Neodymium vs Ferrite Titanium vs Phenolic Comparison for COMPRESSION DRIVERS aka HORNS! PRV Audio

Подписаться 3 тыс.

Просмотров 15 тыс.

50% 1

In this video learn the difference between a neo and ferrite driver. Which is better? Well that depends on your application, and budget.
The second part of the video is the difference between TI Titanium and PH Phenolic drivers.
In this video I use the following products to show you:
PRV Audio
WGP14-50 Chrome Silver
D3220Ti
D3220Ti-Nd
D3220Ph-Nd
Similar products:
WG2500Ti D280Ti D230Ti
D4500Ph D3220Ph D2200Ph D270Ph D275Ph D175Ph-S
JBL 405 TRIO

Опубликовано:

28 сен 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 38

@headhoncho4890 Год назад

Very informative I’ve been in car audio for 30 years and always wondered about this thanks

@12voltfever Год назад

Thanks man I'm glad I could share and teach a veteran in this game something new !

@dandesouto6076 Год назад

That’s exactly the video I was looking for now I know very well which one I want after your explanation.

@mr.mosley7196 9 месяцев назад

So which one is best my guy??

@12voltfever 9 месяцев назад

@@mr.mosley7196 there is no which one is best. It depends on your application.

@djsourabh1366 Год назад

Thanks 😊

@scottouimet2865 Год назад

Ty, so if I was using some say 6.5" prv bullet mids and 4" ti700 tweeter wouldn't need one of these or would my sound gain a lot from adding a ti horn? Sorry if that's not asked right. I know a lot about the bass side of audio not a lot about mids/highs and crossovers. But I'm planning a large build and need to get my mids and highs up to sound right. Thanks you and subscribed

@12voltfever Год назад

Sorry for the late reply, you can always benefit from a compression driver for a more full sound. With a phenolic driver (1" would be sufficient such as the d270ph) you can run the low pass lower on the speaker so the vocals are stronger and then the driver will fill the gap between the speaker and the tweeters!

@nikkyng8141 Год назад

I have 4 10mb800ft per rear door 2 2200ph per 2 tw500my per 2 st200 per What frequency would cross them at for my application

@12voltfever Год назад

In your case for the D2200PH with supporting tweeters, depending on power of course, you can run them 600bt18-5000bt18 (them TW500 play pretty low for a tweeter). Run them 10s low on the LPF (between 1650-2200 on the low pass) let the driver do the upper vocals and the midbass will shine on the lows and low vocals!

@mr.mosley7196 9 месяцев назад

Im running (6) 6.5 neos in my front doors with 4 tweeters and gonna add in 2 horns in each door off of their own amp. Would phenolic be the best way to go?

@12voltfever 9 месяцев назад

Phenolic would be good. I would take a look at the new PRV WG175PY or if you have the space WG270PH

@samsmith977 8 месяцев назад

Could you compare a bolt-on vs screw-on horn driver of the same watt and size?

@12voltfever 8 месяцев назад

There is no difference. Only the way the waveguide mounts

@samsmith977 8 месяцев назад

@@12voltfever Thank you for the quick response. Thanks.

@shadrackrolle8461 Год назад

Can they need you on a professional dj sound system?

@12voltfever Год назад

Don't really understand the question?

@Bigpaul12345678 8 месяцев назад

When using Titanium driver do I still need tweeter ?

@12voltfever 8 месяцев назад

You don't need it. Some people will tell you otherwise. You can use a tweeter also and it does improve brightness.

@Bigpaul12345678 8 месяцев назад

@@12voltfever thanks I have been using both and I removed the tweeter and my sounds better with out them

@AllSoWavyReese Год назад

So the titanium is higher and the phenolic is adjustable mid range type?

@12voltfever Год назад

They both play "mid range" frequency but the titanium can play much higher, but not as low as a phenolic.

@AllSoWavyReese Год назад

@@12voltfever i have 2 4” titanium tweeters and 2 2” titanium tweeters with 4 neo 8’s mid. I think imma go with a phenolic and tune a little higher

@AllSoWavyReese Год назад

@@12voltfever do horn length play a part?

@12voltfever Год назад

@@AllSoWavyReese yes especially on phenolic. The longer the better. Sounds cleaner and gives deeper vocals.

@AllSoWavyReese Год назад

@@12voltfever hey thats wat he said but ok i got u😂

@austinhenry8814 5 месяцев назад

So basically have one of each a ti/ph a good mid range and go to work

@12voltfever 5 месяцев назад

Yes it's good to combine them

@rcfaudioitalia6110 10 месяцев назад

titanium is better. most of c.drivers use titanium.

@12voltfever 10 месяцев назад

It is a matter of preference, depending on the system.

@rcfaudioitalia6110 10 месяцев назад

@@12voltfever I know. I have titanium, polyester, polyimide. All 3 have their caracteristics.

@MegaJohn334 2 месяца назад

What would u say is better? I have B&C MH32 12”, and Prv tweeters, I want to get 4 drivers. What would u say is good to fill in the gap? Phenolic or titanium? What brand ? Thank you

@rcfaudioitalia6110 2 месяца назад

@@MegaJohn334 MH32 won't couple well with a 4" c.driver. You are going to have missmatch on 2000hz. I'd sugest you DE250 that produces crystal highs. I use it on ME45 horn. Try it. You'r gonna ❤️ it.