Тёмный

Polaris Quattro Sport and Quattro P40 Not Moving: Complete Cleaner Troubleshooting and Rebuild Video 

Swimming Pool Tips, Reviews & How To - SPL
Подписаться 126 тыс.
Просмотров 31 тыс.
50% 1

The Polaris Quattro Sport and the P40 (Shown in this video) are one in the same cleaner but with a different color scheme and market sector. Both are only available at your local retail pool store or from your pool service provider and the white Quattro P40 is sold out of Leslie’s Pool Supplies. Regardless of which model you have the Quattro is a truly awesome pressure side cleaner.
If you are on the fence about buying one of these units and think they may be over complicated, watch the video and see how easy it is to change out the parts. For me it was one of the easiest Polaris Cleaners to work on. I go over changing basically every wear part in the video and here I will go over what every part does so that you will have a guide to go along with the video.
Check System First:
Because of the nature of how a pressure side cleaner works, check to make sure both the system pump (main pool pump) and the booster pump (cleaner pump) are set to come on at the same time. The main pump if it is a VS pump should be running at a higher speed, around 2200 RPM or greater is acceptable. If the system pump and booster pump are not set to turn on at the same time the Quattro will not move.
Check the Quick Disconnect:
Make sure the Quattro has enough water going to it. Sometimes the black dot pressure relief valve is open or cracked. Typically, it should be closed if you have a ¾ hp booster pump connected to the Quattro. Also, check the debris screen in the line to make sure it is free of debris. When you clean your filter or if your filter grids or cartridges have tears in them, debris can get into the booster pump line and clog up the screen. If the screen is clogged the cleaner will not move.
Polaris Quattro Sport Gearbox Assembly | R0837300:
Like the MX8 and MX6 cleaners which use one or two Direction Devices the Gearbox Assembly is very similar in nature to that part and it will be the main part, you will be replacing on the Quattro. It is the part that turns and pivots the cleaner and since it is constantly turning and pivoting in the pool you can expect the gears in here to wear down. If you see the Quattro not turning in the pool that would be the part I would suspect needs replacing.
Polaris Quatro Sport Drive Shaft Assembly | R0837500:
The Dive Shaft Assembly looks very buff and robust compared to the one found on the Polaris 280 but then again, the Quattro does do a lot of wall climbing and is a much heavier cleaner. I suspect even though the Drive Shaft Assembly looks strong it will eventually wear out as it constantly is spinning the wheels. If you notice the Quattro not moving fast or moving well, see if the teeth on the drive shaft are worn down.
Polaris Quattro Sport Wheel | R0837000
On each wheel is a set of jagged teeth which either is grabbed by the driveshaft or the Engine Assembly and these teeth will eventually wear down. Again, if you check the driveshaft and it looks fine, check the teeth on each of the wheels for wear. If the teeth are worn down the Quattro will not move. Also, check the bearings in each wheel, there are 2 in each wheel. If they are broken or worn down the cleaner will move slowly.
Polaris Quattro Sport Axle | R0837100
Since the cleaner does a lot of wall climbing and bouncing off of stairs and such in your pool, don’t be surprised if one of the plastic axles may snap or crack. If the wheels feel especially wobbly the cleaner may have a broken axle. These are easy to replace and affordable.
Polaris Quattro Sport Engine Assembly with O-Ring | R0837200
This is what drives the Quattro as all of the parts come together to move the cleaner. Much like the Engine in the Zodiac MX8 or MX6 cleaner, when the engine wears out the other parts will not spin well and you will notice the Quattro moving slowly in the pool. Replacing the engine will get everything moving again.
Of course, there are other parts that can wear but knowing basically how the cleaner moves will give you a better understanding of what parts to replace. Polaris Quattro Sport Gearbox Assembly | R0837300 turns the cleaner. Polaris Quattro Sport Engine Assembly with O-Ring | R0837200 brings many of the moving parts together to create movement. Polaris Quatro Sport Drive Shaft Assembly | R0837500 spins the wheels to move the cleaner. Any parts attached to these main parts that fail will stop or slow down the Quattro.
Visit my Website: www.swimmingpoo...
eBook: www.swimmingpo...
RU-vid Video Index: poolmandave.blo... - A list of all of my videos.
Shop at Leslie's: Leslie’s Pool Supplies has been do-it-yourselfers and pool trade professionals trusted partner since 1963, providing quality products and services to make pool care easy and solutions and expertise to do it right. lesliespool.com/?

Опубликовано:

 

9 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 85   
@waltergandra
@waltergandra 2 года назад
Mine started to go in circles after 1 year... Great video... Thanks!
@Optix-Code
@Optix-Code 2 года назад
Your gearbox is not working correctly and is broken. It should be covered under warranty if you bought it with Leslie's. Just don't run more than one 1 or 2 hours a day
@terrythompson4126
@terrythompson4126 2 года назад
Thank You so much for this wonderful video! You have answered SO MANY questions! This was seriously the most informative 13:59 of my weekend! You have replaced my stress with empowerment! Thank you again!!!!
@jessedies2385
@jessedies2385 Месяц назад
Appreciate this video. Saved me a ton of money. I would never attempted this without a tutorial.
@Barney777
@Barney777 2 месяца назад
I have to say thank you for helping me out. I didn’t find a video like this to help me take apart a cleaner and this was amazing.
@mrdelaware1
@mrdelaware1 Год назад
Awesome tutorial video! Thank you sooooo much for making this. The added part numbers as you walked thru each step was the icing on the cake. This will help guide me this week as I troubleshoot why my cleaner isn't working the way it used to. Thanks again!
@DysDys51
@DysDys51 2 года назад
Great video. Started taking it apart. A screw wasn't tight from the manufacturer, dislodged, and jammed itself into the wheel gears. Would only turn a quarter of the way. Found out where the screw was supposed to go. Done. Back in business. Thank you for the great video.
@davidb-jk8qf
@davidb-jk8qf 5 месяцев назад
Excellent tutorial. Extremely well done and a huge help. I hope you received the well-deserved super thanks I just sent.
@joeykramer7282
@joeykramer7282 Год назад
I’m about to purchase this cleaner and was doing some research on performing maintenance on it when I ran across this video. Great and informative video
@JZeverybody
@JZeverybody 2 месяца назад
Help! I have nothing but problems with my Polaris Quattro P40. Changed so many parts ($$$) and same issue. Right wheels either not spinning or stop under any resistance. Please any advice I'm dealing with this for 2 yrs. Leslie and Polaris no help.
@windleda
@windleda 5 месяцев назад
Great video. Super helpful, thanks.
@schnoogie45
@schnoogie45 2 года назад
great video ... saved me alot of $$$
@Emetdavid
@Emetdavid Год назад
My Polaris Quattro sport gets stack on the Jets returning water to the pool. It can get stacked for hours and the problem is that if the jet from the quattro points upward, I can lose a lot of water from the pool to the outside. Any solution?
@WilliamBrandfass
@WilliamBrandfass 5 месяцев назад
My Polaris F40 moves forward just fine, but will not rotate and change directions. As a result, it gets stuck on the steps.
@KimberlyTrexler
@KimberlyTrexler Месяц назад
What if water is shooting out of the feed hose connector, would a new o ring be a fix and WHERE does that o ring go? I've looked for videos and can't find any that talk about how to replace that o ring.
@SPL
@SPL Месяц назад
It might be cracked. Look at it carefully
@jean-claudejacquet7824
@jean-claudejacquet7824 11 месяцев назад
I need your help and advice about my Polaris Quattro, when I test it I see that hydraulic motor isn’t waterproof. Normal or not
@SPL
@SPL 11 месяцев назад
I don't think those parts need to be.
@lisatune884
@lisatune884 6 месяцев назад
Have you heard that the main controllers are dying? Can’t get the Leslie’s locations to look at mine and they say there’s no point. It’s 3 years old. Thanks for a great video!
@SPL
@SPL 6 месяцев назад
Haven't heard of that. But you can contact Polaris directly by calling Jandy. They might be able to help.
@davidb-jk8qf
@davidb-jk8qf 5 месяцев назад
Thanks!
@SPL
@SPL 5 месяцев назад
Thank you for your generous tip!
@toddlokash7865
@toddlokash7865 Год назад
I have rebuilt this cleaner 4 times. When is works it works well. What do you suggest the issue could be if it is simply not moving? When I hold it in place, everything turns. When I put it on the bottom of the pool it barely moves. I have changed all of the fittings on the hose, taken the entire cleaner apart and put it back together again. The gear box and engine are not even a year old. The pump is running but I have no way to verify the rate of flow. What could be wrong that I am not seeing? Im about done with the design. It is very expensive to keep running.
@SPL
@SPL Год назад
It could be the booster pump. Easy to check. Remove the quick disconnect. Turn on booster pump. If you can put your hand over the jet and stop the water flow there is not enough flow. Your hand should not be able to cover the pressure line and stop the flow.
@chriswherbert
@chriswherbert 6 месяцев назад
Great video, thank you for this! Before I start, quick question, maybe you can direct me to what I should look at first. Ours stopped moving, when the booster is off I can manually spin the wheels fine, when the booster is on the wheels lock up and I cannot manually turn the wheels. Gear box issue?
@SPL
@SPL 6 месяцев назад
Sounds like it if the front brush doesn't jam up when you move it by hand
@shrev94412
@shrev94412 Год назад
Can you do a video on how to replace the spring latch for the debris canister cover?
@bobbieayala-mk5tq
@bobbieayala-mk5tq Год назад
Will a sinking chlorine tablet holder interfere with my Polaris Quatro pool cleaner?
@SPL
@SPL Год назад
It might. I wouldn't use one with this cleaner in the pool.
@leilaatx2365
@leilaatx2365 Год назад
How do you replace the two gray latches on the inside? I’m having trouble removing mine. Not sure if there is debris stuck in the grooves making them tight, but I can’t get those suckers out! Already have the replacement pieces.
@SPL
@SPL Год назад
I am not sure the minute mark, but everything is either screwed in or set in the cleaner. So they should be able to come out.
@tonyconsolo2391
@tonyconsolo2391 Год назад
Admittedly, those little boogers are tough to get out, but I will say, they will slide out if you push on them from the back. I tapped mine out with a wood dowel and a couple taps on the dowel with a hammer.
@Mrwind2222
@Mrwind2222 7 месяцев назад
great video - Thanks! - Just took mine apart and ordered the gearbox and engine as both are defective. Any idea where to find the individual gears? can't find the detailed drawings of the individual gears
@SPL
@SPL 7 месяцев назад
I think they only sell the entire part.
@jenniferwedner8128
@jenniferwedner8128 Год назад
How to replace the latches?
@twiladove5312
@twiladove5312 2 года назад
This is a great video, thanks so much for doing this. It has helped me a lot. I do have one problem. My debris canister keeps popping off. I replaced it with a new one but it is still loose. Should I replace the body as well? I can see some wear at the latch area.
@SPL
@SPL 2 года назад
Maybe it is under warranty. Sounds like a defect to me.
@tonyconsolo2391
@tonyconsolo2391 Год назад
I had the same problem. There are two hinges at the back of the cannister, but they are attached to the lower half of the frame. Mine were super-worn and allowed a lot of movement of the cannister and lid. I replaced those AND the Latch that is in the lid. Problem solved. Both parts are about $15.00 ea.
@stiventoro4530
@stiventoro4530 2 года назад
Thank you for your videos great help . Could you tell me how could I adjust the rotation in the Polaris Quatro? It rotates for more than a minute and move forward for less than a minute. Any info highly appreciate it
@SPL
@SPL 2 года назад
Try adjusting the water pressure to the cleaner up to get faster rotation. At the quick connect you can make some adjustments.
@beast-magicwheelsmc6451
@beast-magicwheelsmc6451 3 года назад
How do you remove the brush assembly? you kind of skipped that part in the video. remove the 2 screws and then??
@SPL
@SPL 3 года назад
yes
@neonlights_live
@neonlights_live 3 года назад
on the right side gear box, should the white gear on the outside (connecting with the wheel) move freel? Mine slides back and forth but it seems like it should be more locked in place.
@SPL
@SPL 3 года назад
Everything should be pretty tight.
@rdnorris123
@rdnorris123 3 года назад
same problem and the scrubber doesn't turn like the other side so it goes in circles and won't climb. Is this the gear box as well?
@Optix-Code
@Optix-Code 2 года назад
@rdnorris123 Sounds like youre running it too long and your brush assembly on that side is no good and your gear box is out as well.
@tonyconsolo2391
@tonyconsolo2391 Год назад
@@rdnorris123 It's the Gearbox. Easily replaced, but NOT cheap. Poor Gearbox design by Polaris. My Quattro is 3 years old and I am on my 3rd Gearbox.
@punchdrunkdigital07734
@punchdrunkdigital07734 2 года назад
hello, we just installed this machine and it's going great. Only issue i'm having is that on it's scheduled startup it just sits in one place till you give it a shove, then it's good to go. water pressure issue?
@SPL
@SPL 2 года назад
Check the front roller to make sure it is aligned. That could be the issue.
@brianl5445
@brianl5445 Год назад
I’ve had mine just over a year and I’m having to give the cleaner a tug now as well. This issue started a month ago.
@cyrillegodinot7617
@cyrillegodinot7617 4 года назад
Do you know where I can purchase the broken Axle : Polaris Quattro Sport Axle (R0837100) Thanks
@SPL
@SPL 4 года назад
I get it. A known issue.
@cyrillegodinot7617
@cyrillegodinot7617 4 года назад
Where to buy on line ?
@SPL
@SPL 4 года назад
@@cyrillegodinot7617 www.poolsupplyunlimited.com/pool/polaris-r0837100-axle/177535p1
@Kate9980
@Kate9980 Год назад
Great video! Thanks for posting it. We have this same unit and it has no issue moving around the pool, but it all of a sudden quit picking up debris. No suction at all. Have you ever seen this problem with the quattro? Thanks again!
@SPL
@SPL Год назад
Front brush might be jammed with debris.
@Kate9980
@Kate9980 Год назад
​@@SPLthanks for the reply! That was something we had checked already and it didn't appear to have any debris or blockage. We ended up selling it for parts last weekend. Replaced it with the cheaper Polaris P28 and unbelievably, that little bugger works soooo much better than the gigantic Quattro ever did. I guess it was just the wrong cleaner for our pool.
@Optix-Code
@Optix-Code 2 года назад
As retail person please bring if under warranty first we will take care of you. 2 years with Leslie's. Please always check your manifolds for cracks and broken grids. Only need to run the Quattro for about an hour to two a day.
@terrythompson4126
@terrythompson4126 2 года назад
@Kevin Y. Well... wouldn’t that be nice! But we can’t even get a straight answer, warranty information, let alone a call back from any member of management at our Leslie’s here in San Angelo, Tx. regarding one of our sand filters. The whole Leslie’s experience HERE has left a lot to be desired, to put it nicely. I can’t begin to imagine the B.S. that I would have to endure if I took the Polaris in. Furthermore, one of the last times I was in there (following up on the filter issue) and mentioned the Polaris issues to the assistant manager and asked if I could bring it in and exchange it since was a recent purchase. I was told “No Exchange” the manager would have to look at it and see if she could fix it and if not, then it would have to be sent back to Polaris for further warranty or replacement. But since we can’t get the manager to use a simple telephone, I’m a little worried about a screwdriver! And if the Polaris takes as long as the filter issue is taking... the warranty will run out! Kevin, you seem knowledgeable, and customer service oriented. Do you work for Leslie’s? If so, can we contact you at your store and some informed help?
@Optix-Code
@Optix-Code 2 года назад
@Terry Thompson Yes, I'm manager for Leslie's in Houston.
@terrythompson4126
@terrythompson4126 2 года назад
@@Optix-Code Oh, wow! What a lucky 🍀 break! Houston is pretty big! If someone wanted to locate a knowledgeable manager in what part of Houston should they start? I’m asking for a friend 🤣🤣
@Optix-Code
@Optix-Code 2 года назад
@Terry Thompson give me you info and I'll be more than happy to speak to you.
@Optix-Code
@Optix-Code 2 года назад
@Terry Thompson fyi Spring and The Woodlands area
@fatthor2476
@fatthor2476 2 года назад
great video!!! question: is there a tread-wear indicator on the tires? I own one and it just started to spin and not reach the furthest wall like it used to. I noticed the side-brushes were extremely worm so I ordered new ones from Leslies. Maybe I should replace the tires and roller brush too?
@SPL
@SPL 2 года назад
Would say to replace those parts. Sounds like it is time.
@fatthor2476
@fatthor2476 2 года назад
@@SPL thanks for the response! is there a known issue with the right side-brush gear box? seems that the roller brush is not spinnign great
@tonyconsolo2391
@tonyconsolo2391 Год назад
@@fatthor2476 YES! Essentially there is ONE gearbox, but is the Right Side that has always failed on mine. My Quattro is 3 years old and I am on my THIRD Gearbox. Poor design by Polaris. I did notice that they changed at least the outsidegear from plastic to aluminum on the latest one I ordered. There may be some internal parts changed, but I haven't taken this one apart yet.
@fatthor2476
@fatthor2476 Год назад
@@tonyconsolo2391 Thank you. I replaced the gearbox with an aluminum one and it is back to working great.
@JZeverybody
@JZeverybody 3 года назад
I have a problem with my p40. Stays in deep end and just circles the same area. What could it be?
@SPL
@SPL 3 года назад
It could be a couple of things. 1st check the pressure going to the cleaner and make sure it is in range.
@JZeverybody
@JZeverybody 3 года назад
@@SPL ok will.
@rdnorris123
@rdnorris123 3 года назад
@@JZeverybody I bet it's the right side gear box. I have same problem, scrubber on right side (standing behind it) doesn't turn forward as fast and it wont climb walls either
@JZeverybody
@JZeverybody 3 года назад
Yes I replaced the engine and gear box. It works better, but, still not great. Stays in deep end and seems to spin on the waste drains for awhile before it moves on. Definitely not working like the day i purchased it. Not sure what to do...
@rdnorris123
@rdnorris123 3 года назад
@@JZeverybody call customer service and request a replacement
@WhyYouAskingMe
@WhyYouAskingMe 4 года назад
Did Polaris ever get back to you about their top tier robot; if it is able to clean Baja / pool shelf? They haven't emailed me back yet. Thanks 😀
@SPL
@SPL 4 года назад
Nothing yet.
@drewgalvan8825
@drewgalvan8825 2 года назад
Where do you guys go for parts?
@SPL
@SPL 2 года назад
Your local pool store can order them.
@drewgalvan8825
@drewgalvan8825 2 года назад
@@SPL thank you!
@1613ckhris
@1613ckhris Год назад
I have been replacing gears in this thing a year after I bought it. I have the new stainless gear for both gear boxes but the gears inside the gear box are still plastic and do not last long at all. These gearboxes are not cheap. Why Polaris doesnt sell gears is beyond me… these boxes can easily be rebuilt. I am very disappointed in this pool cleaner and once I get tired of replacing parts will be trying a non booster pump model and not a Polaris
@maxwellholloway9029
@maxwellholloway9029 4 года назад
To bad the right side gear box is trash.
Далее
Polaris Pressure Relief Valve Replacement
7:18
Просмотров 26 тыс.
Polaris QUATTRO Sport Set Up and Installation Video
5:57
Leah Quattro/P 40 drive issue
4:04
Просмотров 4,7 тыс.
The Easiest Way to UNCLOG your Swimming Pool Skimmer!
9:57
Polaris Thrust Jet Adjustment
3:45
Просмотров 89 тыс.
4 Things You Didn't Know About Robotic Pool Vacuums
3:35
How to PRIME a Swimming Pool Pump | Very Informative!
12:50