Nitro Dave Talks About the Nitrous Outlet WinMax TPS and RPM Activated Window Switch! 

Thanks for the feedback! PS. 13b with stinger is pretty awesome!!.

We must know more, email us at marketing@nitrousoutlet.com

Nitrous Outlet Will do any new plates or products for 2018 ? Happy New Years

The WinMax cannot control timing, just send a signal to a timing control box to tell it when to activate the ignition step retard

Yes, it can be used on motorcycles, but the box is not weatherproof.

That is certainly a low voltage for WOT on a gen3 LS TPS sensor, but as long as it is consistent, it is perfectly fine to use that signal. You may trace the wire that the TPS wire on the Winmax is connected to, and make sure it is on either the purple or green wire on the TPS sensor harness.

Our current eta is he end of September!

good question.I also want to know answer

I can’t lock mine out for some reason, I need help

The Gear Lockout feature is looking for a maximum RPM and a minimum RPM drop. For instance, lets say you set a 5500 shift point with a 500rpm drop. The controller will have to see at least 5500rpm followed by at least a 500rpm drop before it will engage the nitrous on a 1 gear lock out. So in your case, youd want to set it at about 100 rpm drop if you wanted it to work. My question is - what trans/ratios you running to get only a 100rpm drop?!?!?!

Nitrous Outlet it's a built 700r4 with a low first gear. The car only has 3.73 gear

You pretty much got it! Our Stage 3 accessory pack would be a great addition to your system as well.

Just as good as EFI! It can also be triggered by WOT switch

@@joshyeater3285 You can select TPS or WOT switch. If using a properly adjusted WOT switch, if you pedal or let off, the nitrous will disengage.

Nitrous Outlet if you use it with a wot switch how would you launch on the tb ? If you floor it it would activate it

When going with the WinMax, there is no need to utilize the WOT microswitch included with the X-Series system. Please let us know if you have any other questions!

Perfect. That is all i needed to know! Thanks for the quick reply!

The WInMax will not, but our ProMax will. www.nitrousoutlet.com/promax-dual-channel-progressive-controller-controller-and-screen.html

Check out our ProMax - nitrousoutlet.com/c-1390660-electronics-ignition-progressive-controllers.html

Thats what i want to no Will this controller pull the timing or do u need to get some other bits

Send it!

SHOE GOD 23 that I would like to see as well

You need to take a look at our ProMax! Progressive control, RPM window switch, TPS activation, gear lockouts and a WHOLE LOT MORE! www.nitrousoutlet.com/electronics-ignition/progressive-controllers.html

Thats what i need to no as thats what i need to do .

Mini on nitrous 105BHP to 205BHP any one find out ?

@@santivr6576 no i think u need a msd6 box and controller. But I pulled the timing by tricking my air intake sencer so when i flip the switch it think it's at -140 degrees and pulls about 4 degrees of timing. There r way to pull timing when u want it to .

No

Yes sir, it sure does

@@NitrousOutlet man that was a quick reply! thank you!

It will trigger an external timing control such as an LNC box or MSD Grid

Marco, please reach out to one of our experienced techs at 254-848-4300 and select option 1. We will get you fixed up!

You ever get this figured out? I was getting that same TPS error code before I switched to the blue wire on the TPS for tapping into. Now at idle for some odd reason my Winmax is reading the TPS percentage backwards from 100% and on down. Then I noticed at idle the Winmax was reading 3450 to 3700 at idle while my factory tach was reading 850 to 900. Not sure if I need to change the cylinders to 4 instead of 8 like other window switches I have used in the past. 2002 C5Z FBO, TSP 233/239 112 lsa cam and Nitrous Outlet plate system wet kit, Winmax, LNC 2000 etc.

Yes it will work with a WOT switch, but a WOT switch is not needed if your vehicle has a TPS as the WinMax taps in to the TPS.

Nitrous Outlet awesome! I’m trying to figure out exactly how I want to set up everything and what products to buy so I appreciate the help.

@@jl8973 no problem!

Its a bit of a workaround, but it is doable. You'd program the WinMax as RPM only. On the stage 1 output, it would power a relay that allowed power to the Zex box. That way power would only be applied to the Zex box within the given RPM range and the Zex box would still activate via TPS.

Nitrous Outlet what about gear lockout?

Yes, gear lockout would still work in RPM only mode.

Nitrous Outlet hi could u email me a diagram of how to wire in the tbrake interup relay into this system using only 1 stage. bnastystuntz@gmail . com thank u

That’s the whole point of a window switch.. it doesn’t energize the solenoids until it reaches a certain RPM- set “on” to 3500rpm or 250rpm above what you launch at, whichever is greater