NT Carburetor upgrade | 60 mm air filter!

Подписаться 369

Просмотров 9 тыс.

50% 1

Here I customized my NT carburetor for a motorized bike.
The stock intake leaked, didn't allow much air through, and didn't look good.
Thanks for watching.
DISCLAIMER:
Crankshaft garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Crankshaft garage recommends safe practices when working with power tools, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Crankshaft garage. This video is for intended for entertainment purposes only.

Опубликовано:

2 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@dustinh4175 2 года назад

You replaced the air box not the intake. And all you have to do is drill some holes in the old one and it'll flow fine

@chaunceyhulbert7264 5 лет назад

In my opinion those old carbs are a lot better. I bought a new one and have had nothing but trouble. I dealt with constant vacume leaks and only got it working tonight.

@unknown-pl7pg 2 года назад

If I use a 50mm air filter will it fit with out cutting up the old one

@foxman362 5 лет назад

you should lazer print these parts sell them on ebay.com

@foxman362 5 лет назад

5:03 is that jb weld?

@mastermind3565 5 лет назад

Is the 60mm the air cone filter rubber fitting that goes around the stock air filter

@crankshaftgarage5722 5 лет назад

Your exactly right, it is. Thank you for your comment.

@jonathanwilson1380 3 года назад

i actually just 3d printed a bracket

@stephenbarry8973 5 лет назад

Can i ask why u put sealant on the old part of air filter when u scew it to the carb before u fit the new filter ?

@crankshaftgarage5722 5 лет назад

It had gaps around it which can let in dirt and sand.

@stephenbarry8973 5 лет назад

@@crankshaftgarage5722 I see , have any issues with the new filter ,as I saw I few vid where people say after installing the rc carb filter it ran to rich ,carb not being able to breath well due to the filter matiral ?

@stephenbarry8973 5 лет назад

@@crankshaftgarage5722 Im not really that technically minded , just learning from these videos ,saw I bloke on here who was tinkering with the idea , be interesting to see what happens lol

@dangerousdoggo5465 5 лет назад

@@crankshaftgarage5722 Supercharging a 2 stroke???? What are you even talking about? You need to read up on 2 stroke engines... Go read a book!

@eduardodiaz5762 4 года назад

@@dangerousdoggo5465 you technically can supercharged a 2 Stroke, as for turbo it is also possible. It's possible, doesn't mean it would require alot of work, hard determination, and knowledge. But it is possible

@foxman362 5 лет назад

you should sell these mods on ebay.

@integrationofmanandmachine4714 4 года назад

Filter replacement won't get power. Only good looking.

@greenmachine55 4 года назад

Furkan Yıldırım_Pro it was never about power it was improving its running power your engine runs more efficiently when it can breathe better and get a better mix of air to fuel mixture

@akirakurusu6623 4 года назад

@@greenmachine55 that may be true but honestly it made my bike slower....

@connorssmallengines6663 4 года назад

If you adjust your mix right too add more fuel than you do with the stock filter you should get more low and higher end torque

@Miklalo 5 лет назад

What is your jet needle setup? Are you at the top or the middle or the bottom?

@crankshaftgarage5722 5 лет назад

the jet needle is at the bottom, the throttle cable comes in at the top. if you mean the e-clip on the jet, it is at the middle setting. but the best setting for it depends on your altitude.

@integrationofmanandmachine4714 4 года назад

I use .60 jet

@stevensabol1281 4 года назад

Furkan Yıldırım_Pro what’s the default jet?

@prodbyred7693 5 лет назад

have you noticed a difference?

@crankshaftgarage5722 5 лет назад

Well the main reason a did this is to protect the engine from dirt and sand being sucked into the combustion chamber ( their where gaps in the old filter) and to make it easy to clean. I've been busy and had to put the project on hold and I haven't been able to test it yet, but when I do (hopefully soon) I will post updates on it. Thank you for watching!

@dangerousdoggo5465 5 лет назад

@@crankshaftgarage5722 Lol the other filter protects more than this mesh one. the gas on the sponge is good because it stops dust....

@integrationofmanandmachine4714 4 года назад

This wont get you any power.