My Mercedes M111 Turbo Engine Built for my W202 Race Car

Просмотров 6 тыс.

% 153

In this video I show you my Mercedes M111 turbo engine built for my W202 race car which formerly had an OM605 superturbodiesel engine. I talk about the special crankshaft, steel rods, forged M104 3,6l pistons, main and cylinder head studs by ARP and other modifications I did to make that engine ready for high boost.
Check me out on Instagram:
w202_performance
w202.store
Check me out online:
czsmotorsport.de/
w202.store/
Check me out on Facebook:
Fundametrik

Авто/Мото

Опубликовано:

30 сен 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@nadir3556 9 месяцев назад

I think It Will make an Easy 500hp even more

@OctavChelaru 5 месяцев назад

Torque Monster in the making. Best of luck with the build! If you have a chance, please weigh the engine once built, it's hard to find reliable weight figures for them.

@gwagenadventure727 9 месяцев назад

Love the content keep it coming.

@BoostWorx 8 месяцев назад

Great work pal

@tobiasspielbauer4835 8 месяцев назад

Nice build👍 Have you done any modifications in the oil-sump itself for high cornering speeds?

@FineW_TurboM111 9 месяцев назад

I need to know what engine mounts those are, very curious 🤔

@nabarl3023 9 месяцев назад

Sick!

@JDMCARSCIVIC 5 месяцев назад

Is the crankshaft much heavier that the original? What the advantage of having the extra counterweight?

@nikadimchenko4702 7 месяцев назад

Where can I find such forged pistons ?

@medievilassassin 9 месяцев назад

Great work mate , did you also put wedges in the block between the pistons? Also what engine mounts are those? With that amount of horse power will you have issues with the prop shaft and differential? Also what gear box are you using for this application?

@incolink 9 месяцев назад

between the bores... good question

@brucemclaren- 5 месяцев назад

Hey bra i'm looking to fit an aftermarket throttle position sensor to a 97-98 m111 engine. How do i go about it. I've been thinking of modifying that rocker thing on the gas pedal mechanism would that provide enough voltage range to work with?

@junkyarddawgfixit8970 9 месяцев назад

Everything is looking good on that engine, just wondering what the static compression ratio is and if you have to align-hone the main bearing bores of the block after you install that main stud kit. Keep rolling.....

@CZSMotorsport 9 месяцев назад

Hi, I checked the deformation in the main bearings with the stud kit. Measured it before and after. It gets a slight ovality but all within the acceptable tolerances. Bearing clearance was perfect. Some people say the ovality can help by providing some kind of oil wedge that helps with lubrication.

@junkyarddawgfixit8970 9 месяцев назад

OK, When I put the ARP main studs into my 2.8 VR6 I first assembled the main caps with the factory TTY bolts but only tightened to the initial torque, then I installed the ARP studs, hand tight to the block, one at a time, and torque the nuts to the same intial torque, after they are all installed then tightened them in sequence to the ARP torque value on the tech sheet. I did the same thing with the ARP connecting rod bolts for the factory rods. The idea is to let the factory bolts align the caps, and by removing them and replacing them one at a time, it will maintain the alignment. And by installing the studs into the block hand tight only, you will not expand the main saddles around the bolt holes which can cause ovality.@@CZSMotorsport