My E36 coupe gets completely stripped

Подписаться 230 тыс.

Просмотров 35 тыс.

50% 1

we strip the suspension off the e36 coupe
►Shop BQR merch - boqer123.com
►Subscribe to our channel! bit.ly/38sOd5M
------------------------------------------------------
Welcome to my channel Boqer123, aka BQR.... a RU-vid channel based in the UK where we make videos modifying and building cars, track/drifting days & driving, BMX videos and more. You can subscribe here - 👉🏻bit.ly/38sOd5M👈🏻
We also run the clothing company BQR, where we specialize in custom streetwear clothing, accessories, and stickers. Visit our website and grab some stuff - boqer123.com.
Instagram:
► / bqr123
TikTok:
► / boqer123
Twitter:
► / boqer123
Facebook:
► / boqer123

Опубликовано:

8 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 135

@krayonss 2 года назад

excited to see the v8 go in for the last time, when the bloke with the plymouth walked in i thought andy had grown a mullet in between clips to start with

@shawclip43 2 года назад

if you plan to spray the undercoat on use a REALLY wide spray nozzle. makes the job so much easier

@CYMRU619 2 года назад

When I did my E36 I used a wire wheel on the grinder to remove any cracked underseal or rust, treated any rusty areas with bilt hamber deox gel, epoxy primed those parts, scuffed up everything else then a final overcoat with U-Pol raptor (You can tint it to body color, it would look sick in boston green). It's a long and shit job but well worth it especially when the car's already stripped down.

@frankiewalnuts 2 года назад

Just a tip when you use weld through primer when you weld wear a respirator as the zinc in the primer can create toxic gases usually white smoke

@georgeboast9116 2 года назад

I’m actually a welder! Sounds like you had the wire speed to fast for the metal thickness or you were to far away from the metal! Weld towards you so you can do the wire placement, 45 degree angle of the tip, slow and stead does it use your dominant hand to weld and the other hand for support and just slide along the surface! Love you boq !! 😘

@TheSpectre223 2 года назад

Jack might not be loving the Focus but you showed with the Passat that you can take a fairly mundane daily and still make it sick. Chuck some rims and stuff on it, make another little 'Budget Daily' series out of it, keeping it cheap for his sake, and you could make much cooler without losing the practicality.

@sFsxHarri 2 года назад

Just done the same rear subframe on my 46! Such a good feeling looking underneath and seeing loads of new stuff! Also can’t knock Jack’s focus, I used to have one and made it look what i thought was not bad at the time!

@cnvkt 2 года назад

Bro i thought i was going insane at 3:00, its just Andy in the toilet lol

@jus__gra 2 года назад

Was the reinforcement plates home made? Binged the full playlist so far. Got a full notes list of things to do to my 36 now 🤟 Also what kit are you putting on it? Maybe a Don Musk?

@k15DarkKnight 2 года назад

That £2.50 Chineseum chrome socket on the dewalt is naughty

@philipcowans5831 2 года назад

Love the process, it'll give you peace of mind when it's done and driving! Keep the videos coming

@frankiewalnuts 2 года назад

Those pin holes in your welds is called porosity welding its when the gas gets trapped in the weld, it creates weak points in the welds, not good. If you grind it out and redo it in those areas is the only fix some people just weld over them. I think you would get better results from stick welding, especially for thick stuff

@JoeWilson-cw1rt 2 года назад

Clean shroud Clean tip (don’t want to feel the wire in the harness or torch head) Correct LPM of gas flow Clean workpiece Consistent distance from tip to work piece (around 10-12mm) Consistent with travel speed from arc start to finish. When you’re new to welding, whenever you alter your parameters always practice on scrap before. Do a good 4/5 runs, always want to find the travel speed and ensure the parameters are correct.

@MrWardy369 2 года назад

Welding tip, keep doing it, hours count and youre already pretty decent at it 👌🏻, defo get a decent under coating for it

@charliewilton9367 2 года назад

Mig welding is all about being comfortable and keeping the weld pool consistent, before commencing your weld run the torch over where you want to weld and make sure you can get from a point to where you want to be in one smooth and comfortable motion, hope this helps.

@perrysutton5757 2 года назад

This is my plan for my is200! Love that you do your own work too!

@seanh5648 2 года назад

Literally just stripped my rear subframe on my Boston green E36. Need to take it all apart now. Thanks for the bushing tips 👍🏻 Look into the bilt hamber anti corrosion range

@itslukey6135 2 года назад

When re assembling, pop the new bushes in the freezer for an hour beforehand, will help with pressing them in 💪 keep up the great content boss!

@nickrendell4300 2 года назад

Think raptor liner is one that car restorers use, nice little project to get the underside of your e36 looking good.🤘🏻👍🏻🤜🏻

@Smjcko 2 года назад

Whilst it’s stripped get the under side sealed

@shawclip43 2 года назад

did you even watch till the end.... pfff fake fan

@Smjcko 2 года назад

@@shawclip43 it was that last 3 mins

@shawclip43 2 года назад

@@Smjcko exactly, watch the whole video pfff

@koopzz 2 года назад

he also mentioned it in a previous video...

@davog1946 2 года назад

I wouldn’t. Most people do it badly and it’ll just rust between the factory sealant and the crap that gets put on top.

@danwest98 2 года назад

Just finished undercoating my e36 coupe with 4941 dinitrol. Not a fun job but so worth it once its all done.

@creamsoda5492 2 года назад

this looks like SO MUCH WORK! never fails to amaze me how people can tear a car down like this and put it all together in working order. i'd be so paranoid I'd forgotten to fit something or put something in incorrectly. great content as always BQR

@racecarislife1365 2 года назад

Happy to see the 36 back!! I can’t wait to see it all back together!! You lot are monsters

@boqer123 2 года назад

you win the lanyards! Drop us an email - support@boqer123.com

@bs-rz4ny 2 года назад

I was praying you saw that speed sensor before you dropped it, then saw the cable go tight, literally gets me everytime😂🥲

@shaunwelch9176 2 года назад

Degrease all uderneath rust primer then underseal, done that on a 2006 mk2 focus st and still looking fresh now 4 years down the line

@tomca941 2 года назад

I literally ironed one of your T-shirts while watching this 😂😂

@nickg9506 2 года назад

A quick tip for mig welding, I find doing little circles as you’re running the bead helps. Sometimes focusing on trying to be still and running a perfectly straight line can make you more wobbly, doing little circles let’s you just focus on doing circles. And it can look like little tig weld dimes once you get the hang of it

@neonformula9386 2 года назад

For the under spray make it midnight purple looks really nice with the green

@dantregale218 2 года назад

Practice practice practice is all I can say on the welding front and mess about with wire speed to suit you (just not to slow for the power you got) they ain’t the prettiest welds but they’ll serve their purpose, but yeah practice is the main one get loads of scrap and put it in different shapes different thicknesses etc and stick it together! (Then give that as a giveaway at one of your meets as a trophy lol) Top vid though boys, oh and I did I mention practice

@billybishop3864 2 года назад

Got an E36 touring myself and its definitely one of the best cars I've ever owned.

@markandbow5774 2 года назад

ICE blasting to remove the rust and crap, leaving a virgin surfaces to apply under undercoatings like zinc spray, wax oil or even raptor. Great content, keep up the good work !!

@conscars1995 2 года назад

This is my favourite RU-vid series Can’t wait to see this finished 🔥🔥

@jallakongen5339 2 года назад

You need to experiment more with the settings of the machine. I think you might have both wire feed and power to high for that job. Always need to adopt to what you Are welding 😊 Cant wait for the parts to Get freshened up🔥🔥

@robertmellor7059 2 года назад

strip underside to bear metal as best you can (get any old underseal off) then..... one coat primer one coat Corroless Glass Reinforced paint one coat Raptor Bed liner + Dynax S60 sprayed inside the sills & every cavity you can access

@Conjabba 2 года назад

A tip from looking at the welds you maybe need to keep a bit closer with the tip and go a bit slower

@FoxmanI7 2 года назад

Excited to see where this is going maybe spray the underside a lighter colour so if you wanted to do photos or put lights under it would stand out more

@ryantomlinson4367 2 года назад

Welder was set up with too little wire speed volts sounded good just turn the wire up a touch want it sounding like a your frying a egg and nice and smooth . A good technique is called weaving effectively 2steps forward 1 step back. Don’t rush either and the holes in the weld tend to be either oxygen overcoming the argon shielding gas or dirt on the steel just dig in with grinder then go over it. Wen it’s spluttering and making the gun bounce most likely be too far away, too much wire or a bad earth. And remember, “grinder and paint makes me the welder I ain’t”😂

@richardwest7092 2 года назад

welder looked like it was set on to higher power and possibly to much wire speed, all welding is practice though keep up the good content 👍

@MANweldingservices 2 года назад

Little tip for when you're welding if you see loads of little holes in your welds (porosity) grind the weld out and redo it, if you want the weld to be strong. Loving the bm vids

@liamdolly5560 2 года назад

Get the upol weld thru primer it's a lot better also I'm welding 10 years now full time the welding is ok comes with time and u should watch some more video on welding on youtube or ask ur friend that did that nice bit of welding to watch the way u welding he will know what ur doing wrong other than that keep it up class project

@danielparry9900 2 года назад

Tip for undercoating: Make sure it goes on the bottom of the car. Nice to see more progress on the coupe, the barracuda Rick was in was brilliant. Cheers boys

@leonknightley3515 2 года назад

Porosity welds😂 needed to clean the metal more next time

@andrebassila3602 2 года назад

Try dropping the amps a bit on your welding machine, results in less spluttering and cleaner welds. Don't drop it too much, you still need it to penetrate the metal in order to weld properly.

@porshgt3 2 года назад

welding tip, slow as you can, dont rush. Youll get a feel for it and you know when youre going way too low. always push not pull. Get comfy.

@KyushaStyleTuning 2 года назад

Excellent stuff! That big boy DeWalt makes short work of those bolts 😎👍

@TwistedTattoo.WarShorts 2 года назад

Brilliant idea getting the subframe reinforced👍🏴󠁧󠁢󠁷󠁬󠁳󠁿

@austinmitchell2006 2 года назад

I recon you should go for black subframes with white anti roll bars and white accessories bro

@triiks6136 2 года назад

weird that this wasnt in my subscriptions tab, glad i searched the video anyway

@aaronjacob7819 2 года назад

Push the weld pool as your welding with the mig so that your gas is always covering your weld also the more you grind back the weaker your weld so try keep the polishing pads to a minimum

@ADM_K 2 года назад

Andy in the office with the mic on at 2:50 gosh he is so handsome

@EagleEyeTye 2 года назад

Love seeing a boqer video in the sub boxxxxx

@oakesiii3412 2 года назад

I have the same welder as you on that sort of metal id be using no 4 on the voltage and between 3-4 on wire speed, if your right handed steady your right arm with your left hand then flow from one piece of metal to the other they look better than my first welds 😂

@SvenGrube95 2 года назад

Wax oil is what I’ve used on cars in the past, works very well!

@adamjack8095 2 года назад

Use Upol Gravitex undercoat stonechip to do the under side top quality stuff drys really nice and leaves a mint finish 👍👌

@TheGte1981 2 года назад

You will need to put kurust on any rust you can spot before you're ready to prime & under seal to stop it rusting it's proven to stop any further spread of rust. It's the one in the white plastic tub by hammerite 🤟

@huppcio1 2 года назад

Got the socks from You guys must say really comfy ;p Use flap discs on grinder to strip old paint and seal out, prime it with good stuff like buzzweld rust encapsulator and on top of that por15 or other undeseal of Your choice

@markkiely6430 2 года назад

also please buy a TIG welder. MIG welding is all about settings. TIG will teach you how to weld

@Liam-nf5bi 2 года назад

Nothing wrong with those welds Boq, any reinforcement is better than none 👍🏻

@barney1878 2 года назад

Use tetraschutz with an air compressor and the gun u can get for it, it dries in a few hours and gives decent coverage and lasts forever and it aint megabux

@leestirling9286 2 года назад

Buy a good welding helmet i found it hard at start because i couldn't see . I bought a esab sentinel a50 expensive but its unreal .keep up the goid work 👍🏻

@mattypayne5948 2 года назад

Dry Ice blaster 🧊 and a good thick coating of under seal 🦭

@Bennnjio 2 года назад

Love the vids man

@jakeedwards5332 2 года назад

Time to get a hydraulic press maybe ? EBay 12tone done the job for me on pressing bushings and wheel bearings and cost less than 80 quid

@stanleycherrington2950 2 года назад

the only way to get better at welding is by welding. do it as much as possible and you'll get better with experience. Use any advice you can to get the welder sorted out ( IPM etc) and then go from there.

@jamesg1769 2 года назад

Need to clean surfaces of paint and rust before welding with a grinder, will make the welds a lot better

@Jahmed5635 2 года назад

Hammerite underseal is a shout mate

@ad91venture14 2 года назад

Personally I wouldn’t undercoat. I’d wipe it all down with Acetone then spray it with Nyalic Leaves a better finish than the thick under seal shite

@djeriejr3783 Год назад

When welding also mostly focus on the puddle

@robertdam1083 2 года назад

Etch then prime but firstly rust convert the metal

@meister_harris5623 2 года назад

Give us a lanyard and I’ll buy a bmx again after being out for a few years.. been wanting to get back into it for a while now👀

@Brother-Crow 2 года назад

Primer is soluble, it doesn't stop rust.

@minimeakz5615 2 года назад

Do all new brake pipes on it too, the fresh copper pipes will look sick with all the new and fresh powder coated suspension

@luckywilf9204 2 года назад

Just do some skidding with it in the next videos, it already looks mint!

@kmb_964 2 года назад

Can’t wait to see it back on the road

@moritzdo8305 2 года назад

Nice that's the right step!

@LateNightRituals Год назад

Dream build

@georgewilloughby478 2 года назад

Use more shielding gas less rusty welds

@Jordan-xq4bj 2 года назад

What impact gun are you using? Mine has recently gave up the goose and looking for ideas to replace it with

@TheBorstiStyle 2 года назад

@boqer123 Why dont just buy upgraded rollbars than coad them? At least in the front it would be good with the more weight of the v8 or not?

@bonkers0365 2 года назад

Welds aren't thst strong due to lack of gass hence all pinholes in welds, no shielding

@welshadventures7243 2 года назад

Lovely bit of welding that 👌🏻

@bananajuice3143 2 года назад

9:15 & 16:15 unreal how you guys have the same taste in music as I lol

@nathanherity3031 2 года назад

Gangster pat in background

@robertthorgudmarsson4898 2 года назад

The coupe deserves this 100%

@clutchkicksbiketricks8462 2 года назад

are you gonna keep the v8 stock? Bet been watching since early webisode days

@padhraicoboyle7564 2 года назад

Yesss waiting on this

@44ro.n 2 года назад

what colour are you powder coating the parts?

@t.j.dennehy5164 2 года назад

Ambitious but would be nice to have it on the road before end of summer

@joepartington9639 2 года назад

Man this looks so much easier on a lift, stripped the rear of my car down last winter on the driveway 🤣

@taylorvousden 2 года назад

Yes lover Beamer action 👌🔥

@lennart-nohesicrew1523 2 года назад

can i win? put an angle kit + e46 control arms in

@Past_Worlds 2 года назад

I'd watch some videos on how to set up your welder for the purpose you're using it for tbh, once you get it dialed in your welds will be better just for that. EDIT: also just noticed i've been subbed for 10 fucken years on June 24th just gone, what the fuck.