PLA Acetone Vapor Smoothing, it works! comparing 6 brands and results.

Подписаться 13 тыс.

Просмотров 56 тыс.

50% 1

"HERECY!!! PLA DOESNT REACT TO ACETONE!"
well, i will show you differently :P
In this video i show you the end result method of my experiments on smoothing PLA prints with acetone.
Yes you will need some extra equipment for this alongside your safety gear but i really hate sanding so lets go!
0:00 - intro
1:17 - why vapor smooth
1:33 - what pla's used?
2:55 - test model used
3:24 - equipment needed
4:23 - SAFETY GEAR, IMPORTANT!
4:53 - How does it work? the method itself
6:35 - fingernail test on smoothed vs unsmoothed
7:07 - comparing the pla's and their reaction
9:46 - spray putty and light sanding additional tests
11:36 - all models under a macro lens for close inspection
15:04 - conclusion
15:26 - results on a fully finished prop
16:01 - 10k subs, next video subject, outro
INDUCTION heater i used "HENDI 3500 D"
EU:
www.amazon.de/Hendi-239711-35...
Cheaper induction heaters usually only go to 1800 watts, which is still fine, it will just take a little longer for the acetone to warm up.
example link:
USA:
www.amazon.com/Duxtop-1800-Wa...
Use only induction heaters! do NOT use gas stove tops or electric stove tops!
Acetone is extremely flammable so no open flames or glowing hot objects!
Use a stainless steel pot fitted for induction heater use:
EU:
www.amazon.de/SSW-Edelstahl-K...
USA:
www.amazon.com/LARGE-ECOLOGIC...
Cosplay smoke and Thruster available here:
waynesworkshopcosplay.com/cat...
#3dprint #acetone #vaporsmooth

Хобби

Опубликовано:

1 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 79

@saffronproductions 4 года назад

Great to see you back making videos! I only use esun PLA+. I found it sands great straight off the bed with some 180 grit. Easiest PLA to sand by far.

@VideoCesar07 3 года назад

I bought a roll of eSun PLA+ despite the reviews being pretty divided but, I saw that most of the people who had problems just put very basic reviews with no details such as "This filament sucks" "Terrible filament", etc. No mention of their settings, printer , etc. All the ones who had success usually included those details. Took me a big to get the settings dialed in for retraction to remove all stringing but once everything is set it prints really well.

@magicgundam 3 года назад

My experience with esun PLA+ has been that it clogs nozzles frequently, and I've run it everywhere from 185c to 210c. Stopped using it for this reason, but it did produce good quality prints otherwise.

@shaunbennett2910 2 года назад

I run Esun PLA+ without issues in my ender v2 and aquila vox machines. it can be tempermental some times but I find that running it a bit hotter works well...220c-235c 2.5mm retract dis and 25mms retract speed. Also Durcmic PLA+ is one that that works really well consistantly. I have had maybe 3 spools of Esun out of 100 that really were just terrible and I contacted them on amazon and told them and they sent replacements without a return or refund processed...they just sent new roll for the one that failed, which was cool of them.

@healingsounds9960 3 года назад

Very good video m8, greedings from Greece.

@Mintheoho 2 года назад

Do you think the colour in the PLA has anything to do with the effectiveness of the vapour treatment? I noticed it worked quite well on the lighter colours and not so good on the darker. Or maybe just coincidence? 😊

@crash02 2 года назад

Hey! What spray putty are you using for this test? Thank you!

@KonjikiKonjiki 3 года назад

Thanks so much for sharing your results here!! My bf has an Anycubic Mega 3D printer that has been a lot of fun so far. :) I originally came to your channel to find your vid on the Meme Couch model you made for Simon Toeskin, but no luck, and Ken did not post a link. If you could point me in the right direction, I'd really appreciate it!

@WaynesWorkshop 3 года назад

haha well that video i posted to his subreddit, its just a quick timelapse though, the same one he showed but they cut it up in editing for their videos sake

@Dishyg 4 года назад

Does the pla remain flexible and soft?

@farida7777777 3 года назад

Thanks buddy.

@noahsardjan1471 2 года назад

Lekker bezig man,

@MagoMakes 3 года назад

Great vid, fella. Could you advise me on some specifics? What Watt is your induction plate? What temperature is "high" on the plate? What temperature is "low"? Do you think it varies with pot size (I'm likely going to buy a smaller plate and pot)?

@WaynesWorkshop 3 года назад

it goes to 3200 watts, but that high is not needed to get the vapor to go, best is to test it with your small induction plate. wear your safety gear, and test with small amounts

@MagoMakes 3 года назад

@@WaynesWorkshop Cheers, chap. Now to try and find a small, tall induction pot!

@julianheller9832 3 года назад

Hi, thanks for the video. What filament did you use for the shotgun?

@WaynesWorkshop 3 года назад

that would be the " devil design" filament

@lynxshd 3 года назад

Sweet thanks

@DieEneGuyJeWeetWelWelke 4 года назад

Tinytronics for the win :D

@Cloakfiend 3 года назад

I've been brushing and dunking my pla prints in acetone for over 5 years and find colorfabb pla/pha to work well. Ive done many video on this as well!!

@WaynesWorkshop 3 года назад

I've heard indeed that colorfabb reacts great to it, thanks for confirming

@Mech.E 3 месяца назад

Someone mentioned PLA that has been aceton smoothed will crack overtime. Did you experience this?

@Cloakfiend 3 месяца назад

@@Mech.E depends for how long. If younoverdo it.yes, but i have prints that are.over 7 yeara ols and still not split or cracked. If you print hollow Do Not allow and acetone inside or else it WILL split.

@Mech.E 3 месяца назад

@@Cloakfiend appreciate the answer. Good info!

@weld4200 Месяц назад

Polymaker pla plus works way better

@ahmedzubairsheikh 2 года назад

informative!

@dnkeyhnter690 3 года назад

That gun looked really nice

@GraceT 3 года назад

I love ABS, my only issue with it is that they don't come in a ton of really fun colors like PLA. I don't use a heated bed either, just painters tape on the bed and temps at 220-225. But my PLA prints end up looking rough at the end, while my ABS ones look so cool

@WaynesWorkshop 3 года назад

i used to print with abs but my room here was just getting cramped with the enclosure, we move into a big shop space in may, perhaps im going back to abs then aswell as the method in the video here also works very great on abs

@andrearodriguez1839 3 года назад

hello! can i do this but with any PLA filament or has to be that brand?

@WaynesWorkshop 3 года назад

"that" brand? i use 6 different ones... like i say in the video i cant be sure of any/all brands of PLA, testing 6 brands was enough for me to make a best guess :)

@SCHNIERElektrostatik 8 месяцев назад

Have you ever tried to flock your parts after printing? You will get a smooth velvet like surface.

@markusmaurette8992 3 года назад

Was the Ultimaker White PLA the regular or the tough?

@WaynesWorkshop 3 года назад

Regular

@grzbiet 3 года назад

I'm missing the safety gear, and no chance I'll try this inside, so: will heating acetone in microwave work? would it give us more control over amount of acetone and vapours? or would it be just as it sounds: dangerous stupid idea

@WaynesWorkshop 3 года назад

I think the latter... Espcially when not owning the safety gear either way

@Eugensdiet 3 года назад

First time I watched your channel Good video. How come you sound like an American. Looking forward to watching more of your videos.

@WaynesWorkshop 3 года назад

Too many cartoons as a kid, I pick up languages and accents really easy 😁

@IDCrish 3 года назад

Hi, can you come up with any other way of heating the acetone?

@trixiestterror 3 года назад

Have you ever inspected your smoothed surfaces with a microscope?

@WaynesWorkshop 3 года назад

i have not, i can get acces to one though, intresting idea, thanks!

@Moxzot 3 года назад

Pla has different variances of pureness, impure pla will be more likely to be effected than pure pla and I'm sure the heat is also affecting the process. As shown in your testing some had little to no effect.

@WaynesWorkshop 3 года назад

True, however alot of hobbyists will go for the cheaper stuff though, i want to do a round 2 but under a big microscope, and also add abs to lot and compare the surfaces

@user-uo1yn4se8r Год назад

it would probably work best on clear (pure) PLA

@jaysoncummins8197 9 месяцев назад

so, you're ensuring the acetone vapor line is at the top of the print? You don't put a lid over the top of it and leave a little slit for it to ventilate?

@WaynesWorkshop 9 месяцев назад

when setting it from high to low like i did, there is no need for a lid, you can ofcoarse, but remove the lid slowly, otherwise you suck the vapor out of the pot as you lift the lid. drag is a thing so consider that.

@jaysoncummins8197 9 месяцев назад

@@WaynesWorkshop , ok I just thought the lid help the vapor creep up to the height you need it to be to encompass the entire print

@spiritburners Год назад

boy i am so glad you cut to the mask at that point !!! This is so effing dangerous man in both fumes and the explosion risk.....

@No1sonuk 3 года назад

If your induction heater isn't an electric heater, how does it work without electricity?

@AAMovieStudios 3 года назад

It plugs into the an outlet just like an electric portable cooktop with the coil but with induction instead. Have to use steel pots, aluminum will not work.

@No1sonuk 3 года назад

@@AAMovieStudios Oh. So it IS an electric heater...

@BossmodePictures 3 года назад

@@No1sonuk Technically, the "iduction heater" is not a heater by itself as it does not generate heat but only a rapidly changing magnetic field. The combination of the induction generator and a ferromagnetic object on top (like a pot) could be considered as a heater :-D

@WaynesWorkshop 3 года назад

@@BossmodePictures thanks for answering that for me :D wanted to get to this comment all week but didnt have the time and forgot :P

@WaynesWorkshop 3 года назад

the answer is down here perfectly, i will add that what i ment with "normal electric heater" are those small camping hot tops, basicly those heat/glow up with a big ass coil, so thats a big glowing hot object, and thats a no no for this.

@zahari_s_stoyanov 3 года назад

Are these still spongy?

@WaynesWorkshop 3 года назад

@TimoWestenfelder 3 года назад

Standart PLA Filament?

@WaynesWorkshop 3 года назад

ive tried 6 different brands, i guess some can be considered "standard"

@majinkeyboards 3 года назад

4:55 start

@mandoreforger6999 3 года назад

Is it the acetone, or just the heated vapor?

@WaynesWorkshop 3 года назад

think more the combo of both, heat softens the PLA and because its more malleable, it can react to the vapor, as normal vapor from acetone doesnt do anything to pla

@ChaozXIII 3 года назад

that means amazon basics is an impure filament mixed with abs

@tamroberts7303 3 года назад

This. I've literally soaked my hatchbox PLA(in the past) in Acetone(pure) and It did nothing to it.

@ChaozXIII 3 года назад

and that is a good thing

@WaynesWorkshop 3 года назад

while its true it wont do much in pure aceton, its the combo of heat and acetone vapor that does the trick, these same models dunked in pure (cold) acetone wont give any reaction either

@IrocZIV 3 года назад

Why do you think this technique works so well when an acetone vapor bath by itself does little smoothing?

@WaynesWorkshop 3 года назад

well i dont think anymore, i know ;) all jokes aside, a vapor bath on its own generates no heat, the combination of heat (to make the pla soft) and than the vapor hitting is what does the trick, ofcourse as shown in the video not every brand of PLA reacts the same. some purists go "wEll YoU dOnT uSe PuRe PLA!" but who does nowadays, pretty much everybody i know and see in every 3dprinting group goes for what is available for a good price vs ok quality.

@AlWolf_13 4 года назад

Давай, давай мужик! Очень интересные видео, не зря подписался.=)

@Bublerkin 3 года назад

I need a large pot to make things smooth

@polgadototter 29 дней назад

tried for several hours its a nogo it doesnt do a thing

@WaynesWorkshop 28 дней назад

hours???? then your pla is probably a melted slush... like mentioned in the video, not all PLA's work, the pla plus brands i had reacted very little to it.

@lizarrrdbeth 3 года назад

OMG...I want to be friends. I want to come over and chat your ear off. Just got into this hobby myself. Lots of noobie questions answered so thank you. Can't wait to try the spray puddy!!

@hulkgqnissanpatrol6121 3 года назад

Seems like your using cheap filament!! Pla is non-reactive. If your Pla is reacting it's not "shit" it's a better Pla! Yes Pla ➕ will react but the filament will most likely not dissolve evenly leaving streaks/lines. Abs on the otherhand will do exactly what your TRYING to do.

@WaynesWorkshop 3 года назад

ive used 6 different brands of pla, all at different price points, regardless of price, it still prints with the same ease, abs i used to print with, the enclosure simply was to cumbersome in my current shop