Mustang 2007 GT heater hose leak under admission fix for 7 bucks 

Auto shop wanted 600 dollars. I did it myself with your help. Thanks

Big thanks to you Sir!!!! Really helped clear up what I was going to have to do before doing it. If you mission was to help Mustang Enthusiasts...you succeeded with flying colors!

Thank you for posting this. I have that very issue right now and going to follow your advice. THANK YOU! This is EXTREMELY HELPFUL!

Thanks for showing this. I have a coolant leak somewhere in my '06 that I haven't been able to locate. Dollars for dimes, that's it... 👍

Beautiful video thanks you just save my car I was wondering how to fix my car and this video resolved my problem on my car thanks again my friend 👍

Thanks for the video! I didn't know if I wanted to take the top stuff off, but it looks ok.

Thank you so much! I am just having the same issue right now, with my Pony 2006.

Thanks for taking the time to thoroughly show us the point of failure and how you chose to repair it. BTW, I was going to take the route to replace entire heater tube assembly, but dealer kept sending me damaged parts... So I appreciate another alternative. I think your repair could easily outlast the life of using the factory parts too!

Needed that part number to make sure I don’t make a double trip 😂, thanks for the info !

Thanks so much. Just finished your fix to my leak. I didn't take the intake completely off, took the intake bolts off, disconnected the drivers side injector wires, took the air inlet tube with the top of the air cleaner off, and moved the intake manifold to the drivers side. Didn't have to disconnect the fuel line. It was a muther to get the hose you recommended on. I would see if O'Reillys had another 90 degree hose that was just a bit larger inside diameter. I have a 05 GT but with a 09 GT motor. The intake manifold is easier to work with than the 05 manifold. BTW, the 05 motor ate a spark plug. Again thanks for the fix.

Thank you so much did this today saved me some money

hey man actually all u had to do is take the alenator off and you can reach all the way through and fix it i found this out because i had to replace the heat sensor under the intake i learned it from a guy on utube and very thankful i did .take a look if u take off tghe altenator u can stick u hand all the way to the back of the motor from the front of the intake lol hope this helps anyone out :)

Nice job! Thanks for sharing.

I replaced mine with the same hose, then test drove it up to 75mph at WOT. It did not come loose like others claimed it could. If you use new (screw type) hose clamps, the correct hose too, and tighten them down properly (where you can see hose rubber slightly poking out of the clamp slots), it will last long. All my cars over the years get the same finesse with zero issues

Thanks a lot for the video gonna change that piece on my car and save me 500

hi! thank you for the video. Is this the same procedure for the V6 engine?

I just discovered the exact same issue in my car today , I just need this hose part number , I've been adding water to my car every 2 days for like the past 2 months 😂, finally the issue showed up clearly and I can fix it easily

Thank you for the information. I have the part and have the intake off but I had to go to work, will finish tomorrow. Is it still holding up, or any other info you can give me? thanks

I drive an '07 GT and under full acceleration (!!) thereby increased coolant flow/coolant thermal expansion, this Gates hose will be pushed off the metal inlet sleeve at the front of the intake valley. It happened to me and my temp gauge began to glow cherry red and scared the you know what out of me. This video is a great patch but please spring the extra 65$ for the factory correct heater hose. The factory correct hose will snap over and lock onto the metal inlet sleeve much like an a/c or pressurized fuel filter quick connect line.

I've never seen a video were people say torque specs the intake should be torqued to 89 in lbs in sequence

Good man thx

very good! do you need to remove some coolant first ,so that when you cut the old hose , will coolent come out ?

FYI - Ford dealer wanted to charge $700 to fix this on my 08 GT

How did you remove the other end of the hose

I’m sorry What is the inside diameter of the hose, disculpa cuál es la medida del diámetro de adentro de la manguera? It’s the upper or lower hose?

Do you know if the coolant that leaks into the motor steams after the cars been on for a while ?

So is it possible that this hose will leak with the car on or off? Mines is pouring water off whenever i put some in the coolant. It drips in between the trans and oil pan at the bottom.

So how did this end up holding up? Having the same problem at the elbow. Coolant leaks out from the elbow within about 5 minutes or so of the car running. I’m breaking mine apart now. Just wondering if it helped?

WERE U LOSING COOLANT BEFORE U INSTALLED THAT NEW PIECE IN THE INTAKE MAINFOLD?

At the end how do you know it is not leaking under the bottom you just crank the car up and never check the bottom to see if it's leaking again

Hi there, I'm going to replace that part on my vehicle soon as well and was wondering if you drained your coolant beforehand or if that's unnecessary? TIA

What is the part called

Do you have to drain the coolant first before doing this or no?

Do you know what the part number is?

How's the hose going today? I'm gonna make a replacement on mine soon so I am deciding on just buying the elbow or just replacing the hose like you did.

I’m having the same issue leaking coolant and overheating

So was it leaking at back of motor because mines peeing back there

So all that is needed is a 90 degree heater hose

How fast did it leak? I have a 2010 4.6L and I'm having what I think is the same problem.

What size hose? For the 90° heater hose

Hi was it leaking under car

What did you use for the heat protection?

Mine is leaking...does the elbow part pop out so i can replace it? Not doing all this tho...just going move alternator out the way

Hi will the hose size work for a v6

I'm do this on Thursday wish me luck

How were you able to see that it was leaking there? Mine is leaking as well towards back of engine, but im not sure where it can be leaking from

@PATAN

Love how you don’t show how to take out the hard part that I’m struggling with

I've never seen a video were people say torque specs the intake should be torqued to 89 in lbs in sequence