping for practicality) and this dude is rudely telling people to watch a 30 min video again instead of taking the time to check...instead of narcissistically postulating that if that function existed, he simply wouldn't have left it out. 🙄
Can you post those text instructions as well - I can't find them on the internet anywhere the item is no longer on aliexpress so the instructions are gone from that site. Thanks
Hi I want to put powerstep on my truck and I search for the perfect module board for me. The motor is polarity. So one way is deploying and switch is stow. By a trigger. (Door). Have to be 3 sec each way. Need 12 volt. It’s on a pickup truck. If you can tell me what’s the best things I need for that Thank
@@robojax thanks for answer; but if you look on youtube for powerstep you will see. i need a timer with the module polarity and its the trigger (open) start the motor 3 sec. after trigger close the motor start in opposite direction for a other 3 sec. Its near of the i053a02 you explane option 9 .. but i dont know . thanks
then forget about this module. it can do only things it is programmed to do. here is ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-JMBgGO07YLM.html the video and start using because you can control it any way you want.
Is this controller a avilable with Solid State Relay instead of mechanical relay? And also can you please make a video for AC motor using this controller
no. unfortunately. You would have to use Arduino. Here are my videos on Solid State relay ru-vid.com/show-UCkcBSig_Iu4ZnAIeCeG1TVgsearch?query=solid+state
@@robojax i have it with Arduino. Ok, so with this I053A02, can you show the wiring please, because in AC motor, i have 3 wires, two clubbed with capacitor wires and one directly to motor, am not into electronic so, just looking for it
Is there a board can control 120V AC motor forward and reverse just 1 button? 1st push go and 2nd push reverse? Thx. To replace a swing gate opener control board. Currently all I can find is for 12 or 24V DC motor.
you can use this module with very little effort. I did not do it because people are just waiting to blame other for mistakes so I did not mention it. please do not ask me but search online how wire AC motor to rotate in two direction and (Now I have to reply safely) make sure you know understand the safety aspects of working with AC voltage. If you are not sure, seek help from a professional.
I am surprised the way you answer questions from your viewer. They already watched the video and then they are asking those questions . Instead of answering their doubts you are asking then to watch the video again to increase your number of viewers. Very bad approach and attitude as not everyone is technically sound like you. Would request to keep a helping attitude . You may answer easily if you know the answer
hi, i want to use it to do latching for water valve-a latching valve require positive pulse to turn on and negative pulse to turn off. Can i set it to forward for 0.1 sec and stop for 15 min and then reverse for 0.1 sec and delay for 12 hours before foward again?
Hi, it has 3 settings. but you want 4. you want extra delay. I've explained it at best possible ways. if the thing you want to do is not possible by this module, then you might need another of this module and some how after motor is stopped (after reverse of 0.1s) then it should keep it OFF for 12 hours. and you can use the trigger feature with some wiring which I don' t know at the moment how. For that you need to check the 1st module and see after the last step which pin or location on the module is changing the state from LOW to HIGH or from HIGH to low and then solder a wire on that spot and connect that wire to the trigger input of 2nd module. Depending on the LOW or HIGH then program the 2nd module to turn ON after 12 hours. then do the same. on 2nd module find the same spot and solder a wire and connect it to the trigger pin of 1st module and it should work. It needs patience. Or simply use Arduino which opens the whole word for you and do anything you want. Program it and upload it to Arduino. See this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-JMBgGO07YLM.html
Hi, I accidently put more than 5v to the internal power and, now the digit panel is showing "r.r. r." and not working at all.. Did I blew up the voltage controller?
Can anyone help me wire this thing? I have a 110v controller sending out one black and one red 12v line to motor. Two wires that’s it. I want to make a 12v mixer motor go back and forth in different directions 2 seconds in each direction on its own. I have a polarity changing switch that works great but I have to flip it manually. I’m just looking to be able to walk away from the unit and have it go clockwise/counterclockwise continuously on it own
Is there a simpler controller if I want to set it to switch polarity forward 5 minutes and reverse 5 minutes automatically and stop in 2 hours with 30Volts DC, max ampere less than 1 ampere? This is just overkilled.
This is very cheap and if you go with anything else, it would cost you more. Here is my video if you want to do it with Arduino ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-JMBgGO07YLM.html
you can't to it with this. you need to have encoder installed on motor so you know how many turns it did, then take some action when it reaches 100 revolutions.
@@robojax Sir I would like to order a "Multi-Function DC/AC Motor Controller Board with 24V motor, 2 relay, 1 display, photo sensors and keypad. The machine should be automatic with inbuilt program set for movement or oscillation.
