Nitrous Express - Maximizer EZ Progressive Controller Part No. 16006

Подписаться 10 тыс.

Просмотров 21 тыс.

50% 1

Part# 16006
Announcing the best value and easiest installed nitrous controller ever produced!!! The NX Maximizer EZ Progressive Nitrous Controller smoothly ramps in your nitrous system resulting in increased traction and less strain on your vehicles drivetrain. Ramp time is adjustable from 0 to 4.5 seconds via a simple rotary knob (no laptops required). Easy 1 minute install - Plugs directly into your existing nitrous system relay harness eliminating the need to splice wires.

Опубликовано:

28 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 31

@dustinwalker8576 5 лет назад

How does this work with a window switch that turns off the nitrous between shifts? Will it continue the ramp regardless of shut off time in between the gears ( automatic, nitrous outlet winmax)

@NitrousExpressVids 5 лет назад

It would restart the ramp anytime you went outside the "rpm window" on your window switch.

@ldogg509 4 года назад

It is NO GOOD FOR A MANUAL TRANS it rests every time you let of wot! THEY DON'T TELL YOU THAT in any of there videos or instruction. Customer serves was terrible.

@dj4monie 4 года назад

Why aren't you flat-foot shifting? Almost any modern car either stock or with a flash will let you do that.

@ashburnkenneth3625 5 лет назад

How would I use this if there’s no relay box if I have the solenoid wired straight to the WOT switch

@NitrousExpressVids 5 лет назад

you will need to add a relay harness for the Maximizer EZ to plug in to, here is a link to the harness you would need to add. www.nitrousexpress.com/relay-wiring-harness-only-5-wire-15525.asp

@glass2271 2 года назад

@@NitrousExpressVids is there any video describing how this is installed?

@NitrousExpressVids 2 года назад

@@glass2271 The installation of this controller is in this video. 1:20 is the time installation starts.

@billbraski2175 3 года назад

What's recomended return or dead head regulator?

@NitrousExpressVids 3 года назад

It is really dependent on your setup. Its not uncommon for carb applications to run a dead head setup and a return style on EFI.

@mustangjoe2066 4 года назад

This will work with a zex wet tps activation nitrous box?

@daviddeguire734 Год назад

after the ramp time, can you adjust the percentage time on how long it stays on at 100% or does it go off with micro switch?. I know it will from go from 20% to 100% in the ramp time of up to 4.5 but will it stay on till micro switch is left off and will it stay at 100 if I restart all over at 20 with the re amp. Is there a way to turn that off if it starts over half way down the track. Like it to come back on at 100 % if I get back in it.

@NitrousExpressVids Год назад

The Max EZ is activated by the micro switch. If your micro switch shuts off, nitrous flow shuts off as well. If you get back on it mid track the nitrous will follow the ramp time set by the Max EZ.

@redbaron2448 4 года назад

But doesn't the relay turn on everything? If I unplug my relay and plug this in how will it work without my orginal relay?

@NitrousExpressVids 4 года назад

It replaces the relay in the system and has a timer built within it.

@redbaron2448 4 года назад

@@NitrousExpressVids ok great, thank you

@alliecatcustoms5808 3 года назад

I’m running a NX mainline kit on my c10 with a 454, and I’m also running the additional trans brake interrupt relay in addition to the regular NX relay. Will this controller just replace the nitrous relay and work properly?

@NitrousExpressVids 3 года назад

That's correct it will work like that.

@ltracing07 4 года назад

How does this work on auto trans and a button instead of window switch

@NitrousExpressVids 4 года назад

It will do its usual ramp while you press the button until it goes to 100% then it will stay there until you let off the button. If you get off the button and back on it the ramp will restart.

@acidfly1 5 лет назад

I'm running a Holly Sniper that can control nitrous, with this work with it? @nitrousexpressvids

@NitrousExpressVids 4 года назад

As long as your Holley EFI system has a nitrous output wire you could use that to trigger the max EZ

@torktech9398 6 лет назад

This item is an add on to a window switch so it can be controlled at what rpms to turn on and off at ? great for drag racing and can be switched to full hit during roll racing by turning the nob ?

@NitrousExpressVids 5 лет назад

Yes you can use the Maximizer EZ along with a window switch!

@williamlopez4934 5 лет назад

will this work on the wet shot? I'm assuming this goes to 0 to 100% ramp. it's just the time u wana go to 100%

@NitrousExpressVids 5 лет назад

Yes it will but it only designed to control a system up to 40amps.

@williamlopez4934 5 лет назад

Ok thanks.

@anytakers 6 лет назад

Is this like a digiset or a progressive? Is there a way to adjust ramp time and percentage?

@NitrousExpressVids 6 лет назад

As stated in the video, it is a progressive. Ramp begins at 20% & progresses to 100% based in the time set via the knob on the module. Can be set up to 4.5 seconds in half second increments.

@samuelchan9501 5 лет назад

@@NitrousExpressVids so when you say 4.5 seconds, do you mean it will take 4.5 seconds under WOT to reach 100% nitrous shot? So I can start at a 50 shot and ramp it up to 150 shot?

@NitrousExpressVids 5 лет назад

@@samuelchan9501 That is correct except you would have your jetting in for a 150 shot. Once you hit WOT you will be at 20% of your 150, so about a 30 shot then over .5 to 4.5 seconds it will ramp to that full 150 shot.