My First Plowing 

Согласен с тобой

У меня трактора тоже 1991 года и выглят как новые, хотя и в работе постоянно

трактор норм только овцы не могут завести!9 надо с места быстрее заведется!

С охотником соглашусь

What county is that? It's wet but not very and no frost.

@@hrz4x4 I'm from Serbia, northern part between Hungary and Romania

Forgot to ask this MTZ which you used for plowing is your third tractor?

Yes. It's my third tractor.

So we can expect new restoration series on your channel :-)

Thanks. Looks like it might just work if I install some new parts on it and learn how to plow (better).

@@hrz4x4one more thing, that this plow has small mold boards, so the working width per furrow is 30cm, if I understand right, but there are bigger mold boards, which, i hope, can be mounted on this plow and then work width will incrase to 35 cm per furrow

@@agrokanals The working width can only be changed by a different beam set up to let each body take more land, as in a vari- width, or of course adding more furrows. A different board type may leave a wider furrow for the tyre but not increase the working width. You both probably know that, but it is a common misconception. Meanwhile continue to have fun farming. Narrow tyres will always make a neater job.

@@warrenblain2365 well, you're right, I was mistaken a little bit about theese mould boards, just because it's my second season plowing, so I excuse for that what I said. But yes, practise makes perfect

Keep on enjoying what you do.

Same here. The first hard work showed the real flaws on the tractor(s). I lost my radiator with the very first hard work etc. But they are workhorses and they should be used on full gas and also on heavy conditions.

Dr. Zoidberg Zdarova

@@dovydasleveris3809 Labas, kas ta zdarova ?

Panasiai kaip labas

@@dovydasleveris3809 Supratau :D Labas :D

Thanks.

M T Z 8 2

Yes. That engine is very good. In full throttle the oil pressure is constantly 3 bar. Unfortunately gearbox needs repairs.

Bellaruss80

Eziz Musayev its a 82 because its 4x4 and we have belarus 1025 turbo, 80uk 80l 52

Very interesting. 4x4 versions are quite expensive then I guess. And you have hi and low gears in transfer box?

The price of the front drive axle with everything needed for the installation is about 1500 euro . Bulgarian "Bolgar TK 80" like transmition is the same like the "MTZ 80" in your video. I do not understand what you think about transfer box. Мaybe I can not properly translate it.

Transfer box is the section before gearbox. Some versions of mtz have hi/lo (rabbit / turtle) gears you can select from there and some countries don't have that selection. Maybe you understand now.

@@hrz4x4 Yes, all of bulgarian "Bolgar" have hi and low gear in the cabs!

Thanks.

Kverneland Hydrein: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KmOnEeG3NwA.html

maybe. or I just knew that it's not top notch and predicted it happening here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-xB3bQyHErjE.html

It's a big problem when you put on bigger and diferent wheels and then sometimes your front axles shaft is destroyed.

Thanks.

Thanks. I agree, the plow needs some attention. But I wanted to have some experience with it before I start fixing and messing around.

Thanks. Yes, that's standard configuration for 80/82. The distributor is connected to the back wall of the hydraulic reservoir under the steering wheel and controls are on the right. You can see see configuration better in this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Xzd5QZsJ4f4.html

Tigu/jänes kang. Poolkäigud ja tavalised pmst.

@@hrz4x4 Aitäh

Yep. They wiggle until you do this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-xB3bQyHErjE.html

Hea teada, et vähemalt ei ole ma üksi esimest korda adraga pusserdades... Kus see öeldud on, et tõmmitsa pikkus peab selline olema? Ma suutsin leida, et tõmmitsad peavad olema ühepikkused, rohkem mitte. Ma ei tea, mis seal esisillas juhtus, parema poole põlves tundub olevat. Ei ole veel lahti lammutanud. Lakkas vedamast ja tegi kolks-kolks. Õnneks liigub ja ei ole ratas plokis.

@@hrz4x4 Mul naabrimees kogenud künnimees ütles, et vasakpoolne tõmmits peab olema 515 mm muidu atra korralikult kündma ei saagi . Ader pidi võimalikult paremale poole jääma. Viimast reguleerimist saab teha parempoolsest püsttõmmitsast keerates kas pikemaks või lühemaks. Seda juba künni käigus.

Ma oletan, et see mõõt vastab siis, kui russiga künda. Aga kõik muu tundub loogiline ja teised kommenteerijad on ka seda öelnud, et võimalikult paremal jne.

@@hrz4x4 Tere! Väga ilus töö, arvestades et maa paistab savine ja raske olema. Püsattõmmitsa pikkus pole oluline, tähtis on et adra raam oleks maaga paraleelne, see tähendab et esimene ja viimane hõlm künnaksid ühe sügavusega. Kurekaelad peavad olema maaga risti. Lõpmatult paremale sahka ajada ei ei saa, sest esimene korpus peab kündma sama laia maa kui teine korpus. Kangist saad muuta adra töölaiust, kui on kerge liivane maa, lased saha karemaa poole, kui savine raske siis künnimaa poole viilu kitsamaks kõikidel korpustel, sellega tagad et künniviilud ei lükka sahka liialt vasakule. Muidugi vanematel korpustel on vastusurve plaat väga lühike, uuematel poole pikem. Veovõllil selleks vänt sees. Kui traktoril liiga laiad rehvid, mis ei mahu künnivao sisse, trambitakse viimane künniviil kokku ja siis ei saagi esimene korpus seda täis künda. Kverleland adrad on parimad. Muidugi ideaalis kui kõik on õieti timmitud, peaks traktor jooksma otse, esirattaid pole vaja keerata vastu vagu ja tagumised külgtõmmitsad on vabad ehk ilma pingeta künni ajal. Jõudu!

​@@jurih5622 Tänan abiks info eest! Mul on kogemused väga väikesed kündmisega ja selle konkreetse künnitöö suurimaks miinuseks oli adra halb seis. Peale kündmist sai päris palju juppe ära vahetada, mis olid juba ammu liiga kulunud. Parandamise video on siin: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KmOnEeG3NwA.html

I don't know yet. Just took the other tractor and finished the job. I can still drive it but I hear some clonk-clonk in the right side knee joint.. It's going to be another part of the restoration videos :)

@@hrz4x4 Probably broked those teeth of the axle. Here is the example of the axle-- www.traktors24.lv/lv/Catalog/PrieksejaisTilts/VelkoshaisTilts/Product/2089 These are the weakest places of the whole front axle.

Probably. The knee joint was quite bad anyway and needed my attention. The other side has been open and repaired (by the previous owner). ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-xB3bQyHErjE.html

I honestly did not think anything about this plow before I had plowed some hectares and started to figure what the brand and maker was. It was a surprise for me also :)

Depends the field was very bumpy and plowing height is also very varying. I did not want to make it too deep. Mostly around 15-17 cm I would guess.

в основном 2 передачи, 3 передачи не работают, иногда 4 полуприцепа

@@hrz4x4 следуюший раз второй трактор 9 скорость включите быстро заводиться

looks like camera tripod. just a guess.

yes. it's a camera tripod (which I never used during this video)..

@@hattifattener1 I thought its some sort of hydraulic control unit 😂😂

Thanks. Well it's true that I watched a lot of plowing videos after first day on the field.. Then I leaned how to adjust the plow and how to plow - but it's all theoretical I need some practice now. The videos come as they are filmed. I usually don't want to make them too long so the viewers don't get bored. You think they should be longer?

Absolutly. especially when its sometime new on your channel. I really doubt any of your subber would be bored when you make them longer by this kind of cool new content 😉👍

It's always good to be in the tractor and see the ground turning over.. And I am not doing this with a shovel or behind a horse - great.

@@hrz4x4 yeap

I don't know. They are both around 30-35 years old.

Count on that MTZ was built tractors with small cabins until middle /end of '80, so from end of '80 beggining of '90 MTZ has made changes in tractor appearance and start to build in the big square cabins.

Ok thanks for the information

Thanks. Unfortunately not. But I know how to use a translator :)

@@hrz4x4 😂

Kverneland Hydrein MI

@@hrz4x4 у вас угол атаки как у плн3-35 или долоты по другому стоят?

@@АзаматТентиев Я не знаю.

Great. And are you happy with that plow?

@@hrz4x4 We've had problems with not actually turning the soil sometimes.

You used valtra to tow that? I am trying to compare tractors as I struggled a bit with narrow tires not delivering enough power to the ground.

:-) spring time job. I could not get the 'small stone' with this front loader - better do it in the spring.

Бред)))) люди доп грузы вешают.

@@user-ow7oe7to3f откуда ты знаешь а? знаешь какая нагрузка на передок?

Денис Комаров я тебе ещё раз говорю что до 500 кг вперёд груз устанавливают при пахоте дабы разгрузить задний мост.

@@user-ow7oe7to3f я хз первый раз слышу такое

@@user-ow7oe7to3f но если у тебя много бабок то до тонны можешь загружать

Podlaski Farmer TV